Best Budget Way Of Doing Heads For FI?
Best Budget Way Of Doing Heads For FI?
Author
Discussion

after_shock

Original Poster:

8,751 posts

251 months

Friday 11th June 2010
quotequote all
When I say budget im talking circa £1k for the parts not including fitting.

Ive looked many times at those Patriot set ups, anyone ever tried them? Especially as they do FI specific ones and can order them with a lower compression ratio at the same time.

Alternative option and cheapest is take the current LS2 heads off and have them CNC'd/machine polished.

Final option is probably find a set of LS3 heads that someone has taken off to be replaced and get them.

Any suggestions on the best route to take?

S800VXR

5,877 posts

231 months

Friday 11th June 2010
quotequote all
Your FI arnt you...? if so dont bother! Spend your money where its needed... talking from experiance.

Bonnie and Clyde

11,701 posts

223 months

Friday 11th June 2010
quotequote all
what forged rog

after_shock

Original Poster:

8,751 posts

251 months

Saturday 12th June 2010
quotequote all
S800VXR said:
Your FI arnt you...? if so dont bother! Spend your money where its needed... talking from experiance.


Yeah am FI, interesting perspective on it lol

Im aiming for a power target which im not sure if I can hit without altering the heads, ultimately was thinking it would help all round if the heads were a better design or better flowing.

S800VXR

5,877 posts

231 months

Saturday 12th June 2010
quotequote all
Forged, up the boost, decent intercooler and fuel upgrade. That should get you what you want. Heads are fine if you have everything else, after all with FI your shoving it in there and up to 9psi I dont think your going to have to worry to much about thermal loadings. 12psi and above and your into new territory, that or a nice TVS2300... smile

after_shock

Original Poster:

8,751 posts

251 months

Saturday 12th June 2010
quotequote all
Haha TVS2300 would be lovely although not on the cards for a good long while.

Appreciate the advice, will scrap the idea of heads then, im sure it can be better spent elsewhere.

gsd2000

11,515 posts

214 months

Saturday 12th June 2010
quotequote all
All i would say is that if you can afford a set of heads then do it when the rest of the engines in bits, if you are paying for the labour.

I get a feeling that tinker-27 may have some experience with patriot heads.

But if the choice is heads or forged bottom end, then forge the bottom end good as your FI

after_shock

Original Poster:

8,751 posts

251 months

Saturday 12th June 2010
quotequote all
Cheers for info.

Forged bottom end is definately going ahead later in the year, was just thinking whilst its in bits it would be an easy thing to do!

Going to have to look at what else is going to be needed to get done along with the forging, potentially fuelling amongst other things.

monkfish1

12,522 posts

255 months

Saturday 12th June 2010
quotequote all
With stock heads

after_shock

Original Poster:

8,751 posts

251 months

Saturday 12th June 2010
quotequote all
O.k thats fine wont bother lol

after_shock

Original Poster:

8,751 posts

251 months

Saturday 12th June 2010
quotequote all
Going slightly off topic would it be easier to change the clutch whilst the engines out?

ringram

14,702 posts

279 months

Saturday 12th June 2010
quotequote all
What you need is forging and a CAM! The gts Roger posted did just under 500rwhp at the last dyno day. Thats plenty imo. Plus there is room for a larger cam for more power. Dont forget the cam is the largest restriction in any engine! It opens the valves...

monkfish1

12,522 posts

255 months

Saturday 12th June 2010
quotequote all
after_shock said:
Going slightly off topic would it be easier to change the clutch whilst the engines out?


Very much so. Basically, no labour cost.

Edited by monkfish1 on Saturday 12th June 10:09

After_Shock

Original Poster:

8,751 posts

251 months

Saturday 12th June 2010
quotequote all
ringram said:
What you need is forging and a CAM! The gts Roger posted did just under 500rwhp at the last dyno day. Thats plenty imo. Plus there is room for a larger cam for more power. Dont forget the cam is the largest restriction in any engine! It opens the valves...
Cam is definately on the cards and will be doing it at the same time as its obviously easier to do.

Problem is now which spec of cam to go for! lol

ringram

14,702 posts

279 months

Saturday 12th June 2010
quotequote all
Loads of options mate...

Thunder Racing Custom Camshaft
" CheaTR v.3" - 219/230 .607/.604 117 LSA. Off Idle-6800 RPM Power Band. Broad power range. Works well with stock exhaust manifolds and catalytic converters. Stock like idle in 5.7L or Larger. Minor tuning required on automatic transmission cars. Responds very well to nitrous. This cam works well with "Roots style" SuperChargers.

after_shock

Original Poster:

8,751 posts

251 months

Sunday 13th June 2010
quotequote all
ringram said:
Loads of options mate...

Thunder Racing Custom Camshaft
" CheaTR v.3" - 219/230 .607/.604 117 LSA. Off Idle-6800 RPM Power Band. Broad power range. Works well with stock exhaust manifolds and catalytic converters. Stock like idle in 5.7L or Larger. Minor tuning required on automatic transmission cars. Responds very well to nitrous. This cam works well with "Roots style" SuperChargers.


Cheers for the suggestion, had a good look on the site some interesting cam specs actually!