Car Seems A Bit Slower After BMW Fixed It
Discussion
I took my car into the local main dealer after the engine fault light came on with reduced power mode. They quickly identified the fault as a split vacuum pipe for the boost pressure sensor. An £80 fix so didn't need to use the insured warranty. They told me they also replaced one of the fuel injectors which was a recall & updated the software.
The car drives fine but feels a bit less urgent than before in the lower part of the rev range. For example I'm sure it pulled a lot stronger in top geap when doing around 50. When taken to the redline it still goes like it should. It also doesn't sound as raspy when blipping the throttle.
Is it my imagination or could anything the garage have done caused this? Car is a non tuned 2007 335i manual.
The car drives fine but feels a bit less urgent than before in the lower part of the rev range. For example I'm sure it pulled a lot stronger in top geap when doing around 50. When taken to the redline it still goes like it should. It also doesn't sound as raspy when blipping the throttle.
Is it my imagination or could anything the garage have done caused this? Car is a non tuned 2007 335i manual.
Tim330 said:
I took my car into the local main dealer after the engine fault light came on with reduced power mode. They quickly identified the fault as a split vacuum pipe for the boost pressure sensor. An £80 fix so didn't need to use the insured warranty. They told me they also replaced one of the fuel injectors which was a recall & updated the software.
The car drives fine but feels a bit less urgent than before in the lower part of the rev range. For example I'm sure it pulled a lot stronger in top geap when doing around 50. When taken to the redline it still goes like it should. It also doesn't sound as raspy when blipping the throttle.
Is it my imagination or could anything the garage have done caused this? Car is a non tuned 2007 335i manual.
My 330i was returned after one of many visits to the dealer with what can generously be described as 100bhp. Despite my best efforts, it wouldn't crack 13 seconds to 60. Apparently a software update had failed. It could be something similar with you, or they may have deliberately reined in the engine to prolong the life of something like the HPFP (our now primes itself when the car is unlocked - who else knows what they have changed)The car drives fine but feels a bit less urgent than before in the lower part of the rev range. For example I'm sure it pulled a lot stronger in top geap when doing around 50. When taken to the redline it still goes like it should. It also doesn't sound as raspy when blipping the throttle.
Is it my imagination or could anything the garage have done caused this? Car is a non tuned 2007 335i manual.
Alternatively, it could be because you have the air con on full!
Derek Chevalier said:
My 330i was returned after one of many visits to the dealer with what can generously be described as 100bhp. Despite my best efforts, it wouldn't crack 13 seconds to 60. Apparently a software update had failed. It could be something similar with you, or they may have deliberately reined in the engine to prolong the life of something like the HPFP (our now primes itself when the car is unlocked - who else knows what they have changed)
Alternatively, it could be because you have the air con on full!
Have you read about BMW reining in the tune on the engine to make it last longer? I hope they wouldn't do something so sneaky. I've never put it on a rolling road so don't know the power before. I suppose its been one of the hottest days of the year, perhaps thats all it is.Alternatively, it could be because you have the air con on full!
Tim330 said:
Derek Chevalier said:
My 330i was returned after one of many visits to the dealer with what can generously be described as 100bhp. Despite my best efforts, it wouldn't crack 13 seconds to 60. Apparently a software update had failed. It could be something similar with you, or they may have deliberately reined in the engine to prolong the life of something like the HPFP (our now primes itself when the car is unlocked - who else knows what they have changed)
Alternatively, it could be because you have the air con on full!
Have you read about BMW reining in the tune on the engine to make it last longer? I hope they wouldn't do something so sneaky. I've never put it on a rolling road so don't know the power before. I suppose its been one of the hottest days of the year, perhaps thats all it is.Alternatively, it could be because you have the air con on full!
http://www.1addicts.com/forums/showthread.php?t=54...
http://www.1addicts.com/forums/showthread.php?t=64...
http://www.autoblog.com/2010/10/12/class-action-su...
Derek Chevalier said:
Mine has less than 250bhp, but that is probably down to the carbon build up rather than BMW modifying anything. However, Google has some interesting links
http://www.1addicts.com/forums/showthread.php?t=54...
http://www.1addicts.com/forums/showthread.php?t=64...
http://www.autoblog.com/2010/10/12/class-action-su...
