It is officially dead...
It is officially dead...
Author
Discussion

djwilk

Original Poster:

1,693 posts

200 months

Sunday 23rd March 2014
quotequote all
Sorry for repeating myself, but now that I have taken the engine out completely, I can say the plan of resurection of the block is not gonna work. The reason is a hole on the off side of the block just behind the starter motor and near side parallel. Moreover, the oil sump got cracked as well...

So... Off to find new shineys I'm afraid... I don't want to sound inappropriate and risk this thread closed, but are any remaining parts like pistons, rods, heads etc worth anything apart from scrap metal? As said before I want to keep the block and use it as a coffee table, but how heavy is it? Only asking because the short block assy that I pulled out yesterday weighs a million tons!!! I can only hope a bare block weighs a lot less? Otherwise, I might need two people everytime I want to move my table!?!?

ARAF

20,759 posts

254 months

Sunday 23rd March 2014
quotequote all
I think we've been here before. Unfortunately it is now worth less than when you started pulling it apart in the real world, but I still think you either need to cut your losses and sell what's left, or put a create motor in.

djwilk

Original Poster:

1,693 posts

200 months

Sunday 23rd March 2014
quotequote all
Sorry, I should have made myself clear. I am not trying to sell the car, but see if there is any value in remaining engine parts, since pistons, tods etc are all good, heads included.

I also saw the Edelbrock engine + Tremec TKO500 on Roadcraft and wonder if this is any good if I were to selll the gearbox and the new LS7 clutch I've got sitting an waiting to go in. Also, is Edelbrock just a company that puts these together?

djwilk

Original Poster:

1,693 posts

200 months

Sunday 23rd March 2014
quotequote all
Also, can this be installed with a NA setup?

https://chevroletperformanceparts.com/p/lsx376-b8-...

raving

1,183 posts

221 months

Sunday 23rd March 2014
quotequote all
Easiest thing to do is buy a brand new Ls3 £5300 (Gmpp) and fit it ,job done , sell off anything you can you have left


djwilk

Original Poster:

1,693 posts

200 months

Sunday 23rd March 2014
quotequote all
raving said:
Easiest thing to do is buy a brand new Ls3 £5300 (Gmpp) and fit it ,job done , sell off anything you can you have left
I know, but I think I am falsely hoping I could build sth else cheaper and still have some fun whilst doing it...

ARAF

20,759 posts

254 months

Sunday 23rd March 2014
quotequote all
djwilk said:
raving said:
Easiest thing to do is buy a brand new Ls3 £5300 (Gmpp) and fit it ,job done , sell off anything you can you have left
I know, but I think I am falsely hoping I could build sth else cheaper and still have some fun whilst doing it...
Gary could probably supply all the parts that you need, from his business. If he is saying that a crate motor is your cheapest option, then he needs listening to. Honest.

raving

1,183 posts

221 months

Sunday 23rd March 2014
quotequote all
djwilk said:
I know, but I think I am falsely hoping I could build sth else cheaper and still have some fun whilst doing it...
You wont build nothing cheaper than that with a warranty on it

djwilk

Original Poster:

1,693 posts

200 months

Sunday 23rd March 2014
quotequote all
ARAF, What other parts would I need?

Raving, if I replace the cam and springs I will loose warranty anyway, won't I?

richie slow

7,570 posts

195 months

Sunday 23rd March 2014
quotequote all
We are approaching the area where you need to pm each other.

Thanks for your co-operation clap

ARAF

20,759 posts

254 months

Sunday 23rd March 2014
quotequote all
djwilk said:
ARAF, What other parts would I need?

Raving, if I replace the cam and springs I will loose warranty anyway, won't I?
If you buy the standard crate LS3, then you need nothing else. If you buy the cam'd one, then you will need a remap.

You will even have parts from the old engine that you can sell - like the heads, intake etc

I wouldn't start changing the springs and cam - yes, you'll lose the warranty.

djwilk

Original Poster:

1,693 posts

200 months

Sunday 23rd March 2014
quotequote all
Thanks ARAF, and this is exactly where I am heading. No real benefit of the warranty, and I guess crate from US will not save a penny from what I remember. Hence my brave idea of building the bottom end to what I've already got, especially that the remainders are only worth what someone is willing to pay for them, less the fact that we have got a very limited market for the LS V8 stuff in the UK and, more importantly, the incomplete V8 internals I have (lack of one cylinder).

