big boy sag end cans, lol.
Discussion
after a few people thought that the new cans I make didn`t fill the gap at the back of the car enough, I thought I`d play around with some bits and bobs, and came up with these big fellas, they are 4" diameter, shorter than the other cans, and just empty, nothing inside them at all.
just been out for a spin and so far I`m quite pleased with them, because the 4" pipe is empty they act like megaphones in a way, very bassy, louder pops and bangs, but not chavy like a lads vauxhall nova
the test will be the drive down to goodwood tomorrow morning, and see what the exhaust note is like at cruise speed.
not everyones cup of tea, but welcome to comments good and bad.
just been out for a spin and so far I`m quite pleased with them, because the 4" pipe is empty they act like megaphones in a way, very bassy, louder pops and bangs, but not chavy like a lads vauxhall nova
the test will be the drive down to goodwood tomorrow morning, and see what the exhaust note is like at cruise speed.not everyones cup of tea, but welcome to comments good and bad.
mr lock pick said:
Clive you are a LEGEND matey. Having characters like you around playing with bits and bobs makes TVR ownership even more special.
Would love to see them a little longer, 4/6 inches longer always helps!
Can,t wait to hear them.
C u all 2 Moro.
Wat,s up with the Vax Nova, chav lads.;)
They will fill the gap as per conversationWould love to see them a little longer, 4/6 inches longer always helps!
Can,t wait to hear them.
C u all 2 Moro.
Wat,s up with the Vax Nova, chav lads.;)
as long as they
bad.Graeme
Just 4 the record guys Graeme has just this evening finished detailing the Sag. He is also a Legend and I would happily recommend him to anyone who,s looking for a top Detailer. The man has put so much effort into the car, as if it was his own. I honestly can't recommend him enough. A top fella even though he is a SCOTSMAN!
I hope I don,t spoil all his hard work by the time the car gets to Tag.
I would post the pictures up but I am useless at it.
Sorry for jumping off subject.
I hope I don,t spoil all his hard work by the time the car gets to Tag.
I would post the pictures up but I am useless at it.
Sorry for jumping off subject.
I think if you draw a line from the bottom of the wing to the tip of the under tray and align the outside edge of the exhaust pipe with that, that'd be ideal. Oh, and perhaps the pipe itself could do with another inch diameter? Would love to hear what you've done anyone, any chance of a recording?
Only my personal opinion, after much looking at the original pic, then looking at the rear of mine. No more than an inch, I do like the way it shows more of the tyre, and as for a more bassy note and louder pops and bangs, I'm thinking it's time for a change.
Each to their own but from me, nice work.
Each to their own but
from me, nice work.right, I am goint to cut, and lengthen these today, after measuring up last night if I make them 45mm longer, the outer edge of the pipe will be in line with the outer edge of the bottom tray, if I lengthen by 70mm the pipe will poke out through the end of the bottom tray 25mm, to be honest, I like to see more of the tyre myself, but will go with a mojority vote to see what it looks like, so you`ve got until 1.30pm to voice your opinions, before the disc cutter comes out!
Who's up early this morning?
Just a quick one Clive. If you look at the picture at the very top of the post, it appear's that the can on the right is virtualy level with the outer of the bottom tray. Then in the angled shot it appears that the can is far from level.
The question I have is: When standing from the raer of your car, dead centre, do the end of the cans appear to be 45mm too short.
Just a quick one Clive. If you look at the picture at the very top of the post, it appear's that the can on the right is virtualy level with the outer of the bottom tray. Then in the angled shot it appears that the can is far from level.
The question I have is: When standing from the raer of your car, dead centre, do the end of the cans appear to be 45mm too short.
Who's up early this morning?
Just a quick one Clive. If you look at the picture at the very top of the post, it appear's that the can on the right is virtualy level with the outer of the bottom tray. Then in the angled shot it appears that the can is far from level.
The question I have is: When standing from the rear of your car, dead centre, do the end of the cans appear to be 45mm too short. It could just be me and the pictures giving me a false reading
Just a quick one Clive. If you look at the picture at the very top of the post, it appear's that the can on the right is virtualy level with the outer of the bottom tray. Then in the angled shot it appears that the can is far from level.
The question I have is: When standing from the rear of your car, dead centre, do the end of the cans appear to be 45mm too short. It could just be me and the pictures giving me a false reading
If I am allowed to join in I would vote for the same length as the originals if not longer. If they do not stick out they look a bit sad, the carbon can company ones look too short as well and if you put extensions on them you can then see them on the inside.
When the exhaust fills all the gap it looks great. I like the shape you have created clive.
When the exhaust fills all the gap it looks great. I like the shape you have created clive.
Gassing Station | Tamora, T350 & Sagaris | Top of Page | What's New | My Stuff