Oh dear, thats not good reading. I can't see how many HP it would be down with the update. Is it possible to get BMW to roll back an update? I've taken out a BMW insured warranty so don't want to tune the car which would void it.http://www.1addicts.com/forums/showthread.php?t=54...
http://www.1addicts.com/forums/showthread.php?t=64...
http://www.autoblog.com/2010/10/12/class-action-su...
Found this here
Looks like the service bulletin given to the dealer. Seems like the update causes more lag. I'll ask them to put it back to how it was, & probably have to pay for the privilege.
http://www.e90post.com/forums/showthread.php?t=147...
SUBJECT
N54 Distinct Clanking Noise from Turbocharger Area
MODEL
E90, E92 and E93 (3 Series) 335i and 335xi
E60 and E61 (5 Series) 535i and 535xi
All with N54 engine from the start of production up to March 2008 production
SITUATION
The customer complains of a metallic noise from the exhaust system near the engine or turbocharger area. This noise is described as a clanking noise, occurring up to six or seven times in a row during a deceleration from approximately 3,500 RPM; or during a heavy application of the accelerator without a drive gear being engaged.
Complaints received regarding a slight rattle from this area under steady acceleration in the 2,000 RPM to 4,000 RPM range are due to the rotating waste gate valve face; this is a characteristic of the mechanical waste gate. The rotating waste gate valve face is necessary to ensure proper sealing. This slight rattle noise is considered normal operation of the mechanical waste gate valve. No repair should be attempted for this type of rattling complaint.
CAUSE
The wastegate valve does not completely close due to the mechanical tolerances of the wastegate actuator. This results in the wastegate valve repeatedly clanking against its seating surface.
PROCEDURE
Vehicles produced from May 2006 up to September 2007
Do not replace the turbocharger or adjust the existing wastegate actuator control rod.
Perform ISID Test Plan; Noises at Turbocharger (Path: Function Structure – Drive – Mechanism, Noises, Leaks – Noises – Engine Noise – Noises at Turbocharger – Start Search and follow displayed test plan.
The test plan will conclude with an instruction to replace the wastegate actuators; ignore this instruction. Reprogram the DME if the vehicle has not already been programmed to one of the levels described below. Compare the vehicle I-Level to the table below.
Model
Vehicle Data Status
E90, E92, and E93 (335i and 335xi)
E89x-08-03-530 or higher
E60 and E61 (535i and 535xi)
E060-08-03-525 or higher
3. If the vehicle has not achieved one of the levels above, reprogram the vehicle using ISTA/P 2.32.1 or a more recent version.
4. After programming is completed, if the noise is no longer present, take no further action. If the noise is still present, replace both of the turbocharger wastegate actuators in accordance with Repair Instruction RA 11 65 580, Replacing vacuum unit (wastegate) (N54).
Vehicles produced from September 2007 up to March 2008
Do not replace the turbocharger or adjust the existing wastegate actuator control rod.
Perform ISID Test Plan; Noises at Turbocharger (Path: Function Structure – Drive – Mechanism, Noises, Leaks – Noises – Engine Noise – Noises at Turbocharger – Start Search and follow displayed test plan.
The test plan will conclude with an instruction to replace the wastegate actuators; ignore this instruction. Reprogram the DME if the vehicle has not already been programmed to one of the levels described below. Compare the vehicle I-Level to the table below.
Model
Vehicle Data Status
E90, E92, and E93 (335i and 335xi)
E89x-08-03-530 or higher
E60 and E61 (535i and 535xi)
E060-08-03-525 or higher
3. If the vehicle has not already achieved one of the levels above, reprogram the vehicle using ISTA/P 2.32.1 or more recent version.
All 335i/xi and 535i/xi models built from June 2006 up to September 2007
The updated software causes a small amount of increased "turbocharger lag" under certain circumstances and, while not substantial, the lag may be perceptible to the most sensitive BMW drivers. X6, 135i, 3 Series and 5 Series vehicles from March 2008 production onward are not affected. If said "turbocharger lag" is a customer's complaint, then the vehicle's DME software can be retrofitted to the original waste gate operation.
Procedure for vehicles up to September 2007 production:
Using ISTA/P 2.32.1 or a more recent version, select "Conversions", and then select "Wastegate valve conversion". Follow the on-screen prompts to reinstall the original waste gate operation.
After the "Waste gate valve conversion" has been completed, some waste gate-related noise may be detected.
