Will these wheels fit and tyre size information please?
Will these wheels fit and tyre size information please?
Author
Discussion

boggie

Original Poster:

393 posts

253 months

Saturday 3rd April 2010
quotequote all
http://cgi.ebay.co.uk/BMW-X5-GENUINE-

Hi all,

I have a 2006 CV8 and would like to upsize the weels to fit lower profile tyres. I quite like the look of these BMW X5 wheels and as they are standard fitment there are lots of second hand sets on Ebay. They are 19", come in either 9J or 10J width, 120PCD and 45 offset. I do not know if the centre bore is correct but as long as they are bigger then I should be able to get hold of a set of hubcentric rings to suit or even make a set on my lathe.

My questions are:

1. Will these rims fit?

2. How big can I go with the rear tyre size without fouling the arch. I would like to get as much rubber as possible and will consider reducing the arch return edge if needed.

3 What can I get away with on the fronts without fouling?

Many thanks,
B

Edited by boggie on Saturday 3rd April 19:55

Tattooboy

7,946 posts

209 months

Saturday 3rd April 2010
quotequote all
How you going to drive with 1 wheel ??

gsd2000

11,515 posts

214 months

Saturday 3rd April 2010
quotequote all
I thought the 9" versions were a +51 offset, so they will stick out a bit and you will need to trim the lip down.

I have a link to a site somewhere on my pc or you can google it regarding all the different bmw wheels including sizes, offsets and cars that they come off.

boggie

Original Poster:

393 posts

253 months

Saturday 3rd April 2010
quotequote all
As I understand it, the bigger the +ve offset number, the further in the wheel is:

Offset
The offset, measured in millimeters, can be negative or positive, and is the distance from the hub-mounting surface to the rim's true centerline. A positive offset means the hub-mounting surface is closer to the outside edge of the wheel, i.e. the wheel wraps around the hub and brake hardware more deeply; a negative offset means the hub-mounting surface is closer to the inside edge of the wheel and wheel sticks outwards more than inwards. When selecting aftermarket wheels, a wheel with too little positive offset will be closer to the fender, and one with too much positive offset will be closer to the suspension components. Wheel width, offset and tire size all determine the way a particular wheel/tire combination will work on a given car. Offset also affects the scrub radius of the steering and it is advisable to stay within the limits allowed by the vehicle manufacturer. Because wheel offset changes the lever-arm length between the center of the tire and the centerline of the steering knuckle, the way bumps, road imperfections and acceleration and braking forces are translated to steering torques (bump-steer, torque-steer, etc) will change depending on wheel offset. Likewise, the wheel bearings will see increased thrust loads if the wheel centerline is moved away from the bearing centerline.

gsd2000

11,515 posts

214 months

Saturday 3rd April 2010
quotequote all
Yes the centre of the wheel will be 3mm further in, but the rim is 1" larger than standard so it will stick out approx 10mm more than standard. There are offset calculators online.

S800VXR

5,877 posts

231 months

Saturday 3rd April 2010
quotequote all
I have 9" and 10" but in 20" rim size with the same offsets - 45 and they fit but not without taking all the rear lip off and the fronts are very close to the coil over strut but in answer to your question, yes they will go on. smile

boggie

Original Poster:

393 posts

253 months

Saturday 3rd April 2010
quotequote all
S800VXR said:
I have 9" and 10" but in 20" rim size with the same offsets - 45 and they fit but not without taking all the rear lip off and the fronts are very close to the coil over strut but in answer to your question, yes they will go on.


That's good news! When you say "very close to the coil over strut, are you saying you have fitted coilovers or are you referring to the coil on the standard McPhearson?

I was planning on 9x19 fronts and 10x19 rears. What tyre sizes are you running?

Thanks,
B

S800VXR

5,877 posts

231 months

Saturday 3rd April 2010
quotequote all
I had coilovers anyhow and its very close to them, in fact I fitted offset top mounts to move the strut away so I could get a decent camber angle. As for tires, mine are 285/25 and 245/30. If your going to do it I would not recomend 9" on the front!

You could just buy mine!? there for sale.

Boggie

Original Poster:

393 posts

253 months

Saturday 3rd April 2010
quotequote all
Unfortunately I dont have coilovers so your 9" will not fit my struts. Thanks anyway. B

Edited by Boggie on Saturday 3rd April 23:50

S800VXR

5,877 posts

231 months

Sunday 4th April 2010
quotequote all
Boggie said:
Unfortunately I dont have coilovers so your 9" will not fit my struts. Thanks anyway. B

Edited by Boggie on Saturday 3rd April 23:50
No 9" fronts will fit without coilovers Im affraid.