Changing clutch resevoir fluid
Changing clutch resevoir fluid
Author
Discussion

snowwolf

Original Poster:

11,503 posts

206 months

Friday 21st May 2010
quotequote all
Have changed my clutch fluid every month for last 6 months and it is always black and really contaminated each time.
I have found that the small plastic water bottles are ideal, takes a second to completly empty the vessel with one queeze biggrin

As you can see in the pics, it gets very dirty really quickly, its got to be clutch dust!






essexhsv

792 posts

229 months

Saturday 22nd May 2010
quotequote all
Yes it is clutch dust that gets past the thrust bearing seal then floats to the top.

I clean mine out every week seeing as it only takes like 30 seconds to do.

check this link out

www.rangeracceleration.com/Clutch_Care.html

drew ss

2,683 posts

215 months

Saturday 22nd May 2010
quotequote all
so can u actually drain all the fluid from the res and not get air in it

Big Russ

53 posts

202 months

Saturday 22nd May 2010
quotequote all
i don't understand how clutch dust can pass the seal, but clutch fluid doesn't! Surely if dust can pass on way then clutch fluid can pass the other, however no fluid loss????????????????

S800VXR

5,877 posts

231 months

Saturday 22nd May 2010
quotequote all
Big Russ said:
i don't understand how clutch dust can pass the seal, but clutch fluid doesn't! Surely if dust can pass on way then clutch fluid can pass the other, however no fluid loss????????????????
Yawn........ of all the subject discussed on here this one is by far the most boring now! As our main man says above, if dust can get in then sure as the sun will rise tomorrow the fluid will get out first! common bloody sense! rolleyes

With a radial design release slave it A. Has a greater area to obsorb heat and as such B. The fluid boils and goes black/causes clutch release issues.


THE ONLY WAY TO SOLVE THIS IS TO GET A REMOTE BLEEDER FITTED SO YOU CAN FLUSH THROUGH THE WHOLE SYSTEM ON A REGULAR BASIS.... just like I have on mine, pictures soon when I get it back next weekend.

gsd2000

11,515 posts

214 months

Saturday 22nd May 2010
quotequote all
S800VXR said:
Big Russ said:
i don't understand how clutch dust can pass the seal, but clutch fluid doesn't! Surely if dust can pass on way then clutch fluid can pass the other, however no fluid loss????????????????
Yawn........ of all the subject discussed on here this one is by far the most boring now! As our main man says above, if dust can get in then sure as the sun will rise tomorrow the fluid will get out first! common bloody sense! rolleyes

With a radial design release slave it A. Has a greater area to obsorb heat and as such B. The fluid boils and goes black/causes clutch release issues.


THE ONLY WAY TO SOLVE THIS IS TO GET A REMOTE BLEEDER FITTED SO YOU CAN FLUSH THROUGH THE WHOLE SYSTEM ON A REGULAR BASIS.... just like I have on mine, pictures soon when I get it back next weekend.
or not bother with a remote bleeder and struggle hehe

Big Russ

53 posts

202 months

Saturday 22nd May 2010
quotequote all
wrong time of the month mate!!!

S800VXR

5,877 posts

231 months

Saturday 22nd May 2010
quotequote all
Big Russ said:
wrong time of the month mate!!!
LOL! Na, her not me. Just bored listening to all the rubbish said about this issue. The cars are brill but the clutch design sucks!! hence me insisting on a remote bleed point being fitted under the bonnet in easy reach so I can regular flush the system with new. First time I had an issue with my clutch I thought Id broken it!

stigmundfreud

22,454 posts

241 months

Saturday 22nd May 2010
quotequote all
S800VXR said:
Big Russ said:
i don't understand how clutch dust can pass the seal, but clutch fluid doesn't! Surely if dust can pass on way then clutch fluid can pass the other, however no fluid loss????????????????
Yawn........ of all the subject discussed on here this one is by far the most boring now! As our main man says above, if dust can get in then sure as the sun will rise tomorrow the fluid will get out first! common bloody sense! rolleyes

With a radial design release slave it A. Has a greater area to obsorb heat and as such B. The fluid boils and goes black/causes clutch release issues.


