If your dragging your car get your doughnuts checked!!!
Discussion
Just had the old girl up on the lift today for Dave to weld up a track exhaust. While up there I gave her the once over and noticed that the front doughnut is shagged, obviously due to dead hooking at the Pod last week.
I think anyone with any kind of power or manual box, dragging theirs, get underneath with a light and check everything that gets stressed, doughnuts first.
Now this has happened the next thing will have to be a prop loop.
I think anyone with any kind of power or manual box, dragging theirs, get underneath with a light and check everything that gets stressed, doughnuts first.
Now this has happened the next thing will have to be a prop loop.
MyM8V8 said:
Just had the old girl up on the lift today for Dave to weld up a track exhaust. While up there I gave her the once over and noticed that the front doughnut is shagged, obviously due to dead hooking at the Pod last week.
I think anyone with any kind of power or manual box, dragging theirs, get underneath with a light and check everything that gets stressed, doughnuts first.
Now this has happened the next thing will have to be a prop loop.
If you have a 2 piece prop.....if there is any point fitting a loop at all, there will need to be more than one.I think anyone with any kind of power or manual box, dragging theirs, get underneath with a light and check everything that gets stressed, doughnuts first.
Now this has happened the next thing will have to be a prop loop.
Although fairly sure that most donut setups even if the donut completely fails, the shaft itself still shouldnt be able to drop ?
Best option is just a setup with no rubber.
Edited by stevieturbo on Saturday 19th June 17:44
stevieturbo said:
MyM8V8 said:
Just had the old girl up on the lift today for Dave to weld up a track exhaust. While up there I gave her the once over and noticed that the front doughnut is shagged, obviously due to dead hooking at the Pod last week.
I think anyone with any kind of power or manual box, dragging theirs, get underneath with a light and check everything that gets stressed, doughnuts first.
Now this has happened the next thing will have to be a prop loop.
If you have a 2 piece prop.....if there is any point fitting a loop at all, there will need to be more than one.I think anyone with any kind of power or manual box, dragging theirs, get underneath with a light and check everything that gets stressed, doughnuts first.
Now this has happened the next thing will have to be a prop loop.
Although fairly sure that most donut setups even if the donut completely fails, the shaft itself still shouldnt be able to drop ?
Edited by MyM8V8 on Saturday 19th June 17:45
Normally prop shafts have a pilot bearing inside the doughnuts so it can't separate if the doughnuts complete fails.
In the last weeks of my dear old Granny I lost the 3 sections which are in tension going forward. So I tie wrapped up the remaining three and made a mental note not give it any welly in reverse!
In the last weeks of my dear old Granny I lost the 3 sections which are in tension going forward. So I tie wrapped up the remaining three and made a mental note not give it any welly in reverse!
Edited by granada203028 on Saturday 19th June 19:14
monkfish1 said:
The prop is located by a spigot into the gearbox tailshaft, so even if the donut is knackered, it "should" stay centred.
We fitted a BMR prop loop on harrys on the forward crossmember.
Was it welded to the chassis cross member, or did you bolt it? I think i'm doing this regardless. My knackers are worth more than $99.We fitted a BMR prop loop on harrys on the forward crossmember.
monkfish1 said:
The prop is located by a spigot into the gearbox tailshaft, so even if the donut is knackered, it "should" stay centred.
We fitted a BMR prop loop on harrys on the forward crossmember.
My new (auto) gearbox output shaft is a super strength 300M version and will have a sliding 1350 yoke. Just in case. (Can't remember seeing any kind of spigot hole in there?).We fitted a BMR prop loop on harrys on the forward crossmember.
MyM8V8 said:
monkfish1 said:
The prop is located by a spigot into the gearbox tailshaft, so even if the donut is knackered, it "should" stay centred.
We fitted a BMR prop loop on harrys on the forward crossmember.
We fitted a BMR prop loop on harrys on the forward crossmember.
Was it welded to the chassis cross member, or did you bolt it? I think i'm doing this regardless. My knackers are worth more than $99.
It was indeed

MyM8V8 said:
monkfish1 said:
The prop is located by a spigot into the gearbox tailshaft, so even if the donut is knackered, it "should" stay centred.
We fitted a BMR prop loop on harrys on the forward crossmember.
We fitted a BMR prop loop on harrys on the forward crossmember.
My new (auto) gearbox output shaft is a super strength 300M version and will have a sliding 1350 yoke. Just in case. (Can't remember seeing any kind of spigot hole in there?).
The stock output shaft will have a hole in it. The spigot is on the prop.
monkfish1 said:
MyM8V8 said:
monkfish1 said:
The prop is located by a spigot into the gearbox tailshaft, so even if the donut is knackered, it "should" stay centred.
We fitted a BMR prop loop on harrys on the forward crossmember.
My new (auto) gearbox output shaft is a super strength 300M version and will have a sliding 1350 yoke. Just in case. (Can't remember seeing any kind of spigot hole in there?).We fitted a BMR prop loop on harrys on the forward crossmember.
Gassing Station | HSV & Monaro | Top of Page | What's New | My Stuff



