Performance intake question
Performance intake question
Author
Discussion

behold81

Original Poster:

2,931 posts

200 months

Friday 9th April 2010
quotequote all
Anyone got any good articles or comments on the extra power increase you get from running a MAFless system?

I have a 85mm MAF Sensor at present and airbox mod to allow the extra airflow.

Do i need to remove the MAF and put on the direct air feed to try it with out or just unplug and remap as is???

well_fans

4,193 posts

255 months

Friday 9th April 2010
quotequote all
should get away with remap with it in place and unplugged or removed. something at the back of my brain tells me I read an article somewhere about the benefits of leaving it in but disconnected as the mesh helps "shape" the airflow more than it restricts things. Could be talking a load of bollox mind you but might be worth a rummage on some of the LS1 tech forums see what the consensus is.

MyM8V8

9,468 posts

226 months

Friday 9th April 2010
quotequote all
well_fans said:
should get away with remap with it in place and unplugged or removed. something at the back of my brain tells me I read an article somewhere about the benefits of leaving it in but disconnected as the mesh helps "shape" the airflow more than it restricts things. Could be talking a load of bks mind you but might be worth a rummage on some of the LS1 tech forums see what the consensus is.
I think the laminar flow was required to provide a consistant reading over the heated wires (of the MAF).

Kaws LS2 VXR8 was mapped mafless with the maf left in until his Dus OTR arrived. He managed to get into the 12's with that setup.

I'm now running mafless and looking forward to getting some figures at TVR tomorrow. The only figures I can give you are that at the last TR running with maf I made 158.7 MPH ( and a 12.5 1/4)and at the last one running mafless made 165.8 or so with a 12.4 1/4.

Edited by MyM8V8 on Friday 9th April 18:54

behold81

Original Poster:

2,931 posts

200 months

Friday 9th April 2010
quotequote all
was that with no other mods??? between the two??

stigmundfreud

22,454 posts

241 months

Friday 9th April 2010
quotequote all
MAFless, why? If you remove the MAF (connector) depending on model you also lose your IAT sensor too so you need to check on that. If you had a tune tool there are several ways of disabling maf but if you just unplug it you'll get a CEL and the car will fall back on just using the VE table which by default is on LS1's way off. If you want to go mafless you can buy an off the shelf tune like Kaw did or you can tune your ve table yourself.

Going mafless but not removing the MAF is pointless as the restriction to airflow is still there but really you are chasing a few ponies for what? SD for ultimate power tunes but then you need to over time make adjustments thats what the MAF helps to take care of. Want a better feeling to throttle? Disable LTFT and let the O2's just provide STFT and you'll get a much better throttle response.

Seriously chasing a few ponies aint worth it is it? Big power yes but on a standardish car no

stigmundfreud

22,454 posts

241 months

Friday 9th April 2010
quotequote all
behold81 said:
was that with no other mods??? between the two??
be good to know, I suspect it had a bit of a better map applied too inbetween the two events, could removing the maf alone result in an 8mph difference?

behold81

Original Poster:

2,931 posts

200 months

Saturday 10th April 2010
quotequote all
stigmundfreud said:
MAFless, why? If you remove the MAF (connector) depending on model you also lose your IAT sensor too so you need to check on that. If you had a tune tool there are several ways of disabling maf but if you just unplug it you'll get a CEL and the car will fall back on just using the VE table which by default is on LS1's way off. If you want to go mafless you can buy an off the shelf tune like Kaw did or you can tune your ve table yourself.

Going mafless but not removing the MAF is pointless as the restriction to airflow is still there but really you are chasing a few ponies for what? SD for ultimate power tunes but then you need to over time make adjustments thats what the MAF helps to take care of. Want a better feeling to throttle? Disable LTFT and let the O2's just provide STFT and you'll get a much better throttle response.

Seriously chasing a few ponies aint worth it is it? Big power yes but on a standardish car no



Well im looking at remap software to dial in my car even more and for diagnostics. Also with mods as i move forward i can tune it myself.

My intake is opened out bar the TB. with 85mm MAF im bigger than the plenum opening anyway.

Hence the wondering if i remap MAFless whether i will gain any extra. And on top that if i need to get something like the OTRCAI or is it not worth the extra cash given my open intake?

cv8gto

410 posts

204 months

behold81

Original Poster:

2,931 posts

200 months

Saturday 10th April 2010
quotequote all
Thats interesting...