Important Note:
To eliminate the "turbocharger lag" complaint on the vehicles produced from September 2007 up to March 2008 (after programming with Progman versions V29.2 – V32.0), reprogram the complete vehicle, using ISTA/P 2.32.1 or a more recent version.
PARTS INFORMATION
E90, E92, and E93 (3 Series):
Part Number
Description
Quantity
11 65 7 585 745
Actuator Cylinder 1-3
1
11 65 7 585 746
Actuator Cylinder 4-6
1
E60 and E61 (5 Series):
Part Number
Description
Quantity
11 65 7 585 745
Actuator Cylinder 1-3
1
11 65 7 585 747
Actuator Cylinder 4-6
1
WARRANTY INFORMATION
Covered under the terms of the BMW New Vehicle Limited Warranty.
Defect Code:
11 65 05 39 00
Labor Operation:
Labor Allowance:
Description:
Programming/encoding control units
Including CAS
Programming/encoding control units
Not including CAS
Note 1: Should the vehicle be affected at the same time by another repair in which programming of control units is also required, programming may be claimed only once.
Note 2: In the case where Progman requires the replacement of control modules or additional programming because certain control modules failed to program correctly, print out the Measures Plan and Status Report/Final Report as described in the Progman programming procedure (B09 05 01). Attach these reports to the RO in the vehicle file. This additional work should be claimed under the defect code listed in this bulletin using the labor operation and labor allowance from the KSD.
Labor Operation:
Labor Allowance:
Description:
Removing and installing or replacing
both exhaust turbochargers
+11 65 580
Refer to KSD based on model
Adjusting vacuum units and replacing
if necessary
Looks like the service bulletin given to the dealer. Seems like the update causes more lag. I'll ask them to put it back to how it was, & probably have to pay for the privilege.
http://www.e90post.com/forums/showthread.php?t=147...
SUBJECT
N54 Distinct Clanking Noise from Turbocharger Area
MODEL
E90, E92 and E93 (3 Series) 335i and 335xi
E60 and E61 (5 Series) 535i and 535xi
All with N54 engine from the start of production up to March 2008 production
SITUATION
The customer complains of a metallic noise from the exhaust system near the engine or turbocharger area. This noise is described as a clanking noise, occurring up to six or seven times in a row during a deceleration from approximately 3,500 RPM; or during a heavy application of the accelerator without a drive gear being engaged.
Complaints received regarding a slight rattle from this area under steady acceleration in the 2,000 RPM to 4,000 RPM range are due to the rotating waste gate valve face; this is a characteristic of the mechanical waste gate. The rotating waste gate valve face is necessary to ensure proper sealing. This slight rattle noise is considered normal operation of the mechanical waste gate valve. No repair should be attempted for this type of rattling complaint.
CAUSE
The wastegate valve does not completely close due to the mechanical tolerances of the wastegate actuator. This results in the wastegate valve repeatedly clanking against its seating surface.
PROCEDURE
Vehicles produced from May 2006 up to September 2007
Do not replace the turbocharger or adjust the existing wastegate actuator control rod.
Perform ISID Test Plan; Noises at Turbocharger (Path: Function Structure – Drive – Mechanism, Noises, Leaks – Noises – Engine Noise – Noises at Turbocharger – Start Search and follow displayed test plan.
The test plan will conclude with an instruction to replace the wastegate actuators; ignore this instruction. Reprogram the DME if the vehicle has not already been programmed to one of the levels described below. Compare the vehicle I-Level to the table below.
Model
Vehicle Data Status
E90, E92, and E93 (335i and 335xi)
E89x-08-03-530 or higher
E60 and E61 (535i and 535xi)
E060-08-03-525 or higher
3. If the vehicle has not achieved one of the levels above, reprogram the vehicle using ISTA/P 2.32.1 or a more recent version.
4. After programming is completed, if the noise is no longer present, take no further action. If the noise is still present, replace both of the turbocharger wastegate actuators in accordance with Repair Instruction RA 11 65 580, Replacing vacuum unit (wastegate) (N54).
Vehicles produced from September 2007 up to March 2008
Do not replace the turbocharger or adjust the existing wastegate actuator control rod.
Perform ISID Test Plan; Noises at Turbocharger (Path: Function Structure – Drive – Mechanism, Noises, Leaks – Noises – Engine Noise – Noises at Turbocharger – Start Search and follow displayed test plan.
