Wheel's, not many?
Author
Discussion

satsuma71

Original Poster:

177 posts

197 months

Wednesday 23rd June 2010
quotequote all
Don't seem o be many wheel styles available for the ro, or at least i can't find manylaugh

Bonnie and Clyde

11,701 posts

223 months

Wednesday 23rd June 2010
quotequote all
GSD where are you

gsd2000

11,515 posts

214 months

Wednesday 23rd June 2010
quotequote all
wavey mel, here i am smile

gsd2000

11,515 posts

214 months

Thursday 24th June 2010
quotequote all
Copied from the FAQ section

Monaro Wheels

Diameter: 18" (CV8) or 19" (VXR)
Width: 8" (J)
PCD: 5 x 120mm
Offset: 48 mm
Bore: 69mm (note: check your car as there are some variances) I think i measured mine at 69.5mm


Generally speaking if you stick to an 8" rim anything between 40-48mm offset will fit, you may need to trim the rear arch lips on a 40mm offset if you have standard rear bushes, though as the rear end does move about abit on standard bushes.

The rear arch lips overhang the spot welds by around 3-4mm or so possibly more, are this overhang is past the spot welds you can safely trim this off without altering the structural integrity of the rear arches.

I personally run 18" x 8j +47mm at the front and 18" x 8.5j +50mm at the back. These look to fit perfectly, i still haven't yanked the rear spring out to check them to the bump stops (i know ive been saying this for a while now), but they look like they will fit with a bit of room to spare either side.

An 8.5" rim will allow you to fit a 255 rear tyre. Some people run a 255 rear tyre on a 8" rim, which isn't ideal but it seems to work okay.

If you want more than 255 rubber on the rear, then you need to either mini tub, or roll the rear arches. Mini tubbing isn't cheap around £2k i believe, but if you roll your rear arches then you will most likely need to respray the rear quarter panels. This is because the rear arches on a ro are triple skinned and will most likely crack the paint, so this method isnt cheap either. On mini tubbed or the arches rolled you can then safely fit 9.5" rim with a 275-285 rear tyre, without any issues.

For cheap wheels, look at BMW's. Ideally the E46 3 series, 1 series, X3 and some X5 wheels if you want 19" wheels.

Oh yeah some cheap wheels are the fronts of an e46 M3, as they are 18" x 8j +47mm

The wheels i have are BMW style 71 2 piece split rims, of an E46 330ci Clubsport. They fit and clear the AP brakes okay, they also provide a few extra mm of clearance over the standard cv8 wheels and AP's.

I do have a set of 18" x 8j +45mm Team Dynamics Pro Race 1.2S wheels in the garage which will be up for sale soon. The only set ever made for a ro (so ive been told by rimstock, which is why it took the tcensoredt's so long to make them, kept on giving me excuses and wouldnt listen) they are over 7kg a corner lighter than standard cv8 wheels and provide 15mm or so more clearance for the AP's over standard cv8 wheels.

Oh yeah dont listen to allow wheel companies claiming that their wheels will fit without issues. Most of them just want to sell you some wheels and be done with it, i had rimstock on the phone most days after they messed me around. They blamed me and monkfish for their mistakes and after it went to senior management they sent me some chrome wheel nuts as compo, that dont fit. That was after they delivered my wheels 6 months late, i later found out that they had never made wheels for a ro.

Avoid Rimstock.

Hope this helps

boggie

393 posts

253 months

Thursday 24th June 2010
quotequote all
I have a 19x9ET48 X5 Front wheel that I have been experimenting with. If I can get it to fit I should be able to run 245 front and 275 rears but I have more checks to do first. Here are the results so far:

Front Inside: 3mm spacer required to clear the strut
Front Outside: Gonna be close but need the spacer to check properly

Rear Inside: Clears OK
Rear outside: Gonna be close but need to take the springs out to check properly

B

007 VXR

64,187 posts

218 months

Thursday 24th June 2010
quotequote all
vxr8 wheels on mine 285 rears lick

monkfish1

12,522 posts

255 months

Thursday 24th June 2010
quotequote all
boggie said:
I have a 19x9ET48 X5 Front wheel that I have been experimenting with. If I can get it to fit I should be able to run 245 front and 275 rears but I have more checks to do first. Here are the results so far:

