Anyone used Arch Enemies?
Discussion
Hi All,
I have been trying rime this weekend and have come across a set of BMW X5 19x9 ET48 and 19x10 ET45 rims with 245/35 fronts and 265/30 rears. With a 5mm spacer the fronts will clear the strut by 3 or 4mm. The rear rims will easily clear on their inside as there is around 30mm clearance with the standard 8J ET48 rims. The outside of both front and rear is where I am going to experience difficulties. On the front the outside edge will be 17.5mm further out than standard and the rears will be 18mm. So, Ideally I would like to roll the rear arch return edge and slightly flare the fronts.
I have been talking to a guy who used Arch Enemies to roll and slightly flare his rear arches. He said they did this for £75 using a hot air gun and an arch rolling machine. The results gave him an extra 20mm and there was no paint damage, they even removed and extended his arch liners to fit for an extra tenner. I would also consider getting a more serious flare to the rear wheel arches, perhaps 50mm or more, fitting 12" rims and repainting. Maybe in the future. Has any of you experienced their work first hand?
I have been trying rime this weekend and have come across a set of BMW X5 19x9 ET48 and 19x10 ET45 rims with 245/35 fronts and 265/30 rears. With a 5mm spacer the fronts will clear the strut by 3 or 4mm. The rear rims will easily clear on their inside as there is around 30mm clearance with the standard 8J ET48 rims. The outside of both front and rear is where I am going to experience difficulties. On the front the outside edge will be 17.5mm further out than standard and the rears will be 18mm. So, Ideally I would like to roll the rear arch return edge and slightly flare the fronts.
I have been talking to a guy who used Arch Enemies to roll and slightly flare his rear arches. He said they did this for £75 using a hot air gun and an arch rolling machine. The results gave him an extra 20mm and there was no paint damage, they even removed and extended his arch liners to fit for an extra tenner. I would also consider getting a more serious flare to the rear wheel arches, perhaps 50mm or more, fitting 12" rims and repainting. Maybe in the future. Has any of you experienced their work first hand?
Yes - used him. He is very carefull but the Ro arches will not roll enough without damaging the outside metal which then means you will need to have bodywork done. Also if you want to fit 10" rims you WILL need to have the lips roilled totally flat! been there done that! 
The jap cars he deos have thin single skin metal which rolls easy, the RO has multiple layers which are spot welded together so very strong! You have been warned!

The jap cars he deos have thin single skin metal which rolls easy, the RO has multiple layers which are spot welded together so very strong! You have been warned!
S800VXR said:
Yes - used him. He is very carefull but the Ro arches will not roll enough without damaging the outside metal which then means you will need to have bodywork done. Also if you want to fit 10" rims you WILL need to have the lips roilled totally flat! been there done that!
The jap cars he deos have thin single skin metal which rolls easy, the RO has multiple layers which are spot welded together so very strong! You have been warned!
The jap cars he deos have thin single skin metal which rolls easy, the RO has multiple layers which are spot welded together so very strong! You have been warned!
Thanks! If I were instead to fit 9" ET48 rears with 265/30 tyres, do you think I would need to roll the rears so much that it would involve paint?
Thanks,
B
boggie said:
S800VXR said:
Yes - used him. He is very carefull but the Ro arches will not roll enough without damaging the outside metal which then means you will need to have bodywork done. Also if you want to fit 10" rims you WILL need to have the lips roilled totally flat! been there done that! 
The jap cars he deos have thin single skin metal which rolls easy, the RO has multiple layers which are spot welded together so very strong! You have been warned!
Thanks! If I were instead to fit 9" ET48 rears with 265/30 tyres, do you think I would need to roll the rears so much that it would involve paint?
The jap cars he deos have thin single skin metal which rolls easy, the RO has multiple layers which are spot welded together so very strong! You have been warned!
Thanks,
B
the_ferret82 said:
boggie said:
S800VXR said:
Yes - used him. He is very carefull but the Ro arches will not roll enough without damaging the outside metal which then means you will need to have bodywork done. Also if you want to fit 10" rims you WILL need to have the lips roilled totally flat! been there done that! 
