what part to drill out on disc change
what part to drill out on disc change
Author
Discussion

snowwolf

Original Poster:

11,503 posts

206 months

Sunday 4th April 2010
quotequote all
I have heard that you need to drill out a couple of holes each side when changing to the larger VXR discs, does anyone know what part needs drilling and what size hole to drill. need to get all I need to do the job this week.

Any photo's would be handy

motomk

2,188 posts

275 months

Monday 5th April 2010
quotequote all
I am assuming you are fitting the 330x32mm Monaro VXR disc brakes (HSV brakes where I come from) The only thing that needed removing on my old car was the splash guard for the discs on the normal speck car. If it has them fitted, they are only held on with a small rivet that can be chiseled off. I assume you picked up the calipers too? or amended mounting brackets? brake lines too would be needed. other than that, they should bolt on. The bolts to remove the calipers are the same size as the wheel nuts.





Edited by motomk on Monday 5th April 06:55

snowwolf

Original Poster:

11,503 posts

206 months

Monday 5th April 2010
quotequote all
Cheers for that write up, much appreciated, I better take some pics when I do my front and back disc change for us here in the UK

So are you saying that if the VXR calipers that I got with the discs have the mounting bracket on them, I will not need to drill anything?

H15 UTE

76 posts

208 months

Monday 5th April 2010
quotequote all
Hi Snowwolf, I think they will fit straight on, but apparently you may need to enlarge the mounting holes in the bracket by 2mm, maybe you could take a bolt out and see if it goes through the bracket before you start, if it does then it'll be a simple bolt up job with a little fettling to backplate shields. good luck

snowwolf

Original Poster:

11,503 posts

206 months

Monday 5th April 2010
quotequote all
H15 UTE said:
Hi Snowwolf, I think they will fit straight on, but apparently you may need to enlarge the mounting holes in the bracket by 2mm, maybe you could take a bolt out and see if it goes through the bracket before you start, if it does then it'll be a simple bolt up job with a little fettling to backplate shields. good luck smile
Am I assuming that the later VXR had smaller bolts holding them on, is that right?

stigmundfreud

22,454 posts

241 months

Monday 5th April 2010
quotequote all
no drilling required Mick. I had VXR brakes/discs fitted to my cv8 from a 6.0 vxr.

H15 UTE

76 posts

208 months

Monday 5th April 2010
quotequote all
stigmundfreud said:
no drilling required Mick. I had VXR brakes/discs fitted to my cv8 from a 6.0 vxr.


My thoughts too Stiggy, but yours was an 04 where as Mick's is an 05, and according to Rog ala MF in an earlier post asked by Mick the 05s have bigger bolts scratchchin , Only one way to find out......

stigmundfreud

22,454 posts

241 months

Monday 5th April 2010
quotequote all
god bless common sense in the design department!

Bonnie and Clyde

11,701 posts

223 months

Monday 5th April 2010
quotequote all
But the discs on a face life monaro are the same size as the discs on the VXR's. I dont see the point in upgrading them

stigmundfreud

22,454 posts

241 months

Monday 5th April 2010
quotequote all
calipers mel the vxr's use more of the swept area

Bonnie and Clyde

11,701 posts

223 months

Monday 5th April 2010
quotequote all
stigmundfreud said:
calipers mel the vxr's use more of the swept area
Now in English please

crisisjez

9,209 posts

236 months

Monday 5th April 2010
quotequote all
Bonnie and Clyde said:
stigmundfreud said:
calipers mel the vxr's use more of the swept area
Now in English please

They grip the disc better

stigmundfreud

22,454 posts

241 months

Monday 5th April 2010
quotequote all
Bonnie and Clyde said:
stigmundfreud said:
calipers mel the vxr's use more of the swept area
Now in English please;)
the disks may be the same size but the area used by the calipers was different and I believe the vxr#s had bigger pistons.

snowwolf

Original Poster:

11,503 posts

206 months

Monday 5th April 2010
quotequote all
I am 99% sure the discs on my ro are about 285mm,ish across and the discs I will be fitting are 315mm I will have another check tomorrow.