help M3 lower rear wishbone removal
help M3 lower rear wishbone removal
Author
Discussion

Warwick67

Original Poster:

418 posts

245 months

Friday 5th October 2012
quotequote all
Can anyone out there shed some light on how to get the rear lower wishbone of an E46 M3 convertible? The attachment bolt won't come out due to the drive shaft being to close, see pic...
Any help / tips gratefully received....

E30M3SE

8,493 posts

227 months

Friday 5th October 2012
quotequote all
Either lower the diff or undo the bolts holding the driveshaft to the diff.

Warwick67

Original Poster:

418 posts

245 months

Saturday 6th October 2012
quotequote all
Just come from a TVR to this and people say a TVR is not built for maintenance. Can't believe you have to attack the diff / drive shaft to get the wishbone off...

stuart-b

3,651 posts

257 months

Saturday 6th October 2012
quotequote all
Looking at that picture, if you really wanted to avoid removing the drive shaft, is it possible to grind the bolt in half, and get it out, then when you put the new wishbone back in, partially screw the bolt on before putting it back?

Rollcage

11,345 posts

223 months

Saturday 6th October 2012
quotequote all
You are luck it's not a Mondeo N/S/F. Got to move the gearbox to do those properly! hehe

As said, either lower the diff or undo the drive shaft.

Warwick67

Original Poster:

418 posts

245 months

Monday 8th October 2012
quotequote all
Cheers gents....

So, in the end I cut it off, procured another bolt of the same spec but with a loose washer and slightly shorter but still with full bolt engagement. Job done, minimum hassle.....

stuart-b

3,651 posts

257 months

Monday 8th October 2012
quotequote all
Warwick67 said:
Cheers gents....

So, in the end I cut it off, procured another bolt of the same spec but with a loose washer and slightly shorter but still with full bolt engagement. Job done, minimum hassle.....
thumbup Yep, as I said, cut the bugger off.

E30M3SE

8,493 posts

227 months

Monday 8th October 2012
quotequote all
Warwick67 said:
Cheers gents....

So, in the end I cut it off, procured another bolt of the same spec but with a loose washer and slightly shorter but still with full bolt engagement. Job done, minimum hassle.....
The bolt you used was of the corrct tensile strength, of 10.9, wasn't it?

iSore

4,011 posts

175 months

Monday 8th October 2012
quotequote all
Undoing the driveshaft from the diff takes 10 minutes. Why was there cutting involved?

stuart-b

3,651 posts

257 months

Monday 8th October 2012
quotequote all
iSore said:
Undoing the driveshaft from the diff takes 10 minutes. Why was there cutting involved?
Hmm might be wrong here but I was under the impression that you needed to replace the bolts if removing the drive shaft... at least, I had to on an old Porsche. Might not be the same? Just more hassle than wizzing the bolt off and putting another one in.

helix402

7,913 posts

213 months

Monday 8th October 2012
quotequote all
No need to replace the driveshaft bolts.

Warwick67

Original Poster:

418 posts

245 months

Tuesday 9th October 2012
quotequote all
Yes bolt was the correct spec. Drive shaft bolts require a special spline type socket...

iSore

4,011 posts

175 months

Tuesday 9th October 2012
quotequote all
Warwick67 said:
Yes bolt was the correct spec. Drive shaft bolts require a special spline type socket...
It's an ordinary torx, T12 or T14, available anywhere. A drop of threadlock on each and retighten, easy.