E39 - Traction Control light on but no associated OBD Code
E39 - Traction Control light on but no associated OBD Code
Author
Discussion

Origin Unknown

Original Poster:

2,498 posts

200 months

Wednesday 27th June 2012
quotequote all
Had the car cleaned at the weekend and the day after, the traction control light (DSC) is now permanently illuminated. The ABS light is NOT illuminated. When the car was cleaned at the weekend, the wheels were black and it did involve a power washer so I'm wondering if this has upset one of the wheel sensors.

Anyway, ran a scan tool (EasyOBDII) against the car today and the only fault code logged was P1620 which seems to be an error with the electronic thermostat (can anyone confirm?). Firstly, I cleared it but it returned straight away so there is certainly something wrong there but I'll have address that separately.

So, where do I begin if there are no error codes being thrown? I’m assuming that P1620 is NOT associated with the DSC system but can someone confirm?

This diagram shows the inputs to the DSC system but any advice where I start?

http://www.bimmerfest.com/forums/attachment.php?at...

2001 530iA

Quinten

1,172 posts

272 months

Wednesday 27th June 2012
quotequote all
I'm sure that you'd see error codes logged when you've got a warning light permanently on. Are you sure your OBD2 tool is the right one for the job?

I've had DSC and ABS lit up in the past, which turned out to be a faulty ABS module. Error codes were present, although they pointed towards all the other sensors, not the actual ABS module...

GBB

1,737 posts

190 months

Wednesday 27th June 2012
quotequote all
I've had my codes read coming up as faulty sensor and faulty block.

However the light is intermittent, comes on and stays on for a week or so, then goes off for a week or so.

I'm guessing this points to sensor (especially as it once went over when I booted the car on gravel) but could it still be the block?

Fox-

13,578 posts

277 months

Wednesday 27th June 2012
quotequote all
I'm not sure if the generic scan tools can do anything more than interrogate the ECU and the fault codes for the DSC will be stored elsewhere. You need to get some proper BMW specific diag kit hooked up.

blank

3,767 posts

219 months

Wednesday 27th June 2012
quotequote all
As above. Most generic obd tools will only speak to the engine ECU.

You need a BMW diagnostic tool or a good third party one that will speak to other control units.

GBB

1,737 posts

190 months

Wednesday 27th June 2012
quotequote all
blank said:
As above. Most generic obd tools will only speak to the engine ECU.

You need a BMW diagnostic tool or a good third party one that will speak to other control units.
My results were from the BMW kit, any ideas?

Origin Unknown

Original Poster:

2,498 posts

200 months

Wednesday 27th June 2012
quotequote all
Quinten, Fox, Blank, thanks. That makes sense. I think at a minimum I need to inspect the sheel sensors at the weekend to see if there is anything obvious.

Secondly, the error code thats being thrown implies that the thermostat is stuck open. Anyone agree with this?

ETA: sheel = wheel

Edited by Origin Unknown on Wednesday 27th June 20:42

Quinten

1,172 posts

272 months

Wednesday 27th June 2012
quotequote all
3rd result on Google: http://www.bmwland.co.uk/forums/viewtopic.php?f=4&... Nothing to worry about it says

I noticed you're in Berks? I'm in Aylesbury, Bucks and have INPA/GT1/DIS/PA Soft BMW Scanner and am not afraid to use them... wink

miniman

30,232 posts

293 months

Wednesday 27th June 2012
quotequote all
Origin Unknown said:
Quinten, Fox, Blank, thanks. That makes sense. I think at a minimum I need to inspect the sheel sensors at the weekend to see if there is anything obvious.

Secondly, the error code thats being thrown implies that the thermostat is stuck open. Anyone agree with this?
Wouldn't be surprised at the stat, common issue.

blank

3,767 posts

219 months

Wednesday 27th June 2012
quotequote all
As above. Most generic obd tools will only speak to the engine ECU.

You need a BMW diagnostic tool or a good third party one that will speak to other control units.

GBB

1,737 posts

190 months

Thursday 28th June 2012
quotequote all
What's a good scanner and are there any Windows 7 ones around at reasonable cost?

After this months PPC car article I'm toying with buying a generic one for circa £80 but not sure if that's the best option.

Quinten

1,172 posts

272 months

Thursday 28th June 2012
quotequote all
GBB said:
What's a good scanner and are there any Windows 7 ones around at reasonable cost?

After this months PPC car article I'm toying with buying a generic one for circa £80 but not sure if that's the best option.
I bought mine from http://bmtechnic.co.uk/

His support is fantastic (even on his holidays he was helping out), the one-click launch and install application makes the software install a breeze (just google for INPA setup and look at the many, many requests for help on it). And he also provides great support here http://forums.m3cutters.co.uk/forumdisplay.php?f=7...

My PA Soft cable came from Dealextreme which works with the latest PA Soft full software

GBB

1,737 posts

190 months

Thursday 28th June 2012
quotequote all
Quinten said:
I bought mine from http://bmtechnic.co.uk/

His support is fantastic (even on his holidays he was helping out), the one-click launch and install application makes the software install a breeze (just google for INPA setup and look at the many, many requests for help on it). And he also provides great support here http://forums.m3cutters.co.uk/forumdisplay.php?f=7...

My PA Soft cable came from Dealextreme which works with the latest PA Soft full software
Cheers, my Dad has just bought something similar but had problems running it on his laptop. Are you running it on a 64bit machine?

Quinten

1,172 posts

272 months

Thursday 28th June 2012
quotequote all
GBB said:
Cheers, my Dad has just bought something similar but had problems running it on his laptop. Are you running it on a 64bit machine?
No, I'm running it on Macbook Pro (Mid-2009) in Bootcamp, on Windows XP SP3 32bit. There is one part of the software which will not run on 64bit. But afaik the software should run on Windows 7 as well.

GBB

1,737 posts

190 months

Friday 29th June 2012
quotequote all
A quick post to than Quinten for being an excellent PH'er who gave me an hours teach in on Scanners and Software last night (and fitted one of the lights bought!)

Worth investing in the right kit!