How do you lower the compression ratio of an engine?
Discussion
After discussing a few bits with the local engine place that im wanting doing yet again lower the compression ratio got mentioned, I breezed over that conversation as to be honest have not got a bloody clue what im talking about!
Tried looking on net but cant really see an actual answer so how do you actually lower the compression ratio of an LS engine?
Is it a complete re-build job or something much more simple to do!?
Tried looking on net but cant really see an actual answer so how do you actually lower the compression ratio of an LS engine?
Is it a complete re-build job or something much more simple to do!?
I've used 317's on builds. Basically an ls6 head but with big chambers and stock valves ie not hollow. Ideally you want a head that has a chamber diameter the same as your bore diameter. Looking at the aftermarket stuff you'll see that different chamber sizes are offerred. If using decent boost the proper way would be bowled forged pistons (try to keep the quench pad though)and a rebalance of the crankshaft if the piston weights are different to your original items.
The piston on the right is a very good design but is a custom made item.

The piston on the right is a very good design but is a custom made item.

Best way is dished pistons other ways are spacer plates and 2 head gaskets, skim the pistons (not a good idea with standard lsx pistons though) or even shorter con rods (as in nobles) there are other ways but these are the ways i have dealt with in the past and tbh all have been reliable 

As im running FI and it keeps coming up in conversations about where to go next with the car, its not a definate thing to do just an idea that as I say keeps appearing and im wanting to look into it a bit more before make any decisions.
Would rather research a number of avenues before take the plunge and regret it!
Would rather research a number of avenues before take the plunge and regret it!
stigmundfreud said:
the only real best way is the pistons anything else is a comprimise.
Many would say adjusting cylinder head chamber size is the best way, not alwys the easiest though.There is little wrong with using different gasket thickness to adjust CR, but the scope for adjustment is quite small. With modern steel shim gaskets, its little different than skimming lots off a head to increase CR.
Easiest cheapest option is to drill a hole in the pistons. Might run a bit funny after though

stevieturbo said:
stigmundfreud said:
the only real best way is the pistons anything else is a comprimise.
Many would say adjusting cylinder head chamber size is the best way, not alwys the easiest though.
There is little wrong with using different gasket thickness to adjust CR, but the scope for adjustment is quite small. With modern steel shim gaskets, its little different than skimming lots off a head to increase CR.
Easiest cheapest option is to drill a hole in the pistons. Might run a bit funny after though

Is that just one at a time till the result is desired??? LOL
[quote=stevieturbo
There is little wrong with using different gasket thickness to adjust CR, but the scope for adjustment is quite small. With modern steel shim gaskets, its little different than skimming lots off a head to increase CR.
[/quote]
Except you change the squish clearance, which might be quite important for a given application.
There is little wrong with using different gasket thickness to adjust CR, but the scope for adjustment is quite small. With modern steel shim gaskets, its little different than skimming lots off a head to increase CR.
[/quote]
Except you change the squish clearance, which might be quite important for a given application.
ringram said:
If your pistons are stock now, then replacing them with dished ones is a no brainer.
Yeah its starting to look that way!
Im definately going to change the heads when the car goes in for the next round of mods, been trying to avoid doing them and should have done them at the same time as the cam last year but given in and going to order some when (if) the exchange rate alters a bit.
Thats what I thought, but still seems a stange way to get reliability. I would have thought that reducing the compresion ratio reduces the available power, and that to significantly reduce the compression ration would cost a lot of money because of the work involved. If it needs new pistons etc, then why not get the proper uprated jobbies? Is there that much difference in cost/reliability?
Gassing Station | HSV & Monaro | Top of Page | What's New | My Stuff



