E39 540 engine problem
Discussion
brief sumary
The cars a 97, 540i with 83k on it
started getting low coolant warning lamps
2 top ups then off to the garage it goes. Cut a long story short, rad was replaced as this eventually snapped at the top hose connection. This was put down to wrecked engine mounts as a month later, tha fan actually cut through the top hose. Runs fine for a week then bang, drops all its colant again, only this time from a rear hose.
At no point had the warnign lights came on for the temp sensors, but im fully aware that there could hav been hot spots due to there being no coolant flow
So, water pump was replaced, then there was no coolant flow once all ack together again and it started to blow up the top hose like a balloon with in minutes.
My engine is now inbits, heads both off and there is no sgn of any gasket damage, but appears both heads are warped.
Question is tis, has anyone came across problems similar to this before on the 540 or the 535?
i will dy-pen the heads tomorrow to see if any cracks are evident but this has got me slightly puzzeled as to why, or even both heads appear to be warped.
My plan is at the minute, to do tha above, machine both heads, replace gaskets and rebuild. dows this sound sensible or have i possibly got a bigger problem looming that i have not noticed.
Thanks in advance for any light that can be shed on this
jon
The cars a 97, 540i with 83k on it
started getting low coolant warning lamps
2 top ups then off to the garage it goes. Cut a long story short, rad was replaced as this eventually snapped at the top hose connection. This was put down to wrecked engine mounts as a month later, tha fan actually cut through the top hose. Runs fine for a week then bang, drops all its colant again, only this time from a rear hose.
At no point had the warnign lights came on for the temp sensors, but im fully aware that there could hav been hot spots due to there being no coolant flow
So, water pump was replaced, then there was no coolant flow once all ack together again and it started to blow up the top hose like a balloon with in minutes.
My engine is now inbits, heads both off and there is no sgn of any gasket damage, but appears both heads are warped.
Question is tis, has anyone came across problems similar to this before on the 540 or the 535?
i will dy-pen the heads tomorrow to see if any cracks are evident but this has got me slightly puzzeled as to why, or even both heads appear to be warped.
My plan is at the minute, to do tha above, machine both heads, replace gaskets and rebuild. dows this sound sensible or have i possibly got a bigger problem looming that i have not noticed.
Thanks in advance for any light that can be shed on this
jon
My 96 540 was a dog. Replace the entire cooling system; radiator, expansion tank, hoses, pump, Valley pan gasket.
I still had misfires galore but if your only problem is coolant then the above should sort it.
I've seldom heard head gasket failure unless it's an organic gasket Alpina B10.
Ballooning of hoses sounds like you need to spend another hour or two bleeding the bugger though.
I'd never recommend an old BMW V8 to anyone but perhaps I was unlucky.
Best of luck chap
I still had misfires galore but if your only problem is coolant then the above should sort it.
I've seldom heard head gasket failure unless it's an organic gasket Alpina B10.
Ballooning of hoses sounds like you need to spend another hour or two bleeding the bugger though.
I'd never recommend an old BMW V8 to anyone but perhaps I was unlucky.
Best of luck chap

Edited by Crombers on Thursday 5th July 00:38
thanks for that
got the engine apart and got a good look at the various parts. Both heads are warped, checked on a cmm, one head is out of flatness by .007" and the other by .008", or for anyone not conversant with the imperial system, .2mm
quite a gap all in all. unearthed a few problems such as the offside bank appears to have been running rather rich. The main thing is, from what i can see, the gaskets appear to be in good condition as do the heads and faces of the block. Im guessing through the 3 times the car has droped its coolant, its taken its toll and both heads have warped. dy-pen has so far showed up nothing, but a check in the morning will satisfy my worry about cracks in the heads.
as you can see in the pics, the offside head and nearside are in 2 very different conditions. Its going to be a case of new gaskets, rebuild and hope it all works once ive machined them flat again tomorrow. #here goes#



link to some of the pics taken so far
http://smg.photobucket.com/albums/v640/RA11YE/Rebu...
got the engine apart and got a good look at the various parts. Both heads are warped, checked on a cmm, one head is out of flatness by .007" and the other by .008", or for anyone not conversant with the imperial system, .2mm
quite a gap all in all. unearthed a few problems such as the offside bank appears to have been running rather rich. The main thing is, from what i can see, the gaskets appear to be in good condition as do the heads and faces of the block. Im guessing through the 3 times the car has droped its coolant, its taken its toll and both heads have warped. dy-pen has so far showed up nothing, but a check in the morning will satisfy my worry about cracks in the heads.
as you can see in the pics, the offside head and nearside are in 2 very different conditions. Its going to be a case of new gaskets, rebuild and hope it all works once ive machined them flat again tomorrow. #here goes#



link to some of the pics taken so far
http://smg.photobucket.com/albums/v640/RA11YE/Rebu...
Gassing Station | BMW General | Top of Page | What's New | My Stuff


