Loud bang from rear suspension - DB9
Loud bang from rear suspension - DB9
Author
Discussion

V12JDC

Original Poster:

190 posts

121 months

Monday 5th March 2018
quotequote all
Hi all,

A little help please

I head a slight clunk the last time I took my 2005 DB9 Manual out when either braking or accelerating, tonight I took my car out to bed in new front discs and pads and was obviously transitioning from moderate braking to moderate acceleration and at a certain effort, I get a loud bang under the drivers side rear of the car, similar as someone else has described to a lump hammer being hit under the car.

A quick look under in the wet and dark didn't reveal anything but a quick searching here appears to suggest a split resr lower arm casing allowing the arm to slide on its bushings, this does feel like just the fault.

Has anyone had this problem and where and how did they fix it?

Thanks

John

rovcallum

553 posts

174 months

Monday 5th March 2018
quotequote all
Could it be a coil spring reseating after being fully extended/unseated whilst getting work done?
Is the ride height the same on both sides?

V12JDC

Original Poster:

190 posts

121 months

Monday 5th March 2018
quotequote all
Good shout but that isbone thing I checked and it's bang on

It seems cracked wishbone are reasonably common so will check closely for that Wednesday night

John

V12JDC

Original Poster:

190 posts

121 months

Wednesday 7th March 2018
quotequote all
So after an inspection and subsequent strip, it's clear to see whats happened.

Is seems very rare and it seems to have split on the thinnest part of the casting




bentleyspeed

477 posts

170 months

Wednesday 7th March 2018
quotequote all
Can the bush be pressed out, the arm welded and the bush replaced rather than a new arm assembly?
I bet it's not cheap.................

V12JDC

Original Poster:

190 posts

121 months

Wednesday 7th March 2018
quotequote all
370 from a dealer, 350 with some discount, 230 on eBay for a new one and 150 for a used one.

I am not sure welding it would be a good repair or ensure the Bush was right after repair

bentleyspeed

477 posts

170 months

Wednesday 7th March 2018
quotequote all
At that price, I'd be trying a repair. I'm sure a good local machine shop could beef up that eye and it be stronger than new. It's cracked at the thinnest point.

Graze01

1,203 posts

123 months

Wednesday 7th March 2018
quotequote all
I find it interesting that the crack is in the bush housing - apparently at a point where I would expect there to be little load (being the back side)

I would think a repair should be fine if you can find the right company to do it

Graeme

R129 300SL

281 posts

163 months

Thursday 8th March 2018
quotequote all
These look like cast aluminium. Not sure welding them is the best course of action. Aluminium welds are weaker than the actual aluminium I think.

rovcallum

553 posts

174 months

Thursday 8th March 2018
quotequote all
£307 from astonmartinbits, brand new.

Also, if there is an upside here it's that after you replace the arm you'll have to get the geometry checked and reset, which is always handy.

V12JDC

Original Poster:

190 posts

121 months

Thursday 8th March 2018
quotequote all
Yes I had already planned to get a wheel alignment, it's well overdue.

Whilst TIG welding cast ally is possible, I am concerned about getting the hole in the arm to the exact same size as it should be so that the Bush doesn't keep slipping back and forth.

I think a new arm is the only sure way

8Tech

2,221 posts

229 months

Thursday 8th March 2018
quotequote all
This was similar to a thread we had a while back about replacing the spherical joints/bushes.

It is not a good idea to replace these in aluminium arms because of the likelyhood of actually causing these fractures and I suspect that this is why (in my experience) Astom Martin and BMW only offer exchange arms when made from cast aluminium.

Clearly, they had to be pressed in originally, but rather than using tons of hydraulic pressure to install, I suspect the arms are heated and the bushes/joints are frozen to allow installation.

There is absolutely no chance I would consider welding a cast aluminium arm and then trying to press in a replacement joint.