Tyre valve cover grub screw size
Tyre valve cover grub screw size
Author
Discussion

AMvantageBJB

Original Poster:

10 posts

102 months

Sunday 27th May 2018
quotequote all
Hi; new here
Can anyone tell me what size allen key I need to undo the grub screws on the AM Vantage tyre valve covers?
It must be mighty small 0.5mm???
Thanks

rovcallum

553 posts

174 months

Sunday 27th May 2018
quotequote all
Must admit to not having seen or heard of this before.
Can you put a pic up?

Incognegro

1,560 posts

164 months

Sunday 27th May 2018
quotequote all
I take it they are anti theft locking ones. Not sure the size u need but they are a nightmare after winter as they rust, thread and seize (happened on my Range Rover ones) the best solution I found was to just tighten with a 10mm spanner

telum01

987 posts

146 months

Sunday 27th May 2018
quotequote all
I haven't heard of this, either...
There's a tiny hold in the side but that's not for a screw - it's just there so you can insert something to keep the valve stem from spinning while you're using a T20 Torx bit for the screw at the bottom of the valve stem.

AMvantageBJB

Original Poster:

10 posts

102 months

Sunday 27th May 2018
quotequote all
Thanks; pic attached [grub screw is on LHS of valve cover]

Also just found out a 0.5mm allen key is available [my previous smallest here is 1mm]


telum01

987 posts

146 months

Monday 28th May 2018
quotequote all
Ah, that's a new one for me. What car is that on? Looks like an older style.

8Tech

2,221 posts

229 months

Monday 28th May 2018
quotequote all
That is a very common accessory part avaiable from both Aston Martin and the aftermarket.
They are theft resistant logo valve caps and are usually aluminium with a 0.5 or 0.75mms grub screw to lock them.
Your Allen key could well be in your tool kit.
I advise lightly lubricating the thread when refitting to eliminate any corrosion between the cap and the valve stem.
They can be undone with an 11mm spanner usually when tight but undo the grub screw first because it locks against the brass thread of the valve.
It is to lock the cap in place so it cannot get stolen by finger grip only.

Edited by 8Tech on Monday 28th May 13:26

AMvantageBJB

Original Poster:

10 posts

102 months

Monday 28th May 2018
quotequote all
Thanks again
Nearly there; thanks for the maintenance advice
Looks like I need a 0.5/0.75 mm key [smallest in my set is 1.0mm]
ps fyi car is 06 vantage; no idea of the origin of these caps

AMvantageBJB

Original Poster:

10 posts

102 months

Monday 28th May 2018
quotequote all
ordered the 0.7 but cannot find a 0.5 online. Not sure it's available so hoping 0.7 fits

8Tech

2,221 posts

229 months

Wednesday 30th May 2018
quotequote all
They look pretty corroded and you might be able to loosen off that grub screw with some thin pliers as it SHOULD only be nipped up.
You can always refit them without locking them on again because the sight of the grub screw is normally deterrent enough.

If I were you though, I would get myself a nice newest and use the key they will come with to remove the old ones. Clean them up and you have some spares.

Edited by 8Tech on Wednesday 30th May 17:53

Beechburn

76 posts

108 months

Wednesday 30th May 2018
quotequote all
Take extreme care in trying to remove the dust cap once you have the grub screw removed. I say this as I experienced something similar when an aftermarket cap had corroded itself onto the value. When trying to loosen the cap, even after copious amounts of WD40 and very little pressure applied, the valve stem broke. This results in immediate loss of total tyre pressure and either needing a tow truck or a spare wheel. And of course a nice invoice for a new TPMS valve. Good luck

goddo

439 posts

163 months

Thursday 31st May 2018
quotequote all
Allen key at 0.5mm is available on Amazon.
Almost £20 each!!