Spongy clutch on VXR Monaro 6.0
Discussion
Got a problem with my monaro when thrashing it (which is most of the time) more so when a lot of gear changing involved (rather than same gear motorway speed).
The clutch goes spongy and changing gear becomes difficult as it feels there is no clutch there. my first thought was that the clutch fluid was overheating ? dont think its anything wrong with actual clutch as no smell of burning clutch.
Anyone had the same problem?
steve
The clutch goes spongy and changing gear becomes difficult as it feels there is no clutch there. my first thought was that the clutch fluid was overheating ? dont think its anything wrong with actual clutch as no smell of burning clutch.
Anyone had the same problem?
steve
Common issue. If the clutch fluid is anything but clear then it needs replacing.
There is a good thread here to explain it all http://www.rangeracceleration.com/Clutch_Care.html
There is a good thread here to explain it all http://www.rangeracceleration.com/Clutch_Care.html
ringram said:
Common issue. If the clutch fluid is anything but clear then it needs replacing.
There is a good thread here to explain it all http://www.rangeracceleration.com/Clutch_Care.html
thanks for that rich, will get that sorted at monkfish this week.There is a good thread here to explain it all http://www.rangeracceleration.com/Clutch_Care.html
petrolzed said:
Thrashing it most of the time? On a public road,Give me a break!
mate, if you dont drive it hard on the roads then why bother having it!!! northants and oxon no police to speak of just cameras. now linconshire is different got done twice in a month driving a 407 estate! sk_uk said:
ringram said:
Common issue. If the clutch fluid is anything but clear then it needs replacing.
There is a good thread here to explain it all www.rangeracceleration.com/Clutch_Care.html
There is a good thread here to explain it all www.rangeracceleration.com/Clutch_Care.html
thanks for that rich, will get that sorted at monkfish this week.
Can you let us know how it goes? Mine is doing just the same, and I'm just about to book it in for its 20k service. If it does the trick for you I'll make sure to get mine done as well.
sk_uk said:
i have been told that this wont cure the problem and that if you change the fluid it will be dirty again after not many miles. can you guys who have done the change of fluid let me know how you are getting on?
cheers
cheers
mine's still fine - I know this because I can still change gear where before I couldn't. It only takes 10 minutes so give it a go.
sk_uk said:
i have been told that this wont cure the problem and that if you change the fluid it will be dirty again after not many miles. can you guys who have done the change of fluid let me know how you are getting on?
cheers
cheers
Yep, goes dirty fairly quickly but then you just change it again, as Wormus says, 10 minutes max..
4 or 5 changes should pretty much flush it through. Interestingly, my pedal got lighter not firmer!!
Haven't looked but have the VXR's got braided clutch lines?
Had this problem on old M3 in hot weather where the original rubber hose would expand rather than exert pressure to the slave cylinder. Old perished hoses can have the same effect. Replaced the line with a steel braided version and fixed the problem immediately, gave better clutch feel as well.
just a thought
Had this problem on old M3 in hot weather where the original rubber hose would expand rather than exert pressure to the slave cylinder. Old perished hoses can have the same effect. Replaced the line with a steel braided version and fixed the problem immediately, gave better clutch feel as well.
just a thought
Monnington said:
sk_uk said:
i have been told that this wont cure the problem and that if you change the fluid it will be dirty again after not many miles. can you guys who have done the change of fluid let me know how you are getting on?
cheers
Yep, goes dirty fairly quickly but then you just change it again, as Wormus says, 10 minutes max..cheers
4 or 5 changes should pretty much flush it through. Interestingly, my pedal got lighter not firmer!!
Yep, sucking it all out actually. You won't get air in the system as when you top it back up it will rise to the top, as you use the clutch, the clean fluid mixes with the old left in the hose & slave and after a couple of changes you have clean fluid throughout.
The hose isn't braided by the way, and apparently there is quite a restriction at the bottom of the standard hose so replacing it is supposed to make quite a difference. Bit of a b'stard to get too though from what I can gather..
The hose isn't braided by the way, and apparently there is quite a restriction at the bottom of the standard hose so replacing it is supposed to make quite a difference. Bit of a b'stard to get too though from what I can gather..
Some formal recognition for this issue is noted here.
http://forums.corvetteforum.com/showpost.php?p=156...
