Vantage carbon dash switch over, help!
Vantage carbon dash switch over, help!
Author
Discussion

UncleStig

Original Poster:

117 posts

159 months

Monday 26th March 2018
quotequote all
Bought the carbon centre dash section to replace the plastic one on my 2009 manual Vantage. I’ve taken it all apart only to find the start switch hole is too big. When I insert my start switch there’s a 1mm gap at the top. I’ve aligned it all correctly but it simply looks like the hole in the new carbon unit is too big. Or I’m missing some kind of washer fixture.
Has anyone done this swap? Or have an idea of what’s going on.
Thanks one and all.

UncleStig

Original Poster:

117 posts

159 months

Monday 26th March 2018
quotequote all
Some more info. The diameter of the start button hole in my existing dash is 40mm. The diameter of the hole in the new carbon dash is 44mm.
I thought maybe the plastic trim around the start button should push through the hole rather than sit on top but it’s diameter is 45mm so it can’t push through.
Something is amiss.

UncleStig

Original Poster:

117 posts

159 months

Tuesday 27th March 2018
quotequote all
Another thought, could this carbon waterfall be for the older start button without the glass key? Is that start button 4mm wider in diameter? If someone with that type of start button could measure it, it would be appreciated.
Thanks

Bobajobbob

1,599 posts

127 months

Tuesday 27th March 2018
quotequote all
Either way the finishing around the edge of the carbon looks a bit rough. Is that an official Aston part?

UncleStig

Original Poster:

117 posts

159 months

Tuesday 27th March 2018
quotequote all
Yes it’s an official Aston part. As you say, the edge isn’t smoothed off so you would think the start button would sit over the hole to hide the finish.

leerandle

834 posts

138 months

Tuesday 27th March 2018
quotequote all
Bobajobbob said:
Either way the finishing around the edge of the carbon looks a bit rough. Is that an official Aston part?
I do believe the hole size did change between the push start button versus the glass key (I had a similar problem when i purchased a new piano black door).

As regards the finish, I think the pictures shown still show the plastic film covering.

NeinFondue

860 posts

187 months

Tuesday 27th March 2018
quotequote all
The push button hole is smaller than that of the ECU.

Edit: If this is an official part purchased from Aston Martin, I’d ask for an exchange.

UncleStig

Original Poster:

117 posts

159 months

Tuesday 27th March 2018
quotequote all
Yes, it’s still got the plastic protective film over it
But you can see the finish around the hole is to be covered by the button surround.

UncleStig

Original Poster:

117 posts

159 months

Tuesday 27th March 2018
quotequote all
If the push button is smaller than the glass key, why the hell is the carbon hole so damn big. Maybe the wrong drill bit was used at Aston HQ

leerandle

834 posts

138 months

Tuesday 27th March 2018
quotequote all
UncleStig said:
If the push button is smaller than the glass key, why the hell is the carbon hole so damn big. Maybe the wrong drill bit was used at Aston HQ
If I get chance tonight, I will measure mine and we can compare hole sizes............

silverspeed

1,508 posts

261 months

Tuesday 27th March 2018
quotequote all
Assuming it was purchased through a main dealer they should have ordered against your VIN number to avoid any such issues . I would have a chat with them .

ilikeAstons

275 posts

135 months

Tuesday 27th March 2018
quotequote all
Hey UncleStig. I have a 2008 DB9 with the normal Ford keyed the full start button. I measured it this afternoon - the diameter from a 9 o'clock position straight through the centre to the 2 o'clock position. It is exactly 35mm.

I hope this helps.... James

UncleStig

Original Poster:

117 posts

159 months

Tuesday 27th March 2018
quotequote all
I ordered it through Astonmartinbits who ordered it direct from Aston for me, they’ve been very helpful today.
You’re all right, the push button is smaller than the glass button. The hole shouldn’t be as big as it is I’ve been told. Astonbits have been in touch with Aston and I think there’s some head scratching going on as my start switch should be a snug fit they’ve been told, not like what I’ve got at the moment. My VIN no has been passed on so we should get there in the end. It may be as simple as the wrong hole size being drilled.... it happens.
I’ll keep you all posted. Thanks for everyone’s help. Appreciated.

tonyhall38

4,194 posts

247 months

Tuesday 27th March 2018
quotequote all
Probably more of a case of the wrong unit supplied by astonmartinbits.....I thought most of their stuff was second hand or donated by scrap donor vehicles....I may be wrong and if I am I apologise....

UncleStig

Original Poster:

117 posts

159 months

Tuesday 27th March 2018
quotequote all
This is a very new item, what none of us can explain is what would actually fit in the hole size cut. Time will tell.
I have to say, Astonbits have always been brilliant, on this occasion it’s through no fault of their own, they’re the middle man.
I couldn’t go direct to my local Aston garage as I’d pay import duty on the item. Plus their local markup. And i like their friendly email communication.
Let’s see what happens tomorrow smile

DB9VolanteDriver

2,661 posts

207 months

Tuesday 27th March 2018
quotequote all
ilikeAstons said:
Hey UncleStig. I have a 2008 DB9 with the normal Ford keyed the full start button. I measured it this afternoon - the diameter from a 9 o'clock position straight through the centre to the 2 o'clock position. It is exactly 35mm.

I hope this helps.... James
9 --- > 2 ??

You must have some strange clock face if that's how you measured the diameter...laugh

UncleStig

Original Poster:

117 posts

159 months

Tuesday 17th April 2018
quotequote all
Hello again. It doesn't appear I'm any closer to solving my carbon hole issue.
So I've sent it back to astonmartinbits who have compared it to another new dash and the holes are the same size. In other words, their new waterfall dash holes are bigger than the hole I have in my existing dash.
They've contacted Aston for advice but not received a reply yet.
The carbon dash I got from them, they got direct from Aston, so it's not some hooky copy.
One question was raised, maybe the start bezel now sits "in" the hole rather than "on" the hole.
I don't think this is the case though as my start bezel housing the glass key is 1mm in diameter larger than the diameter of the carbon hole. As both objects are solid and non flexible, there's no way it's going to fit in the hole. It must surely sit over it.
Has anyone got or upgraded to a carbon waterfall recently? Or a new centre piece in any material for that matter, if so does your bezel housing the glass key sit inside the hole or on top? Any help resolving this is appreciated

dbs2000

2,756 posts

223 months

Wednesday 18th April 2018
quotequote all
It might seem a daft question but can you change out the bezel for a larger one?

UncleStig

Original Poster:

117 posts

159 months

Wednesday 18th April 2018
quotequote all
It’s not a daft question, I thought there was only one size, if anyone can confirm the size of their ECU bezel than that would be helpful.

telum01

987 posts

146 months

Friday 20th April 2018
quotequote all
That doesn't look OEM at all. You sure it's made properly?