Burning smell...
Author
Discussion

j666eds

Original Poster:

642 posts

180 months

Tuesday 8th April 2014
quotequote all
Hi,

I have a burning smell coming from inside my 'ro when the heating is on. Smells a bit like burning plastic. I have checked around the car that the exhaust isn't touching anything or i haven't got a plastic bag melted onto it. It appears to be only when i set the temp to hot, cold there is no smell. I did a quick search on some aus forums and one possible cause that appeared to come up a few times was the heater matrix is leaking??? I did hear the cooling system "gurgling" just before the smell started. I appear to have no loss of coolant though.

Does anyone have any idea what it could be or has anyone else had the same problem? i don't really fancy taking all the dash out!

Thanks

James

neiljohnson

11,298 posts

238 months

Wednesday 9th April 2014
quotequote all
Could be the heater fan resister try the heating on full with the fan off & see if you still get the smell

SturdyHSV

10,443 posts

198 months

Wednesday 9th April 2014
quotequote all
For what it's worth, taking the entire centre of the dash out is a total of 7 easily accessible screws, and is a doddle to put back in.

The stereo is the only awkward bit, I think you have to take it out to get the centre out (mine was already out...)

There's 1 screw on the driver's side of the little tray in front of the gear stick (you can just see the screw hole in the picture below), then you just pry the lower centre trim up from the centre armrest. In the picture the armrest is back down, but you can see where the trim is partially lifted.



Careful pulling on wires etc. you can leave everything connected and just sling it off to the side if you want. You'll probably want the gearstick in 4th so it's out of the way.

Now that that's gone, it'll expose 2 screws at the bottom of the centre console. In the picture, that is the little tray I was talking about, the screw is at the back of that.



Undo those two, then remove the top panel where the gauges are (if it's a VXR). This just pops out, very simple.



Unplug the connector if you have gauges, and put that to the side. This has now exposed the final 4 screws to be removed.



Once they're out, just pull the whole thing out (pulling it back towards the rear of the car). Once it's mostly out, unplug the aircon / hazard button. The aircon unit easily unscrews (4 little screws) from the centre trim, so you can take that off and connect it back up for testing the system.



Extra lightweight trim option...


KMud

2,924 posts

187 months

Wednesday 9th April 2014
quotequote all
Good info Sturdy, but how many more steps to get to the heater core?

SturdyHSV

10,443 posts

198 months

Wednesday 9th April 2014
quotequote all
KMud said:
Good info Sturdy, but how many more steps to get to the heater core?
Not a clue, I shall consult the manual! hehe

j666eds

Original Poster:

642 posts

180 months

Wednesday 9th April 2014
quotequote all
KMud said:
Good info Sturdy, but how many more steps to get to the heater core?
From what ive seen on other forums its a complete c word!

SturdyHSV

10,443 posts

198 months

Wednesday 9th April 2014
quotequote all
j666eds said:
From what ive seen on other forums its a complete c word!
The manual I have is rather lazy on detail, it frequently defaults to 'it's the same as the VX series', you look there and it says 'it's the same as the VT series' and by the time you get back to there the interior looks pretty different and the screws aren't in the same places any more!

Happy to send it over to you if you want a browse, there's probably some useful information hidden away in there somewhere...

KMud

2,924 posts

187 months

Wednesday 9th April 2014
quotequote all
Hope I never need to know really! I've had the centre out as you've demonstrated (recently, more times than I'd have liked...), and did the vent trim bits for the tweeters (bad enough)...but with the centre section out I couldn't see an easy way of digging deeper into the centre section without yanking the largest part of the dash, and that probably requires removing the glovebox and god knows what else...

Z0m81e

249 posts

173 months

Wednesday 9th April 2014
quotequote all
FWIW i've had the glove box out of mine and I don't recall it being too hard. I'm at Walkinshaw at the mo so can't look but if you need more info let me know and i'll check later/tomorrow.