Front Inside: 3mm spacer required to clear the strut
Front Outside: Gonna be close but need the spacer to check properly

Rear Inside: Clears OK
Rear outside: Gonna be close but need to take the springs out to check properly

B


There isnt room on full bump for a 275.

after_shock

8,751 posts

251 months

Thursday 24th June 2010
quotequote all
If you mini tub I take it you need wheels with a different type of offset to take advantage of the extra space made on the inner arches otherwise fitting wheels of the same offsett that are wider will still foul the outer arches?

boggie

393 posts

253 months

Thursday 24th June 2010
quotequote all
monkfish1 said:
boggie said:
I have a 19x9ET48 X5 Front wheel that I have been experimenting with. If I can get it to fit I should be able to run 245 front and 275 rears but I have more checks to do first. Here are the results so far:

Front Inside: 3mm spacer required to clear the strut
Front Outside: Gonna be close but need the spacer to check properly

Rear Inside: Clears OK
Rear outside: Gonna be close but need to take the springs out to check properly

B


There isnt room on full bump for a 275.


Thanks. Are we talking outside rear arches? How about 265?

Edited by boggie on Thursday 24th June 22:40

007 VXR

64,187 posts

218 months

Thursday 24th June 2010
quotequote all
boggie said:
monkfish1 said:
boggie said:
I have a 19x9ET48 X5 Front wheel that I have been experimenting with. If I can get it to fit I should be able to run 245 front and 275 rears but I have more checks to do first. Here are the results so far:

Front Inside: 3mm spacer required to clear the strut
Front Outside: Gonna be close but need the spacer to check properly

Rear Inside: Clears OK
Rear outside: Gonna be close but need to take the springs out to check properly

B
There isnt room on full bump for a 275.
Thanks. Are we talking outside rear arches? How about 265?

Edited by boggie on Thursday 24th June 22:40
pic of mine tubbed if it helps 9.5 wheel with 285 tyre


jayrockwell

309 posts

225 months

Friday 25th June 2010
quotequote all
gsd2000 said:
Copied from the FAQ section

Monaro Wheels

Diameter: 18" (CV8) or 19" (VXR)
Width: 8" (J)
PCD: 5 x 120mm
Offset: 48 mm
Bore: 69mm (note: check your car as there are some variances) I think i measured mine at 69.5mm


Generally speaking if you stick to an 8" rim anything between 40-48mm offset will fit, you may need to trim the rear arch lips on a 40mm offset if you have standard rear bushes, though as the rear end does move about abit on standard bushes.

The rear arch lips overhang the spot welds by around 3-4mm or so possibly more, are this overhang is past the spot welds you can safely trim this off without altering the structural integrity of the rear arches.

I personally run 18" x 8j +47mm at the front and 18" x 8.5j +50mm at the back. These look to fit perfectly, i still haven't yanked the rear spring out to check them to the bump stops (i know ive been saying this for a while now), but they look like they will fit with a bit of room to spare either side.

An 8.5" rim will allow you to fit a 255 rear tyre. Some people run a 255 rear tyre on a 8" rim, which isn't ideal but it seems to work okay.

If you want more than 255 rubber on the rear, then you need to either mini tub, or roll the rear arches. Mini tubbing isn't cheap around £2k i believe, but if you roll your rear arches then you will most likely need to respray the rear quarter panels. This is because the rear arches on a ro are triple skinned and will most likely crack the paint, so this method isnt cheap either. On mini tubbed or the arches rolled you can then safely fit 9.5" rim with a 275-285 rear tyre, without any issues.

For cheap wheels, look at BMW's. Ideally the E46 3 series, 1 series, X3 and some X5 wheels if you want 19" wheels.

Oh yeah some cheap wheels are the fronts of an e46 M3, as they are 18" x 8j +47mm

The wheels i have are BMW style 71 2 piece split rims, of an E46 330ci Clubsport. They fit and clear the AP brakes okay, they also provide a few extra mm of clearance over the standard cv8 wheels and AP's.

I do have a set of 18" x 8j +45mm Team Dynamics Pro Race 1.2S wheels in the garage which will be up for sale soon. The only set ever made for a ro (so ive been told by rimstock, which is why it took the tcensoredt's so long to make them, kept on giving me excuses and wouldnt listen) they are over 7kg a corner lighter than standard cv8 wheels and provide 15mm or so more clearance for the AP's over standard cv8 wheels.

