Will this Cam be too extreme?
Discussion
My current cam is the following spec:
Duration at 050 inch Lift 212 int./218 exh.
Advertised Duration 265 int./271 exh.
Intake Valve Lift with Factory Rocker Arm Ratio 0.558 in.
Lobe Separation (degrees) 115
However im wanting to increase top end rpm power by quite a decent amount and also go for a better FI cam, have been recommended this one what do you think:
Duration at 050 inch Lift 239 int./243 exh.
Advertised Duration 289 int./293 exh.
Intake Valve Lift with Factory Rocker Arm Ratio 0.624 in.
Lobe Separation (degrees) 114
?? Cheers
Duration at 050 inch Lift 212 int./218 exh.
Advertised Duration 265 int./271 exh.
Intake Valve Lift with Factory Rocker Arm Ratio 0.558 in.
Lobe Separation (degrees) 115
However im wanting to increase top end rpm power by quite a decent amount and also go for a better FI cam, have been recommended this one what do you think:
Duration at 050 inch Lift 239 int./243 exh.
Advertised Duration 289 int./293 exh.
Intake Valve Lift with Factory Rocker Arm Ratio 0.624 in.
Lobe Separation (degrees) 114
?? Cheers
after_shock said:
Had a feeling it would be, still not sure what numbers im looking at but thought it might be a bit big, is it too big tho!?
Im going to change the heads at the same time when do it this year as opposed to just changing the cam itself.
Im going to change the heads at the same time when do it this year as opposed to just changing the cam itself.
Iam got a 223 cam and thats bigish
if u type ur cam into u-tube u will get an idea of its idal and being reved u might even get a dyno car with the cam fitted.
im no cam expert but i would have thought that on an ls2 to keep emissions legal you would want to stay below 230, i think blowers like a wide duration split aswell, and a fairly high LSA. Again im only going by what i have picked up over the internet so i could be wrong.
I would try to speak to a cam specialist and tell them your spec and get a custom grind.
I would try to speak to a cam specialist and tell them your spec and get a custom grind.
Hmm, In an LS2 Id be looking at 224/232-115 or similar that "should" be close to passing. Its basically what Gareth has in his now and his passed. There are a few blower cams around, just check out the specs and find something with the intake in the low 220 range.
If you go bigger emissions will fail and fuel economy will start to be noticeably bad.
If you go bigger emissions will fail and fuel economy will start to be noticeably bad.
Would do no harm to ask the likes of Lingenfelter. They would have plenty of experience, and offer a range of camshafts. Seeing as they offer full drive in drive out packages tnhat would need to meet all sorts of emissions criteria in the US, they would have plenty of experience
Interesting choice here.... even better considering the price
http://www.lingenfelter.com/mm5/merchant.mvc?Scree...
Or this....
massive split, very wide LSA, and monster lift !!
http://www.lingenfelter.com/mm5/merchant.mvc?Scree...
They still say it has a smooth idle though, which is a good sign for emissions etc
Interesting choice here.... even better considering the price
http://www.lingenfelter.com/mm5/merchant.mvc?Scree...
Or this....
massive split, very wide LSA, and monster lift !!
http://www.lingenfelter.com/mm5/merchant.mvc?Scree...
They still say it has a smooth idle though, which is a good sign for emissions etc
[quote=stevieturbo]If you read...they have actually discontinued their GT7, due to its similarity to the LS9 cam
They now just sell it in its place...which is some $200 cheaper.[/quote
I only read the cam spec's
But yeah, the GM cam is a bargain then! Designed to meet emissions..
Its actually an LS7 cam IIRC. LS7=LS9 cam. Lift is different due to rocker ratio.
They now just sell it in its place...which is some $200 cheaper.[/quote
I only read the cam spec'sBut yeah, the GM cam is a bargain then! Designed to meet emissions..
Its actually an LS7 cam IIRC. LS7=LS9 cam. Lift is different due to rocker ratio.
If anyones after an LS9 cam I will have one coming out of my engine later this year, only done a couple of thousand miles by then.
O.k I will E-mail Lingenfelter see what they come up with.
The big one above was recommended as a blower cam!
The main criteria is that the power band is moved higher up the rev range so no idea what to look out for in that respect.
Fuel economy im not too fussed about as dont use the car very often, emissions however I do need something that will pass (well actually I dont but it does always help) The idle needs to be usuable though.
O.k I will E-mail Lingenfelter see what they come up with.
The big one above was recommended as a blower cam!
The main criteria is that the power band is moved higher up the rev range so no idea what to look out for in that respect.
Fuel economy im not too fussed about as dont use the car very often, emissions however I do need something that will pass (well actually I dont but it does always help) The idle needs to be usuable though.
MadMaxHSV said:
ringram said:
The first one is almost an LS9 cam.... which is what Piers fitted to his...
So far can only say it idles fine. Let you know how it fairs...
If its very similar spec to mine the idle will be just like normal, or almost. Top end power will fade away quite sharply though, although you are running a better charger with more boost than me so you probably wont notice!
Mid range is excellent with it though.
Let me know what you think of your new clutch if you dont mind!?
Gassing Station | HSV & Monaro | Top of Page | What's New | My Stuff



wonder how well it works in an n/a ls1?