Fao monkfish1
Author
Discussion

gsd2000

Original Poster:

11,515 posts

214 months

Sunday 27th June 2010
quotequote all
On your dodge charger project you use an electroplating kit.

Is it any good?

Also what sort of prep work is required before the part is plated?

Ive got loads of nuts and bolts on the ro that i want to do

TIA wink

monkfish1

12,522 posts

255 months

Monday 28th June 2010
quotequote all
gsd2000 said:
On your dodge charger project you use an electroplating kit.

Is it any good?

Also what sort of prep work is required before the part is plated?

Ive got loads of nuts and bolts on the ro that i want to do

TIA


Mmmm, this will be a long reply.

Yes i do have a kit and yes it is good.

However - if i had my time again, i would buy it from Caswell Europe rather than frost. It appears more expensive but it isn't in the long run, plus you get the advice of a rocket scientist on the other end of the phone..

whoever you buy from, dont bother with the supplied power supply. Just buy a decent constant current supply. I got mine from maplins for £50.

Plating is a bit like bodywork - its all in the prep. If you can see it before you plate you will see it after!

More most of the stuff on the charger, i first put in the acid bath, which is basically oxalic acid. You can get it from Bilt Hamber. The product is called de-ox C. Buy the crystalds and mix yourself. Its not nasty stuff, so no worries. It eats rust and little else.

Once free of rust, and to improve the end finish, i put them in a vibratory tumbler for 24 hours. These are designed for doing gun cartridges. I used the "greencob" material that you can get for them. Wont damage threads etc, but will give them a slight sheen.

Now they are ready to plate. You can get normal zinc, or superbright zinc which is much shinier.

In addition, and given the anal level restoration im doing, i needed a way of replicating the "black" finish found on some parts. These are black phosphate. Not very good for rust prevention, and not easy to do at home. So i zinc plate these and then put them in a zinc blackner. These have to go in a dewatering oil afterwards (unlike normal zinc plating.) These then look like phosphate but have zinc protection.

Anyway, have a look here for some pics of it (towards the end) www.moparuk.com/forums/viewtopic.php?t=24970

Normal zinc plating requires a few seconds in a suitable colour passivate to finish

gsd2000

Original Poster:

11,515 posts

214 months

Monday 28th June 2010
quotequote all
Ive already got some deox-c an using it on all the nuts and bolts on the ro.

Im still not sure that i will go for this kit yet as i cant remove every part, and am aiming for more of a tidy up.

Also it sounds very time consuming to get a good finish, so i might just derust the parts and maybe a very thin coat of paint for now.

I want to get the car on the road asap but i will look into it somemore and maybe buy a few bits later in the year. Stuff like rusty exhaust nuts and bolts are starting to annoy me.

gsd2000

Original Poster:

11,515 posts

214 months

Monday 28th June 2010
quotequote all
Oh yeah forgot to add thankyou for the info monkfish1 thumbup

monkfish1

12,522 posts

255 months

Monday 28th June 2010
quotequote all
gsd2000 said:
Ive already got some deox-c an using it on all the nuts and bolts on the ro.

Im still not sure that i will go for this kit yet as i cant remove every part, and am aiming for more of a tidy up.

Also it sounds very time consuming to get a good finish, so i might just derust the parts and maybe a very thin coat of paint for now.

I want to get the car on the road asap but i will look into it somemore and maybe buy a few bits later in the year. Stuff like rusty exhaust nuts and bolts are starting to annoy me.


TBH, paint is useless. The thing with deox-c is that it removes any plating you have.

But yes, it is time consuming. Thats why im 10.5 years in and not finished

stevieturbo

18,110 posts

278 months

Monday 28th June 2010
quotequote all
monkfish1 said:
Anyway, have a look here for some pics of it (towards the end) http://www.moparuk.com/forums/viewtopic.php?t=2497...
Outstanding work Roger !!!

I would never have the patience to do something like that. I barely have the patience to let aerosol dry before putting a second coat on !!!

gsd2000

Original Poster:

11,515 posts

214 months

Monday 28th June 2010
quotequote all
The paint will be temporary as i will buy this kit its just that i cant spend the extra time now to plate them. The bits im planning on plating are mainly suspension and exhaust bits.

But bilt hamber deox c and deox gel is good stuff

monkfish1

12,522 posts

255 months

Monday 28th June 2010
quotequote all
stevieturbo said:
monkfish1 said:


Anyway, have a look here for some pics of it (towards the end) www.moparuk.com/forums/viewtopic.php?t=24970


Outstanding work Roger !!!

I would never have the patience to do something like that. I barely have the patience to let aerosol dry before putting a second coat on !!!


Cheers Stevie.

I think they say patience is a virtue - alledgedly!

gsd2000

Original Poster:

11,515 posts

214 months

Monday 28th June 2010
quotequote all
Roger where did you buy your vibrating polisher from?

I think that is exactly what i want to polish a load of bmw split rim bolts.

monkfish1

12,522 posts

255 months

Tuesday 29th June 2010
quotequote all
gsd2000 said:
Roger where did you buy your vibrating polisher from?

I think that is exactly what i want to polish a load of bmw split rim bolts.


Errrr cant remember. Some sort of online gun supplies shop.

gsd2000

Original Poster:

11,515 posts

214 months

Tuesday 29th June 2010
quotequote all
Ok thankyou roger, i will search the tinterweb and see what i can find

ringram

14,702 posts

279 months

Tuesday 29th June 2010
quotequote all
As a shooter, these guys have a good range of stuff..

http://www.midwayuk.com/apps/ebrowse.exe/browse?ca...

Loads to choose from there as well as media and machines etc.
I have one still in NZ. You wont get any big parts in them though, they are for rifle and pistol shell cases.

gsd2000

Original Poster:

11,515 posts

214 months

Tuesday 29th June 2010
quotequote all
I was thinking nuts and bolts for the tumbler.


drew ss

2,683 posts

215 months

Tuesday 29th June 2010
quotequote all
go stainless all the way through

gsd2000

Original Poster:

11,515 posts

214 months

Tuesday 29th June 2010
quotequote all
drew ss said:
go stainless all the way through
Thats another option

monkfish1

12,522 posts

255 months

Tuesday 29th June 2010
quotequote all
gsd2000 said:
drew ss said:
go stainless all the way through


Thats another option


Sadly not for me. Wouldn't be original, incorrect bolt markings etc, etc, etc................................

gsd2000

Original Poster:

11,515 posts

214 months

Tuesday 29th June 2010
quotequote all
I might just stick stainless ones in then

ringram

14,702 posts

279 months

Tuesday 29th June 2010
quotequote all
Yeah probably cheaper and easier..