Discussion
Hi all,
Is it possible to fit 19x9 ET48 front wheels with 235/35/19 on a car with standard struts but using spacers (10mm / 15mm?)?
On the rear will 19x10 ET45 with 265/30/19 fit?
Some months ago I found a forum thread where lots of Monaro owners posted their experiences with all sorts of wheel and tyre combinations, it they worked and if not why etc. Buggered if I can find it now and can't recall if it was here, on the LS1GTO or Aussie forums. Can anyone help me find it again as I spent most of this afternoon searching to no avail.
Many thanks
B
Is it possible to fit 19x9 ET48 front wheels with 235/35/19 on a car with standard struts but using spacers (10mm / 15mm?)?
On the rear will 19x10 ET45 with 265/30/19 fit?
Some months ago I found a forum thread where lots of Monaro owners posted their experiences with all sorts of wheel and tyre combinations, it they worked and if not why etc. Buggered if I can find it now and can't recall if it was here, on the LS1GTO or Aussie forums. Can anyone help me find it again as I spent most of this afternoon searching to no avail.
Many thanks
B
gsd2000 said:
I would go 8.5" on a 50 offset with a 255 tyre, thats what i have and everything looks okay but ive checked to the bumpstops
Thanks for the alternative but I have been offered the actual wheels / tyres combo above for a good price. I don't know if they will fit and it is a 400 mile round trip to check. Would not have been too bad if the LPG installation was useably mapped yet but using £1.30 every 4 miles makes it £130 to try them on for size!
Cheers,
B
They won't fit my friend. I have 8.5" on the rear with a 45 offset and the wheel catches the arch on full travel. I can get around this by grinding the arch lip back but a 10" wide wheel would hit even after doing that.
9" with spacers on the front would see the tyre rubbing the arch liner on full lock - not only that they would stick out from the wing a fair bit.
9" with spacers on the front would see the tyre rubbing the arch liner on full lock - not only that they would stick out from the wing a fair bit.
Trampy said:
They won't fit my friend. I have 8.5" on the rear with a 45 offset and the wheel catches the arch on full travel. I can get around this by grinding the arch lip back but a 10" wide wheel would hit even after doing that.
9" with spacers on the front would see the tyre rubbing the arch liner on full lock - not only that they would stick out from the wing a fair bit.
9" with spacers on the front would see the tyre rubbing the arch liner on full lock - not only that they would stick out from the wing a fair bit.
What tyre size are you running on the back?
Trampy said:
They won't fit my friend. I have 8.5" on the rear with a 45 offset and the wheel catches the arch on full travel. I can get around this by grinding the arch lip back but a 10" wide wheel would hit even after doing that.
9" with spacers on the front would see the tyre rubbing the arch liner on full lock - not only that they would stick out from the wing a fair bit.
9" with spacers on the front would see the tyre rubbing the arch liner on full lock - not only that they would stick out from the wing a fair bit.
Thanks Trampy,
Bugger. Ideally I want to fit 19" rims with 235 fronts and 265+ rears but it seems the Monaro was designed to only take Mondeo sized rubber. :-(
Anyone have any other suggestions?
Cheers
Hmmm, interesting. Do you find they fit OK, perform OK and don't wear in the middle? IIRC the maximum tyre width for 8J rims is 235 or 245 (depending upon manufacturer) and even then, that is pushing it. But I like the sound of 255s!
As a rough check, I have just pushed a large lump of Blutak between my rims and the strut, there is 13mm clearance. If I bought these 19x9 ET48 rims (standard rims are 18x8 Et48) there should be, in theory, 0.5mm clearance remaining. Alloy wheels do not flex so clearance IS clearance but 0.5 is pretty damn close. I am tempted to go and try them. If the fronts fit on the CV8 then I could buy 2 sets of fronts and put a set on the rear.
Any thoughts?
B
As a rough check, I have just pushed a large lump of Blutak between my rims and the strut, there is 13mm clearance. If I bought these 19x9 ET48 rims (standard rims are 18x8 Et48) there should be, in theory, 0.5mm clearance remaining. Alloy wheels do not flex so clearance IS clearance but 0.5 is pretty damn close. I am tempted to go and try them. If the fronts fit on the CV8 then I could buy 2 sets of fronts and put a set on the rear.
Any thoughts?
B
boggie said:
Hmmm, interesting. Do you find they fit OK, perform OK and don't wear in the middle? IIRC the maximum tyre width for 8J rims is 235 or 245 (depending upon manufacturer) and even then, that is pushing it. But I like the sound of 255s!
As a rough check, I have just pushed a large lump of Blutak between my rims and the strut, there is 13mm clearance. If I bought these 19x9 ET48 rims (standard rims are 18x8 Et48) there should be, in theory, 0.5mm clearance remaining. Alloy wheels do not flex so clearance IS clearance but 0.5 is pretty damn close. I am tempted to go and try them. If the fronts fit on the CV8 then I could buy 2 sets of fronts and put a set on the rear.
Any thoughts?
B
Yea! thats not enough clearence. Remember the suspension will flex so you want at least 5mm clearence. You could just fit a thin spacer plate TBH. Anything over 8.5 will mean you need to remove the rear lip though!As a rough check, I have just pushed a large lump of Blutak between my rims and the strut, there is 13mm clearance. If I bought these 19x9 ET48 rims (standard rims are 18x8 Et48) there should be, in theory, 0.5mm clearance remaining. Alloy wheels do not flex so clearance IS clearance but 0.5 is pretty damn close. I am tempted to go and try them. If the fronts fit on the CV8 then I could buy 2 sets of fronts and put a set on the rear.
Any thoughts?
B
Gassing Station | HSV & Monaro | Top of Page | What's New | My Stuff


