Clutch problem in 6th gear
Discussion
Hi Guys,
Was out in the Ro today and noticed that when i changed from 5th to 6th when i accelerated the car just kept reving and i had no power to the wheels, this lasted about 3 secs then engine engaged and normal drive resumed.
Happend 5 times or so, any ideas what this could be, NB changed the clutch fluid about two weeks ago as it was black, not sure if this could be something to do with it.
TIA
Was out in the Ro today and noticed that when i changed from 5th to 6th when i accelerated the car just kept reving and i had no power to the wheels, this lasted about 3 secs then engine engaged and normal drive resumed.
Happend 5 times or so, any ideas what this could be, NB changed the clutch fluid about two weeks ago as it was black, not sure if this could be something to do with it.
TIA
stevieturbo said:
Does sound like clutch slippage. Odd that it only happens in one gear though.
Suppose it depends how th OP drives - more force in the higher gears unless doing illegal speeds when changing.
Last car I had with clutch slippage, I had to keep changing down untill it "bit", so quite probable in the highest gear?
Wolfracer said:
stevieturbo said:
Does sound like clutch slippage. Odd that it only happens in one gear though.
Suppose it depends how th OP drives - more force in the higher gears unless doing illegal speeds when changing. Last car I had with clutch slippage, I had to keep changing down untill it "bit", so quite probable in the highest gear?
Usually if your in 6th it will be very low rpm, and not that much torque. If the clutch was to let go..I'd expect a lower gear...say 3rd or 4th. Still a tall gear, but you'll be pulling more revs, and more torque ususally.
As for milage. There is no set milage for a clutch to last. The wrong driver could destroy a clutch in a day. The right driver could make it last 200k
maxmc2 said:
Hi Guys,
Was out in the Ro today and noticed that when I changed from 5th to 6th when I accelerated the car just kept revving and I had no power to the wheels, this lasted about 3 secs then engine engaged and normal drive resumed.
Happened 5 times or so, any ideas what this could be, NB changed the clutch fluid about two weeks ago as it was black, not sure if this could be something to do with it.
TIA
Was out in the Ro today and noticed that when I changed from 5th to 6th when I accelerated the car just kept revving and I had no power to the wheels, this lasted about 3 secs then engine engaged and normal drive resumed.
Happened 5 times or so, any ideas what this could be, NB changed the clutch fluid about two weeks ago as it was black, not sure if this could be something to do with it.
TIA
You say it returned to normal, i.e. full load could be applied in the lower gears OK without slippage?
Sounds weird like the pressure plate jamming. It does have a self adjusting mechanism for ware compensation.
38K is very low for the clutch to be worn. I changed mine at 24K due to a judder problem and it was difficult to see any ware at all in the friction disk compared to the new one, such as thickness reduction.
I'm on my 4th clutch in only 24k miles. Finding one that works at higher torque is difficult. Up to 700lbs I would recommend the spec II as it has stock feel and clamps really well. The syptoms you describe are just a worn clutch, mine has only ever slipped in 5th or 6th but it's also supercharged.
broadslide said:
Similar symptons with mine but would also slip in 4th and 5th at 5-6000 rpm and then clutch pedal would go hard for a few seconds. Changing the clutch for an LS7 last week and found the rear crankshaft oil seal was weeping. Might be worth checking. Normal driving was fine.
Hello Charlie, how you feeling
crisisjez said:
broadslide said:
Similar symptons with mine but would also slip in 4th and 5th at 5-6000 rpm and then clutch pedal would go hard for a few seconds. Changing the clutch for an LS7 last week and found the rear crankshaft oil seal was weeping. Might be worth checking. Normal driving was fine.
Hello Charlie, how you feeling

broadslide said:
crisisjez said:
broadslide said:
Similar symptons with mine but would also slip in 4th and 5th at 5-6000 rpm and then clutch pedal would go hard for a few seconds. Changing the clutch for an LS7 last week and found the rear crankshaft oil seal was weeping. Might be worth checking. Normal driving was fine.
Hello Charlie, how you feeling
Hi Jez Yeah I'm really good thanks. Everything going to plan only have to go back to hospital for routine check ups every fortnight now. Looking forward to TR in October. Having to use my old Chevy stepside as a daily driver while the Ro gets a new clutch and oil seal. Non servo drums all round makes you read the road ahead after AP's

I should Benny
You be careful something doesn't burst.
Hope to see you before Oct, maybe I'll do a barby and get everyone over to prod your scars

wormus said:
I'm on my 4th clutch in only 24k miles. Finding one that works at higher torque is difficult. Up to 700lbs I would recommend the spec II as it has stock feel and clamps really well. The symptoms you describe are just a worn clutch, mine has only ever slipped in 5th or 6th but it's also supercharged.
Clearly that is a design/application problem. I have had my clutch slip once in first and was fine before and after. I believe this was due to a runaway burning problem akin to brake fade. Almost a self protecting mechanism. With 400 BHP + (some out there +++)then it is very easy to cook the friction disk and mating surfaces which have relatively small area. Clearly multiplate as was posted the other day or a wet design to take the heat away are required.
When God created the V8 engine he looked down upon it and saw that it was good. Then he created the perfect companion, the hydrokinetic fluid torque converter.
Gassing Station | HSV & Monaro | Top of Page | What's New | My Stuff