The test plan will conclude with an instruction to replace the wastegate actuators; ignore this instruction. Reprogram the DME if the vehicle has not already been programmed to one of the levels described below. Compare the vehicle I-Level to the table below.
Model
Vehicle Data Status
E90, E92, and E93 (335i and 335xi)
E89x-08-03-530 or higher
E60 and E61 (535i and 535xi)
E060-08-03-525 or higher
3. If the vehicle has not already achieved one of the levels above, reprogram the vehicle using ISTA/P 2.32.1 or more recent version.
All 335i/xi and 535i/xi models built from June 2006 up to September 2007
The updated software causes a small amount of increased "turbocharger lag" under certain circumstances and, while not substantial, the lag may be perceptible to the most sensitive BMW drivers. X6, 135i, 3 Series and 5 Series vehicles from March 2008 production onward are not affected. If said "turbocharger lag" is a customer's complaint, then the vehicle's DME software can be retrofitted to the original waste gate operation.
Procedure for vehicles up to September 2007 production:
Using ISTA/P 2.32.1 or a more recent version, select "Conversions", and then select "Wastegate valve conversion". Follow the on-screen prompts to reinstall the original waste gate operation.
After the "Waste gate valve conversion" has been completed, some waste gate-related noise may be detected.
Important Note:
To eliminate the "turbocharger lag" complaint on the vehicles produced from September 2007 up to March 2008 (after programming with Progman versions V29.2 – V32.0), reprogram the complete vehicle, using ISTA/P 2.32.1 or a more recent version.
PARTS INFORMATION
E90, E92, and E93 (3 Series):
Part Number
Description
Quantity
11 65 7 585 745
Actuator Cylinder 1-3
1
11 65 7 585 746
Actuator Cylinder 4-6
1
E60 and E61 (5 Series):
Part Number
Description
Quantity
11 65 7 585 745
Actuator Cylinder 1-3
1
11 65 7 585 747
Actuator Cylinder 4-6
1
WARRANTY INFORMATION
Covered under the terms of the BMW New Vehicle Limited Warranty.
Defect Code:
11 65 05 39 00
Labor Operation:
Labor Allowance:
Description:
- 61 00 811
Programming/encoding control units
Including CAS
- 61 00 801
Programming/encoding control units
Not including CAS
- Main Work - use this labor operation number when this is the only repair being performed, or if this is the main repair when performed along with other repairs at the same time. If this is not the main repair, refer to KSD for the associated (+) labor operation code.
Note 1: Should the vehicle be affected at the same time by another repair in which programming of control units is also required, programming may be claimed only once.
Note 2: In the case where Progman requires the replacement of control modules or additional programming because certain control modules failed to program correctly, print out the Measures Plan and Status Report/Final Report as described in the Progman programming procedure (B09 05 01). Attach these reports to the RO in the vehicle file. This additional work should be claimed under the defect code listed in this bulletin using the labor operation and labor allowance from the KSD.
Labor Operation:
Labor Allowance:
Description:
- 11 65 048
Removing and installing or replacing
both exhaust turbochargers
+11 65 580
Refer to KSD based on model
Adjusting vacuum units and replacing
if necessary
in theory if the hose to the boost sensor was split the dme would be seeing less boost than there actually was so it would request more boost so your engine would be receiving more boost than it should do, which would eventually throw a code.
its similar in principal to the bodged up tune I done on my old rat saab 9000 2.3t, fit a fish tank bleed off valve in the boost sensor pipe to trick the ecu into requesting more boost, crush the fuel pressure regulator by 1mm in a vice between 2 sockets to up the fuel pressure cut out the cat and weld in a straight pipe drainpipe cold air feed and iced water sprayed onto the intercooler by moving the headlight skooshers. it was a mental old barge.
its similar in principal to the bodged up tune I done on my old rat saab 9000 2.3t, fit a fish tank bleed off valve in the boost sensor pipe to trick the ecu into requesting more boost, crush the fuel pressure regulator by 1mm in a vice between 2 sockets to up the fuel pressure cut out the cat and weld in a straight pipe drainpipe cold air feed and iced water sprayed onto the intercooler by moving the headlight skooshers. it was a mental old barge.
Gassing Station | BMW General | Top of Page | What's New | My Stuff