Although (And i could be wrong) the removing of the MAF sensor is to make the maping more accurate as the MAF can give delayed/incorrect results causing a lag/loss in power...

cv8gto

410 posts

204 months

Saturday 10th April 2010
quotequote all
behold81 said:
Thats interesting...

Although (And i could be wrong) the removing of the MAF sensor is to make the maping more accurate as the MAF can give delayed/incorrect results causing a lag/loss in power...



What if it is right in front of the TB,( more info the better maybe) thinking I will pick one of these intakes up and do a write up with a few dyno runs, have a 4inch pipe custome box and K & N filter setup currently, will be interesting to run the diff setups, may even pull old standard back out.

behold81

Original Poster:

2,931 posts

200 months

Saturday 10th April 2010
quotequote all
So you need the following....

Standard
MAF with intake
MAF less with same intake.

Be interesting results....

cv8gto

410 posts

204 months

Saturday 10th April 2010
quotequote all
behold81 said:
So you need the following....

Standard
MAF with intake
MAF less with same intake.

Be interesting results....


I will order the intake tomorrow (who knows when it will get to Sweden) and download a MAFLESS tune. Now to find a local DYNO thats not full of Volvo's.

Will keep u updated.

drew ss

2,683 posts

215 months

Saturday 10th April 2010
quotequote all
theres thousands of mafless tunes running around aus so there m,ust be somethin there

behold81

Original Poster:

2,931 posts

200 months

Saturday 10th April 2010
quotequote all
drew ss said:
theres thousands of mafless tunes running around aus so there m,ust be somethin there


From what i have read is by only using the MAP sensor you get a more accurate reading.

stigmundfreud

22,454 posts

241 months

Saturday 10th April 2010
quotequote all
drew ss said:
theres thousands of mafless tunes running around aus so there m,ust be somethin there
yes a standard consistent climate and a constant atmospheric range

Vez

239 posts

289 months

Sunday 11th April 2010
quotequote all
Excuse my ignorance, but the vehicle has a map sensor so I dont really see the issue. Previous vehicles I have owned many have dropped the MAF, in favour of a MAP sensor, many tuners prefer tuning MAP than MAF and get far better results. IMHO the MAF is only there to correct lazy mapping, ala your example of the standard LS2 tables.

ferb

3,112 posts

241 months

Sunday 11th April 2010
quotequote all
stigmundfreud said:
drew ss said:
theres thousands of mafless tunes running around aus so there m,ust be somethin there


yes a standard consistent climate and a constant atmospheric range

Never had any problems with my ute being maffless tuned.

behold81

Original Poster:

2,931 posts

200 months

Sunday 11th April 2010
quotequote all
Vez said:
Excuse my ignorance, but the vehicle has a map sensor so I dont really see the issue. Previous vehicles I have owned many have dropped the MAF, in favour of a MAP sensor, many tuners prefer tuning MAP than MAF and get far better results. IMHO the MAF is only there to correct lazy mapping, ala your example of the standard LS2 tables.


Glad someone is on my wavelength....

ringram

14,702 posts

279 months

Sunday 11th April 2010
quotequote all
stigmundfreud said:
drew ss said:
theres thousands of mafless tunes running around aus so there m,ust be somethin there
yes a standard consistent climate and a constant atmospheric range
Toilet.

MAP = Pressure IAT = Temperature so why doesnt mafless work 100%? If you cover both aspects youspeak of!?

Answer = pathetic feeble tuning efforts.

MAF vs Mafless with the right diameter MAF meter will be zero power difference.

But MAF does not measure airflow in a linear manner, its a geometric curve, so only midrange is it most accurate, at low and high airflow it looses resolution. Mafless works well off throttle at low airflow. You get a more responsive vehicle. OEM ECU's do not use the maf 100% at low airflow settings. MAF is only 100% used over 4000rpm in the OEM tune.

ringram

14,702 posts

279 months

Sunday 11th April 2010
quotequote all
Vez said:
Excuse my ignorance, but the vehicle has a map sensor so I dont really see the issue. Previous vehicles I have owned many have dropped the MAF, in favour of a MAP sensor, many tuners prefer tuning MAP than MAF and get far better results. IMHO the MAF is only there to correct lazy mapping, ala your example of the standard LS2 tables.
Amen Jesus wink