The jap cars he deos have thin single skin metal which rolls easy, the RO has multiple layers which are spot welded together so very strong! You have been warned!
Thanks! If I were instead to fit 9" ET48 rears with 265/30 tyres, do you think I would need to roll the rears so much that it would involve paint?
The jap cars he deos have thin single skin metal which rolls easy, the RO has multiple layers which are spot welded together so very strong! You have been warned!
Thanks,
B
fish did mine 
Edited by 007 VXR on Monday 24th May 09:59
I guess it is a fair price but I quite like the idea of flaring the rear arches if it is possible. THe worse case scenario would be some minor bodywork and rear quarter repaint. This would be a lot cheaper than tubbing and might look rather good too, especially filled with 19x10 rims and 285/30 rubber....
boggie said:
S800VXR said:
Yes - used him. He is very carefull but the Ro arches will not roll enough without damaging the outside metal which then means you will need to have bodywork done. Also if you want to fit 10" rims you WILL need to have the lips roilled totally flat! been there done that! 
The jap cars he deos have thin single skin metal which rolls easy, the RO has multiple layers which are spot welded together so very strong! You have been warned!
Thanks! If I were instead to fit 9" ET48 rears with 265/30 tyres, do you think I would need to roll the rears so much that it would involve paint?
The jap cars he deos have thin single skin metal which rolls easy, the RO has multiple layers which are spot welded together so very strong! You have been warned!
Thanks,
B
See here for thread - http://www.pistonheads.com/gassing/topic.asp?h=0&a...
Hmmm. Very interesting, thanks!
Do you happen to know what extra room he got? I would imagine the fronts, being single skin, will be easy to flare slightly without paint damage. What I might do on the rears is get them to just roll the lip, if the paint gets damaged then go for a nice flare too.
Do you happen to know what extra room he got? I would imagine the fronts, being single skin, will be easy to flare slightly without paint damage. What I might do on the rears is get them to just roll the lip, if the paint gets damaged then go for a nice flare too.
Someone else has used AE but they only rolled the lips a little. If you want 10" on the rear (Bonnie!
) then you need to role totally flat! I also thought about flaring but the rears just to thick, you could stretch it a little as I did but in the end you will just start buckling the outter skin. The fronts dont need flaring, 9" will go on if your carefull.
9.5" will go out back I think with a little roll and the right offset, something around the 50 mark id guess, Tubbing whilst nice is really pointless IMHO unless you really want VXR8 wheels (big offset) and even then you could simply fit spacers to move the wheel out into the available space. If you do tub though I know the fish do a superb job from what Ive seen.
) then you need to role totally flat! I also thought about flaring but the rears just to thick, you could stretch it a little as I did but in the end you will just start buckling the outter skin. The fronts dont need flaring, 9" will go on if your carefull. 9.5" will go out back I think with a little roll and the right offset, something around the 50 mark id guess, Tubbing whilst nice is really pointless IMHO unless you really want VXR8 wheels (big offset) and even then you could simply fit spacers to move the wheel out into the available space. If you do tub though I know the fish do a superb job from what Ive seen.
Magic919 said:
boggie said:
S800VXR said:
Yes - used him. He is very carefull but the Ro arches will not roll enough without damaging the outside metal which then means you will need to have bodywork done. Also if you want to fit 10" rims you WILL need to have the lips roilled totally flat! been there done that! 
The jap cars he deos have thin single skin metal which rolls easy, the RO has multiple layers which are spot welded together so very strong! You have been warned!
Thanks! If I were instead to fit 9" ET48 rears with 265/30 tyres, do you think I would need to roll the rears so much that it would involve paint?
The jap cars he deos have thin single skin metal which rolls easy, the RO has multiple layers which are spot welded together so very strong! You have been warned!
Thanks,
B
See here for thread - http://www.pistonheads.com/gassing/topic.asp?h=0&a...
Gassing Station | HSV & Monaro | Top of Page | What's New | My Stuff


