Code reader
Author
Discussion

Muffster

Original Poster:

312 posts

224 months

Friday 10th November 2017
quotequote all
Evening folks. After doing some reading on here i got hold of an OBD2 code reader, its a U480 type like some of the other guys have got.
I've got the familiar emission service required on the dash on my 07 V8V.
So after squeezing myself into the foot well and plugging it in.......nothing, it did not even switch on its clearly not getting a 12v signal from the OBD port.
Anyone else have this, is the cheap price of these readers too good to be true?

Thanks.

john ryan

542 posts

163 months

Friday 10th November 2017
quotequote all
Have you switched on the ignition? Have you got it in the correct port (of two)?

Muffster

Original Poster:

312 posts

224 months

Friday 10th November 2017
quotequote all
Hello John,
Yes ive got it plugged into OBD rather than body and switched the ignition on, no joy.

matrignano

4,702 posts

241 months

Friday 10th November 2017
quotequote all
Mine is a bit fiddly to plug in and needs to be pushed in forcefully (ohhh errrrrr), have you tried?

Gday2

219 posts

154 months

Friday 10th November 2017
quotequote all
Obd port should supply voltage for the reader even without ignition.
Check the fuse F51 in cabin fuse box.

bogie

17,106 posts

303 months

Friday 10th November 2017
quotequote all
My obdII reader runs on batteries....you sure it does not need some ? With key in position 1, I plug it on, switch the reader on and click "connect" then it scans and connects to the car

Muffster

Original Poster:

312 posts

224 months

Friday 10th November 2017
quotequote all
This type is definitely powered by the car battery.
I have given it a good shove and managed to pop it out of the bracket it sits in.
Next stop fuse 51.

rovcallum

553 posts

174 months

Saturday 11th November 2017
quotequote all
If its not working, shove it in the other OBD port just to rule it out. Will do no harm.

Muffster

Original Poster:

312 posts

224 months

Saturday 11th November 2017
quotequote all
Success. Must have just been some of the pins were misaligned as I tried to connect it.
Tried it on the Audi and it worked first time. Plugged it back into the V8V and it worked and cleared the codes. Job jobbed.
Next has anyone DIY'd an O2 sensor?

Thanks.

bogie

17,106 posts

303 months

Saturday 11th November 2017
quotequote all
See redpants site for lots of DIY info e.g. jacking the car up correctly http://www.redpants.lol/

O2 sensor is straightforward enough, although I just watched my local garage guys do mine, for £45 ph labour, and me just having a jack versus a lift, it was not worth getting my hands dirty.


Muffster

Original Poster:

312 posts

224 months

Sunday 12th November 2017
quotequote all
Hi Bogie, thats a fair point and sounds reasonable for having them done. I actually really enjoy getting my hands dirty which is something i have missed doing this year. I'd like to do the sensors myself and was wondering how accessible they are whilst i'm on my back on the garage floor.

Gday2

219 posts

154 months

Sunday 12th November 2017
quotequote all
Laying on the back is not the worst but does it have to be the garage floor and 1600 Kg above? smile

bogie

17,106 posts

303 months

Sunday 12th November 2017
quotequote all
You will need the car up on axle stands and then it will be awkward, but not impossible