Document ID# 1982105
Subject: Intermittent Spongy Clutch Pedal Sticking To The Floor During Hard Acceleration And High RPM Shifts - keywords contaminate fluid hydraulic #PIP4145 - (06/04/2007)
Models: 2005-2007 Chevrolet Corvette, Corvette Z06 Equipped with a Tremec 6-speed Transmission RPO MM6, MZ6
The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI.
Condition/Concern:
Some customers may comment about an intermittent spongy clutch pedal feel or clutch pedal sticking to the floor. This may be aggravated by aggressive driving and high clutch operating temperatures. Higher than expected levels of water in the clutch fluid greater than 2% may cause the clutch fluid to boil. The presence of water in the fluid lowers the boiling point significantly; when these conditions are present the driver may lose customary clutch pedal feel and performance.
Recommendation/Instructions:
If the above condition is intermittent flush the hydraulic system using DOT 4 fluid part number 88958860 (88901244 in Canada), prior to replacement of any mechanical or hydraulic components.
To eliminate the opportunity for moisture to enter the clutch hydraulic system.
The clutch fluid level inspection should be a VISUAL inspection only. Look through the transparent reservoir and observe the fluid level. Avoid removing the cap. Do not remove the cap just to top-off clutch fluid. Leave the system closed and sealed. During PDI inspection or routine servicing the cap should not be opened for just an inspection.
DOT 4 clutch fluid has a 2 week shelf life. Do not use fluid if container opening date is unknown or older than 2 weeks. Do not mix or re-use old fluid. Current service information already covers the issue of reuse.
To provide the best clutch operation, it is recommended that the owner change the clutch fluid every 2 calendar years. Please flush and replace the clutch fluid with P/N 88958860 (88901244 in Canada) or equivalent DOT 4.
The current service information and owners manual will be updated to reflect this information.
Note: If the concern is not intermittent, inspect clutch hydraulic system for leaks and repair as necessary after repairs are completed flush system with DOT 4 fluid part number 88958860 (88901244 in Canada).
Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed.
http://forums.corvetteforum.com/showpost.php?p=156...
Document ID# 1982105
Subject: Intermittent Spongy Clutch Pedal Sticking To The Floor During Hard Acceleration And High RPM Shifts - keywords contaminate fluid hydraulic #PIP4145 - (06/04/2007)
Models: 2005-2007 Chevrolet Corvette, Corvette Z06 Equipped with a Tremec 6-speed Transmission RPO MM6, MZ6
The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI.
Condition/Concern:
Some customers may comment about an intermittent spongy clutch pedal feel or clutch pedal sticking to the floor. This may be aggravated by aggressive driving and high clutch operating temperatures. Higher than expected levels of water in the clutch fluid greater than 2% may cause the clutch fluid to boil. The presence of water in the fluid lowers the boiling point significantly; when these conditions are present the driver may lose customary clutch pedal feel and performance.
Recommendation/Instructions:
If the above condition is intermittent flush the hydraulic system using DOT 4 fluid part number 88958860 (88901244 in Canada), prior to replacement of any mechanical or hydraulic components.
To eliminate the opportunity for moisture to enter the clutch hydraulic system.
The clutch fluid level inspection should be a VISUAL inspection only. Look through the transparent reservoir and observe the fluid level. Avoid removing the cap. Do not remove the cap just to top-off clutch fluid. Leave the system closed and sealed. During PDI inspection or routine servicing the cap should not be opened for just an inspection.
DOT 4 clutch fluid has a 2 week shelf life. Do not use fluid if container opening date is unknown or older than 2 weeks. Do not mix or re-use old fluid. Current service information already covers the issue of reuse.
To provide the best clutch operation, it is recommended that the owner change the clutch fluid every 2 calendar years. Please flush and replace the clutch fluid with P/N 88958860 (88901244 in Canada) or equivalent DOT 4.
The current service information and owners manual will be updated to reflect this information.
Note: If the concern is not intermittent, inspect clutch hydraulic system for leaks and repair as necessary after repairs are completed flush system with DOT 4 fluid part number 88958860 (88901244 in Canada).
Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed.
Recently I have been having trouble getting the ro into 1st gear, either before setting off, or when idle at traffic lights when I want to pull away. Would this be related to the fluid? would changing it help with this issue, or should I get it checked out?
Usually I have to put it into another gear a few times before it will let me get it in first. Can be a bit annoying when the lights change, and I can't pull away
Usually I have to put it into another gear a few times before it will let me get it in first. Can be a bit annoying when the lights change, and I can't pull away

Gassing Station | HSV & Monaro | Top of Page | What's New | My Stuff


