Discussion
stigmundfreud said:
wormus said:
I'm looking for a web site that will enable me to search by wheel width, diameter, and offset. Does such a thing exist?
www.google.co.uk
wormus said:
MyM8V8 said:
Everyones panicking about getting wider tyres. My new rears are 235's (x 60 x 15"
.
(They are just a tad bigger on the circumference.) How big do you think my contact patch will be???
but everyone tells me wider Tyres mean more grip?
. (They are just a tad bigger on the circumference.) How big do you think my contact patch will be???
are u talking about daily driving or up the strip or around a track
Monaro and VXR8 wheels
www.rimstyle.com/products/packages/car-model.html
These guys do wheel and tyre packages
www.rimstyle.com/products/packages/car-model.html
These guys do wheel and tyre packages
wormus said:
MyM8V8 said:
Everyones panicking about getting wider tyres. My new rears are 235's (x 60 x 15"
.
(They are just a tad bigger on the circumference.) How big do you think my contact patch will be???
but everyone tells me wider Tyres mean more grip?
. (They are just a tad bigger on the circumference.) How big do you think my contact patch will be???
As a generalisation, yes. Probably more accurate to say a larger contact patch will give more traction.
A taller sidewall at lower pressure will give better grip than a similar width low profile tyre.
Rubber compound helps too.
(Tbo mate you'll never get enough grip for the torque you have)
badboyburt said:
Monaro and VXR8 wheels
www.rimstyle.com/products/packages/car-model.html
These guys do wheel and tyre packages
www.rimstyle.com/products/packages/car-model.html
These guys do wheel and tyre packages
Interesting site! They have quite a lot of choice for the Monaro and like most suppliers offer the standard 8J rims which, for a 35 profile, has an ideal tyre size of 225 but can be pushed to 235 or even 245 but are no good for anything above. As the original tyres are 235 and my car is now pushing 500BHP and about the same in Lbs/Ft I wanted to go bigger on the rear.
Then I spotted that some of their offerings were 8.5J, such as: www.rimstyle.com/products/detail/?category=wheel_tyre_packages;type=aez_lascar_mg;model=248;id=AELASMG1985855120353512510 This would allow the fitment of a 255 tyre but they are an et35 offset which means the wheel will sit 13mm further out than the original et48 wheels. As far as the outer wing is concerned, this is the equivalent of a 9j rim at et48 offset and I can't see this working for the supplied 245 tyre would scrub on the outer front wing edge under full load.
To explain: I briefly tried a 9J et48 front wheel from a staggered fitment BMW, shod with 235/35 rubber. To clear the Monaro front strut I needed 3mm spacers but it looked like the 235 tyre would foul the outer wing although I can't be sure without trying it in the real world. Of course for the rear I should stand more chance fitting 9J et48 rims but I did not get the chance of trying the wheel on the rear to see.
9J rims can have anything from 245/30 to 275/30 tyres fitted so if I can make them fit then I could put 245 on the front and 275 on the rear. To allow me to experiment properly, I have bought a second hand BMW front that comes with a 255 section tyre. I have a 235/35 on a buckled TT wheel in my workshop so I can use that in my experiments. Once I have the BMW wheel, I can remove the springs from the suspension and try full deflection tests using my trolley jack to check clearance on the rear and then front on lock to lock. As I have a new set of King Springs (thanks Ian) to fit, I will take a couple of days off and do it all at once.
In theory I am looking at fitting 3mm spacers on the front (until I can afford coilovers) with 235 or 245 tyres and direct fitment with 275/30 on the rear. I will need to get some custom spigot rings for BMW to Monaro but if it works the cost for 4x second hand BMW wheels will be around £150 - £200. And the BMW 5 spoke (Y-spoke) rims look very good indeed, especially if I get them refurbed in lacquered dark chrome/silver paint!
Edited by boggie on Monday 31st May 20:43
Dont believe what companies quote for manaro offsets.
I had loads of problems with rimstock, they quoted that a 18"x8" +35 would fit. They werent to impressed when i complained that they didnt.
You can get offset topmounts for the front, s800vxr has some which allows him to use 20"x9" alloys.
I had loads of problems with rimstock, they quoted that a 18"x8" +35 would fit. They werent to impressed when i complained that they didnt.
You can get offset topmounts for the front, s800vxr has some which allows him to use 20"x9" alloys.
To be fair, it depends upon the typr of coilovers. I have seen coilovers on other cars where the coils are the same size as the McPhearson coils but I am told that the Pedders coilovers are narrower than the struts on the monaro. I will post my findings on the forum but these are the wheels I am experimenting with:

wormus said:
I'm looking for a web site that will enable me to search by wheel width, diameter, and offset. Does such a thing exist?
I dont think there is a search engine like that mate.... if you are going to be that specific then you need to start looking at things like HRE wheels, Image wheels etc. Although they are not search engines they will supply just about anything you want however you will obviously pay more than something like a TSW setup. You would be better off sorting out the rear space first then getting wheels to fit. You can have mine cheap.... 
Gassing Station | HSV & Monaro | Top of Page | What's New | My Stuff



