E46 Clicking noise from rear on right hand bends
E46 Clicking noise from rear on right hand bends
Author
Discussion

Gad-Westy

Original Poster:

16,666 posts

244 months

Monday 24th September 2012
quotequote all
Seem to be on a role with fixing my BM's at the moment so thought I might tackle whatever is causing this next.

Basically when negotiating a long right hand bend, particularly roundabouts. I seem to be getting a a clicking/ticking noise from the NS rear of the car.

Is this likely to be drive shaft or diff related or something to do with the suspension?



Robatr0n

12,362 posts

247 months

Monday 24th September 2012
quotequote all
Could be a CV joint on it's way out (mine sounded like this before it needed replacing) or would be a cracked rear spring which I think (IIRC?) is common on the E46.

Gad-Westy

Original Poster:

16,666 posts

244 months

Monday 24th September 2012
quotequote all
Robatr0n said:
Could be a CV joint on it's way out (mine sounded like this before it needed replacing) or would be a cracked rear spring which I think (IIRC?) is common on the E46.
Cheers. Had a few cracked rear spring but never noticed this noise before. Worth a check though as should be easy to spot. Cheers.

Robatr0n

12,362 posts

247 months

Monday 24th September 2012
quotequote all
Definitely worth checking the CV joint too. If the gator is split or you can see grease ouzing out of it there's a good chance it's knackered.

Gad-Westy

Original Poster:

16,666 posts

244 months

Monday 24th September 2012
quotequote all
Robatr0n said:
Definitely worth checking the CV joint too. If the gator is split or you can see grease ouzing out of it there's a good chance it's knackered.
Cheers, how big a job is a CV joint on these?

buggalugs

9,297 posts

268 months

Monday 24th September 2012
quotequote all
Not too bad, you need an inverse torx thing for the driveshaft to diff flange bolts, and the hub nut is VERY tight i.e. I broke my halfords pro breaker bar tight. I borrow a 3/4" socket and bar when I need to do that bolt! The drive splines can be tight in the hub also but a lump hammer being careful about the threads, or a 2/3 leg puller can push it out. Having done one before I'd say 1.5-2 hours on axle stands, longer for first time.

Gad-Westy

Original Poster:

16,666 posts

244 months

Monday 24th September 2012
quotequote all
buggalugs said:
Not too bad, you need an inverse torx thing for the driveshaft to diff flange bolts, and the hub nut is VERY tight i.e. I broke my halfords pro breaker bar tight. I borrow a 3/4" socket and bar when I need to do that bolt! The drive splines can be tight in the hub also but a lump hammer being careful about the threads, or a 2/3 leg puller can push it out. Having done one before I'd say 1.5-2 hours on axle stands, longer for first time.
Sounds good to me. 3/4" sockets at the ready! Will get it jacked up later in the week and have a poke around.

steve_bmw

1,591 posts

206 months

Monday 24th September 2012
quotequote all
i had a rubbing/clicking noise on the z4 last week coming from the n/s rear, it was a stone stuck in-between the backplate and the disc.
take the wheel off and have a look.

Gad-Westy

Original Poster:

16,666 posts

244 months

Monday 24th September 2012
quotequote all
steve_bmw said:
i had a rubbing/clicking noise on the z4 last week coming from the n/s rear, it was a stone stuck in-between the backplate and the disc.
take the wheel off and have a look.
Cheers. Will look out for something like that. That would be a nice problem to have!