Air bag warning light.
Discussion
My Monaro has had the airbag warning light on ever since i took the seats out to dry the carpet after a water leak (which im still not convinced ive sorted), will that light being on cause it to fail its M.O.T and if so can it be re-set via the buttons in the car (like the service light) or does it involve a trip to Picadors, or can my local garage do it when he M.O.Ts it?
If it involves plugging a lappy into it where the er plug?
(Monaro LS2 VXR)
Thanks in advance.
If it involves plugging a lappy into it where the er plug?
(Monaro LS2 VXR)
Thanks in advance.
GEARJAMMER said:
My Monaro has had the airbag warning light on ever since i took the seats out to dry the carpet after a water leak (which im still not convinced ive sorted), will that light being on cause it to fail its M.O.T and if so can it be re-set via the buttons in the car (like the service light) or does it involve a trip to Picadors, or can my local garage do it when he M.O.Ts it?
If it involves plugging a lappy into it where the er plug?
(Monaro LS2 VXR)
Thanks in advance.
Comms Plug under dash below Steering WheelIf it involves plugging a lappy into it where the er plug?
(Monaro LS2 VXR)
Thanks in advance.
and Yep Loadsa New MOT regs including Airbag lights and Door open lights and all sorts of silly stuff

Sorry, Dunno what it will take to reset it tho
Typically Tech2 is needed. If you're handy with a soldering iron and understand sending data out of a serial port, you can do it yourself though apparently (I've not tried it)
The americans are your friends on this, try the following:
http://www.ls1gto.com/forums/showthread.php?t=4603...
There's a command line tool written for setting all the cluster stuff (shift lights, shut down logos etc.) here:
http://www.ls1gto.com/forums/showthread.php?t=5170...
(This one is specific to the addition of airbag reset functionality)
http://www.ls1gto.com/forums/showthread.php?t=5665...
And some info on making the cable if the circuit diagram isn't much use:
http://www.ls1gto.com/forums/showthread.php?t=5798...
I haven't tried any of this, it's similar to what Ferret has done, but without a cluster to test it on, I'd exercise some caution...
Hope that helps
The americans are your friends on this, try the following:
http://www.ls1gto.com/forums/showthread.php?t=4603...
There's a command line tool written for setting all the cluster stuff (shift lights, shut down logos etc.) here:
http://www.ls1gto.com/forums/showthread.php?t=5170...
(This one is specific to the addition of airbag reset functionality)
http://www.ls1gto.com/forums/showthread.php?t=5665...
And some info on making the cable if the circuit diagram isn't much use:
http://www.ls1gto.com/forums/showthread.php?t=5798...
I haven't tried any of this, it's similar to what Ferret has done, but without a cluster to test it on, I'd exercise some caution...
Hope that helps

SturdyHSV said:
Monkfish were very accommodating to my many requests to read/reset the codes whilst I was sorting out the dummy loads for my seats, so if you're getting something done there, you could always ask nicely 
Yes. I have the problem still with the ute (same as 05 VXR's)and must try to get it sorted sometime. MF did do the tech2 reading but the code wasn't explicit enough to help deduce the problem. Having said that it could be seat related.
MyM8V8 said:
Yes. I have the problem still with the ute (same as 05 VXR's)and must try to get it sorted sometime. MF did do the tech2 reading but the code wasn't explicit enough to help deduce the problem. Having said that it could be seat related.
Do you remember the code? Happy to look up the parameters that trigger it for you 
Gassing Station | HSV & Monaro | Top of Page | What's New | My Stuff



