Z4 wheel question
Z4 wheel question
Author
Discussion

PaulB81

Original Poster:

883 posts

191 months

Saturday 18th August 2012
quotequote all
Hi all

I recently got a z4 coupe and was just looking at the wheels/tyres as they need a refurb. Then I noticed the fronts are wider than the rears! That cant be right surely? Has someone put them on the wrong way round or are they supposed to be this way? They are 18 inch factory wheels.

Cheers guys
-Paul

Fox-

13,578 posts

277 months

Saturday 18th August 2012
quotequote all
No, this is definately not right. The rears should be wider than the fronts - 225/40/18 front and 255/35/18 on the rear.

PaulB81

Original Poster:

883 posts

191 months

Saturday 18th August 2012
quotequote all
Didnt think so. When I replace the wheels, is it ok to get a set that are the same front and back? Or should I stick with wider rears?

PaulB81

Original Poster:

883 posts

191 months

Saturday 18th August 2012
quotequote all
Oh hang on, maybe I am being a retard?

You say:

225/40/18 front and 255/35/18 on the rear.

so 225/40/18 is NARROWER than 255/35/18 on the rear

I assumed bigger number meant wider?

motco

17,670 posts

277 months

Saturday 18th August 2012
quotequote all
PaulB81 said:
Oh hang on, maybe I am being a retard?

You say:

225/40/18 front and 255/35/18 on the rear.

so 225/40/18 is NARROWER than 255/35/18 on the rear

I assumed bigger number meant wider?
225 & 255 relates to the width I believe, and the 35 or 40 the aspect ratio (profile. Either way the wider ones are for the back without a doubt.

PaulB81

Original Poster:

883 posts

191 months

Saturday 18th August 2012
quotequote all
Why would the profile be 35 on the back and 40 on the front?

motco

17,670 posts

277 months

Saturday 18th August 2012
quotequote all
Because the figure is a ratio of width to a figure related to diameter AFAIK

Some US website said:
55 is a tricky number to derive; it is a percentage; the ratio between the width of the tire and its sidewall height. Those ultra- low-profile tires so popular today, that appear to be flat but aren't, will have a lower number here, such as 35, as their sidewalls are so short.
Edited by motco on Saturday 18th August 11:43

DSM2

3,624 posts

231 months

Saturday 18th August 2012
quotequote all
PaulB81 said:
Why would the profile be 35 on the back and 40 on the front?
To keep the rolling diameter near enough the same.

225/40 = 90mm tyre height.

255/35 = 89.25 mm tyre height.

Doubled and added to the rim diam gives the overall diameter, the same within 1mm.


DSM2

3,624 posts

231 months

Saturday 18th August 2012
quotequote all
motco said:
Because the figure is a ratio of width to a figure related to diameter AFAIK

Some US website said:
55 is a tricky number to derive; it is a percentage; the ratio between the width of the tire and its sidewall height. Those ultra- low-profile tires so popular today, that appear to be flat but aren't, will have a lower number here, such as 35, as their sidewalls are so short.
Edited by motco on Saturday 18th August 11:43
It's quiet straight forward. The sidewall height is expressed as a percentage of the section width.

I.e. 255 x 35% = sidewall height of 89.25mm.