THE ONLY WAY TO SOLVE THIS IS TO GET A REMOTE BLEEDER FITTED SO YOU CAN FLUSH THROUGH THE WHOLE SYSTEM ON A REGULAR BASIS.... just like I have on mine, pictures soon when I get it back next weekend.
next weekend? Thougth it was this weekend?

PS you can bleed most of it through this way but it takes a lot of fluid and its not thorough

Big Russ

53 posts

202 months

Saturday 22nd May 2010
quotequote all
Does the fish recommend/fit this remote bleed point. The fish knows best!!

stigmundfreud

22,454 posts

241 months

Saturday 22nd May 2010
quotequote all
Big Russ said:
Does the fish recommend/fit this remote bleed point. The fish knows best!!
actually granada2808902829382100857279372 knows best when it comes to this

SimonV8ster

13,039 posts

259 months

Saturday 22nd May 2010
quotequote all
Big Russ said:
Does the fish recommend/fit this remote bleed point. The fish knows best!!
Even if they don't they probably wish we all had it as it would save them hours !!

dazerc

427 posts

238 months

Saturday 22nd May 2010
quotequote all
[quote=stigmundfreud
you can bleed most of it through this way but it takes a lot of fluid and its not thorough
[/quote]

Whats the best way to replace the clutch fluid as I just looked at mine and its black. car has only done 5000 miles

gsd2000

11,515 posts

214 months

Saturday 22nd May 2010
quotequote all
dazerc said:
[quote=stigmundfreud
you can bleed most of it through this way but it takes a lot of fluid and its not thorough
Whats the best way to replace the clutch fluid as I just looked at mine and its black. car has only done 5000 miles
proper bleed using the bleed nipple on the gearbox, its a bit of a pain to get to and you can really see it but you can feel it

granada203028

1,500 posts

228 months

Saturday 22nd May 2010
quotequote all
The fluid does not boil. The slave cylinder is well heatsinked to the front of the gearbox. The heat path from the friction surface to it is long and torturous including the bearing and plastic parts. It is very diffarent to brake callipers where more heat is generated and the cylinder is just behind the pad. Dot 5.1 boils at 270 deg C!

I notice my clutch effort goes up and down. It is lighter after the car has been left for a few days, apart from the very first application per drive. I think fluid does perhaps seep out slighty and lubricates the exposed travel. So you would expect dust to stick to it and some be pulled back past the seal. After long periods of town driving the clutch gets heaver, presumably because this film does evaporate.

stevieturbo

18,106 posts

278 months

Saturday 22nd May 2010
quotequote all
And I think most DOT 4 fluid is rated at near 300degC


Although I never randomly bleed mine or change the reservoir. Havent even looked to see what colour the fluid is...probably boggin !

dazerc

427 posts

238 months

Saturday 22nd May 2010
quotequote all
stevieturbo said:
And I think most DOT 4 fluid is rated at near 300degC


Although I never randomly bleed mine or change the reservoir. Havent even looked to see what colour the fluid is...probably boggin !
http://www.seinesystems.com/BrakeFluids.htm Lots of different brake/clutch fluids and their boiling points

snowwolf

Original Poster:

11,503 posts

206 months

Saturday 22nd May 2010
quotequote all
I think the problem is there is no dust seal on the actuating rod and as the seal to stop oil gettting out, the chevron of the seal can allow the small particles of clutch dust/grime on the rod to pass the easy route past the seal and then its easy for it to float up to the resevoir.

I just change the reservoir oil every 800 miles or so, very simple and takes a few mins to do, even if you bleed the system at the bottom end, in 800 miles it will be black again.