Richie, sorry about coming close to the borderline.

richie slow

7,570 posts

195 months

Sunday 23rd March 2014
quotequote all
No probs mate smile

Sorry to be pedantic rolleyes

jameshsv

5,844 posts

191 months

Sunday 23rd March 2014
quotequote all
djwilk said:
Sorry, I should have made myself clear. I am not trying to sell the car, but see if there is any value in remaining engine parts, since pistons, tods etc are all good, heads included.

I also saw the Edelbrock engine + Tremec TKO500 on Roadcraft and wonder if this is any good if I were to selll the gearbox and the new LS7 clutch I've got sitting an waiting to go in. Also, is Edelbrock just a company that puts these together?
NTH of WATFORD is after a pair of ls2 heads.pm him

MyM8V8

9,468 posts

226 months

Sunday 23rd March 2014
quotequote all
raving said:
Easiest thing to do is buy a brand new Ls3 £5300 (Gmpp) and fit it ,job done , sell off anything you can you have left
This is the answer you will come to after going round in a million circles! Good advice, take it.

stevieturbo

18,105 posts

278 months

Sunday 23rd March 2014
quotequote all
djwilk said:
Sorry for repeating myself, but now that I have taken the engine out completely, I can say the plan of resurection of the block is not gonna work. The reason is a hole on the off side of the block just behind the starter motor and near side parallel. Moreover, the oil sump got cracked as well...

So... Off to find new shineys I'm afraid... I don't want to sound inappropriate and risk this thread closed, but are any remaining parts like pistons, rods, heads etc worth anything apart from scrap metal? As said before I want to keep the block and use it as a coffee table, but how heavy is it? Only asking because the short block assy that I pulled out yesterday weighs a million tons!!! I can only hope a bare block weighs a lot less? Otherwise, I might need two people everytime I want to move my table!?!?
Bare alloy block is around 40-50kgs from memory.

Obviously any scrap metal has some value...although overall still not a lot.

PWM list an LS3 in stock, so it would make a sensible purchase. Roadcraft's site would seem to suggest no stock, and for some baffling reason their prices dont include VAT

How bad is the sump ? It could maybe be welded ?

stevieturbo

18,105 posts

278 months

Sunday 23rd March 2014
quotequote all
djwilk said:
I know, but I think I am falsely hoping I could build sth else cheaper and still have some fun whilst doing it...
Cheapest is likely used, or source a new short motor from the US.

ie block, crank/rods/pistons etc then bolt your heads back on.

Or on the upgrade front, source a larger cc short motor.

djwilk

Original Poster:

1,693 posts

200 months

Monday 24th March 2014
quotequote all
Thanks chaps, this makes a lot of sense (well, it did first time around as well).

I guess last thing to establish for me is weight of a shortblock vs crate engine and whether stock LS3 cam, exhaust manifolds or other bits like water pump etc have got any value.

Perhaps, I could PM anyone of you to help me establish value of my scrap?

Also, whilst comparing LS3 vs LS376 @ 480 vs Ls376 @ 525 is it just the ASA cam (which I know is undriveable) that makes nearly 100bhp over stock?

Ps. If I am already running decat, would I need to just get shorter decat pipes made for new long headers?

Edited by djwilk on Monday 24th March 07:21

stevieturbo

18,105 posts

278 months

Monday 24th March 2014
quotequote all
djwilk said:
Thanks chaps, this makes a lot of sense (well, it did first time around as well).

I guess last thing to establish for me is weight of a shortblock vs crate engine and whether stock LS3 cam, exhaust manifolds or other bits like water pump etc have got any value.

Perhaps, I could PM anyone of you to help me establish value of my scrap?

Also, whilst comparing LS3 vs LS376 @ 480 vs Ls376 @ 525 is it just the ASA cam (which I know is undriveable) that makes nearly 100bhp over stock?

Ps. If I am already running decat, would I need to just get shorter decat pipes made for new long headers?

Edited by djwilk on Monday 24th March 07:21
Exhaust manifolds maybe some....if you find a buyer. But they are compact and would suit some conversions.

Water pump will always have value, people do replace them. Cam not so much.

Weight. I'd guess a shortblock in the region of 100-120, and full crate around 160-180kgs

If talking actual scrap metal value, case of phoning round scrap metal dealers. You might get £30-40 for it all.

eliot

11,999 posts

285 months

Monday 24th March 2014
quotequote all
Do the cammed engines pass the MOT? I'm sure i read on the ultima section someone having issues with the 480?