Tyre Pressure sensors
Tyre Pressure sensors
Author
Discussion

philip600

Original Poster:

216 posts

205 months

Monday 4th December 2017
quotequote all
Hi,

I'm thinking of getting the wheels powder coated on my 2006 V8V. It's fitted with the tyre pressure monitor system, can the sensors fitted to the wheels be easily removed & re-fitted after powder coating or is it preferable to replace them ? Alternately could I just get rid of them or would this bring up a warning ?

Cheers, Phil.

Graze01

1,203 posts

123 months

Monday 4th December 2017
quotequote all
Phil

On the early cars you can just delete them and disconnect the wiring under the dash below the glove box. No warning message comes up

Graze

leerandle

834 posts

138 months

Monday 4th December 2017
quotequote all
Very easy to remove and replace whilst refurbing alloy wheels. Mine were done a few years ago and standard practise these days. If they’re still working, then don’t bother replacing with new ones. It can get expensive buying and coding new ones.

tonycordon

296 posts

261 months

Tuesday 5th December 2017
quotequote all
My experience, when having my 2007MY V8V's wheels refurbished earlier this year was that whilst the actual sensors were easy to remove (one screw, I think) the valves themselves were impossible to undo without breaking them. I tried, at the time, to source new, compatible valves but could only find the genuine AM ones at an eye watering price because they won't sell the valves without the sensors! In fact when I queried this the advice was, 'you will have to buy the valves and sensors, but we advise you to use your old sensors, because, otherwise the new ones will need to be programmed to match the car!'
I went down the removal route and disconnected the control box in the passenger footwell.
I believe that valves can be obtained via McGurks (and probably others) but I didn't have time to investigate this properly.
My advice would be, either to fit ordinary valves and disconnect, or to be better prepared than me and source the valves first.

steveway

947 posts

115 months

Tuesday 5th December 2017
quotequote all
I have just replaced my wheels on my 2010 V12V without sensors and used a delete wire from Redpants which means no warning lights on the dash but I now have to check my own tyre pressures-big deal.

leerandle

834 posts

138 months

Tuesday 5th December 2017
quotequote all
Is this not the valve that you need ?

http://astonmartinbits.com/models/5-V8-Vantage/par...

I know a lot of people have disconnected the TMPS with the Redpants kit, but I (at the time) got alloys refurbed, new sensors tyres etc.

tonycordon

296 posts

261 months

Tuesday 5th December 2017
quotequote all
Yes Lee, they are the ones! If only i'd seen them at the time. Maybe Should buy a set and get them fitted, or maybe I'ii just carry on using my pressure gauge!

4x4sche

30 posts

123 months

Tuesday 5th December 2017
quotequote all
Here is the lowdown on the TPMS that was fitted to early cars. The system was supplied by Bendix and called "Smarttire". If you get a warning it will indicate either a failure of the system or a tire problem. There is a box in the footwell with led's that indicate the problem wheel. There is connection from this box to the cars wiring. On the first implementation the instrument warning will not occur if you disconnect the box, on later models you need to alter the wiring after you unplug it to get the warning to staty off. (Redpants sells a cable that does this) There are no compatible aftermarket sensors for the Smarttire system.

If you change the sensor on any of the wheels, or have a second set of wheels (as I do for Winter driving) then the ID of each new sensor needs to be programmed into the Smarttire box using a special tool. This programming tool is no longer available, but the authorized dealers have them. There are at least two versions of the programmer needed to cover all models. I have two of the Smarttire boxes and each one is programmed with the ID's of one set of wheels. When I change my wheels over, I also change the Smarttire box to match up. This avoids constant reprogramming of the ID's.

Disconnecting the box is a possibility, but in a car with no spare wheel, I like to know if my tires are leaking so I can avoid being stranded. Checking the pressure with a gauge cannot be done while driving, so you will be made aware of a problem when your tire goes flat enough to affect the handling. With TPMS you stand a chance of the earlier detection of a problem giving you the chance to drive to a safe spot.

Ken Figenus

6,011 posts

148 months

Tuesday 5th December 2017
quotequote all
leerandle said:
If they’re still working, then don’t bother replacing with new ones. It can get expensive buying and coding new ones.
I think batteries last about 6 years so I’d seriously consider replacing them whilst the wheel are all off if it’s over 4 yrs old.

I only found totally conflicting info on if they self program (how can they know which wheel they are on???) or need manual coding. The parts are made by Beru who have been bought out by Huf I think.

leerandle

834 posts

138 months

Tuesday 5th December 2017
quotequote all
Ken Figenus said:
I think batteries last about 6 years so I’d seriously consider replacing them whilst the wheel are all off if it’s over 4 yrs old.

I only found totally conflicting info on if they self program (how can they know which wheel they are on???) or need manual coding. The parts are made by Beru who have been bought out by Huf I think.
I don't think you can get replacement batteries, they are closed unit (Mine were anyway).

However, I was told you can now buy aftermarket sensors that can be programmed by others, not just AM dealers (I didnt take this any further, but could be a far cheaper option and you still get tyre warnings if losing pressure/puncture etc)

Ken Figenus

6,011 posts

148 months

Tuesday 5th December 2017
quotequote all
leerandle said:
I don't think you can get replacement batteries, they are closed unit (Mine were anyway).

However, I was told you can now buy aftermarket sensors that can be programmed by others, not just AM dealers (I didnt take this any further, but could be a far cheaper option and you still get tyre warnings if losing pressure/puncture etc)
Yes its a sealed unit mate - whole lot has to be changed - just had two. Job pushed £200 per wheel when done piecemeal! £72 per vat per actual sensor from AM.

philip600

Original Poster:

216 posts

205 months

Tuesday 5th December 2017
quotequote all
Thanks for the advice & heads up. I'll see how they go but may just replace them with standard valves if they're going to be an issue.
Cheers, Phil.