Oh yeah dont listen to allow wheel companies claiming that their wheels will fit without issues. Most of them just want to sell you some wheels and be done with it, i had rimstock on the phone most days after they messed me around. They blamed me and monkfish for their mistakes and after it went to senior management they sent me some chrome wheel nuts as compo, that dont fit. That was after they delivered my wheels 6 months late, i later found out that they had never made wheels for a ro.

Avoid Rimstock.

Hope this helps


Let me know if/when those lightweight wheels are up for sale if you wouldn't mind. Been in the market for some for a while, trying to get something similar to Volk/Ray's wheels.

satsuma71

Original Poster:

177 posts

197 months

Friday 25th June 2010
quotequote all
Thanx guys, 007, yours looks good with the VXR8 wheel.

Edited by satsuma71 on Friday 25th June 07:13

007 VXR

64,187 posts

218 months

Friday 25th June 2010
quotequote all
satsuma71 said:
Thanx guys, 007, yours looks good with the VXR8 wheel.

Edited by satsuma71 on Friday 25th June 07:13
ta. smile lots more grip .. spin

you can get a set from walkinshaw for under £1000 sell the tyres
easy 500.00 then pay the fish 2k to tub it .. then extra 500 for new rear tyres keep old front tyres done biggrin

007 VXR

64,187 posts

218 months

Friday 25th June 2010
quotequote all
satsuma71 said:
Thanx guys, 007, yours looks good with the VXR8 wheel.

Edited by satsuma71 on Friday 25th June 07:13
some here
http://www.monkfishperformance.co.uk/2005vxrmonaro...

monkfish1

12,522 posts

255 months

Friday 25th June 2010
quotequote all
boggie said:
monkfish1 said:
boggie said:
I have a 19x9ET48 X5 Front wheel that I have been experimenting with. If I can get it to fit I should be able to run 245 front and 275 rears but I have more checks to do first. Here are the results so far:

Front Inside: 3mm spacer required to clear the strut
Front Outside: Gonna be close but need the spacer to check properly

Rear Inside: Clears OK
Rear outside: Gonna be close but need to take the springs out to check properly

B


There isnt room on full bump for a 275.


Thanks. Are we talking outside rear arches? How about 265?

Edited by boggie on Thursday 24th June 22:40


Where your clearance problem will be will be dictated by the offset, so, i cant actually answer your question.

after_shock

8,751 posts

251 months

Friday 25th June 2010
quotequote all
monkfish1 said:
boggie said:
monkfish1 said:
boggie said:
I have a 19x9ET48 X5 Front wheel that I have been experimenting with. If I can get it to fit I should be able to run 245 front and 275 rears but I have more checks to do first. Here are the results so far:

Front Inside: 3mm spacer required to clear the strut
Front Outside: Gonna be close but need the spacer to check properly

Rear Inside: Clears OK
Rear outside: Gonna be close but need to take the springs out to check properly

B


There isnt room on full bump for a 275.


Thanks. Are we talking outside rear arches? How about 265?

Edited by boggie on Thursday 24th June 22:40


Where your clearance problem will be will be dictated by the offset, so, i cant actually answer your question.


Theoretically what would be the perfect offset for the rear in order to get the widest wheels as possible on? Without tubbing or rolling just simply trimming the rear arch.

gsd2000

11,515 posts

214 months

Friday 25th June 2010
quotequote all
Personally i would say a 9" rim at around 55mm offset may work with a 265 tyre

after_shock

8,751 posts

251 months

Friday 25th June 2010
quotequote all
gsd2000 said:
Personally i would say a 9" rim at around 55mm offset may work with a 265 tyre


Are the corvette alloys not 55mm offset? Not sure on the stud pattern tho.

gsd2000

11,515 posts

214 months

Friday 25th June 2010
quotequote all
The vettes are 5x120.65 pcd, they have the same spec rear wheels as the vxr8's.

after_shock

8,751 posts

251 months

Friday 25th June 2010
quotequote all
gsd2000 said:
The vettes are 5x120.65 pcd, they have the same spec rear wheels as the vxr8's.


So they will fit on the rear?