e36 328 EBD comms issues
Discussion
Just wondering if any of you have any experience of these from the distant past.
I have an e36 328 1998 as above & when I connect to the comms port in the engine bay I get comms errors, and I did not used to!
In searching t'interwebs it seems that there should be an OBD port down by the bonnet release alas mine is my track car & there is no dash, so I am wondering if I either tucked it away somewhere when removing it, or didn't notice the socket & pulled something like a link cable off.
I have been trawling through the Bentley manual I have electronically, alas I am not yet even finding the correct wiring drawing showing the comms port, never mind the EBD port.
I am wondering if anyone either has experience of comms issues with this car, or can help with a wiring diagram.
I have an e36 328 1998 as above & when I connect to the comms port in the engine bay I get comms errors, and I did not used to!
In searching t'interwebs it seems that there should be an OBD port down by the bonnet release alas mine is my track car & there is no dash, so I am wondering if I either tucked it away somewhere when removing it, or didn't notice the socket & pulled something like a link cable off.
I have been trawling through the Bentley manual I have electronically, alas I am not yet even finding the correct wiring drawing showing the comms port, never mind the EBD port.
I am wondering if anyone either has experience of comms issues with this car, or can help with a wiring diagram.
From my research;
Late model (96/97 on iirc) American spec vehicles had an in dash OBD connector of the trapezium style like most modern cars. No EU spec car ever had this, and only had the underbonnet one.
The comms port under the bonnet can be a bit flaky and gets dirty easily. It's worth giving it a good blast with an electronic contact cleaner or brake cleaner if you can't get hold of that. Mine was a bit temperamental until I cleaned it, and I then installed an adapter and Bluetooth OBD2 dongle so I didn't have to keep removing the plug.
What errors do you see on the OBD?
Late model (96/97 on iirc) American spec vehicles had an in dash OBD connector of the trapezium style like most modern cars. No EU spec car ever had this, and only had the underbonnet one.
The comms port under the bonnet can be a bit flaky and gets dirty easily. It's worth giving it a good blast with an electronic contact cleaner or brake cleaner if you can't get hold of that. Mine was a bit temperamental until I cleaned it, and I then installed an adapter and Bluetooth OBD2 dongle so I didn't have to keep removing the plug.
What errors do you see on the OBD?
Thanks guys, at least it appears I am not missing something, although something has definitely changed.
I have 3 devices to connect to the comms port.
1 x airbag only reset tool, which works.
1 x engine only scanning tool, which now does not, but did use to.
1 x full system code reader (ebay £50) which now also does not work, but did.
I will give it a good clean & check the error codes to be more precise, but they were all basically not connecting & saying some version of is the car equipped, switch off & try again.
I have 3 devices to connect to the comms port.
1 x airbag only reset tool, which works.
1 x engine only scanning tool, which now does not, but did use to.
1 x full system code reader (ebay £50) which now also does not work, but did.
I will give it a good clean & check the error codes to be more precise, but they were all basically not connecting & saying some version of is the car equipped, switch off & try again.
Ok, so at long last (sorry) an update.
Found the wiring diagram & remembered an issue I have with the instrument console when I saw it on the diagram, so swapped it for a spare I have & then managed to get the ebay cheapie to connect & work 100%.
Alas my Autel MS 590 still refuses to connect & just says pairing failed try again.
I then tried my new Innovate OT-2, which was the real reason for connecting & that does not connect either, I have contacted their customer support & they suggested changing a few settings on the interface, but as I couldn't get the Autel to connect I was not surprised that this failed.
I guess it is a case of more of the same checking on Monday when I can get back to it.
Found the wiring diagram & remembered an issue I have with the instrument console when I saw it on the diagram, so swapped it for a spare I have & then managed to get the ebay cheapie to connect & work 100%.
Alas my Autel MS 590 still refuses to connect & just says pairing failed try again.
I then tried my new Innovate OT-2, which was the real reason for connecting & that does not connect either, I have contacted their customer support & they suggested changing a few settings on the interface, but as I couldn't get the Autel to connect I was not surprised that this failed.
I guess it is a case of more of the same checking on Monday when I can get back to it.
Sorry to report (name change) I did not.
I had what you bought & it worked fine up until about a year ago (ISH) and I have had a comms fault ever since that I can't get to the bottom af because it won't communicate.
It is definitely the car as another type that I borrowed did the same.
When it worked it did do everything that it should though.
I had what you bought & it worked fine up until about a year ago (ISH) and I have had a comms fault ever since that I can't get to the bottom af because it won't communicate.
It is definitely the car as another type that I borrowed did the same.
When it worked it did do everything that it should though.
Gassing Station | BMW General | Top of Page | What's New | My Stuff


