F30 X-Drive tyre wear
Discussion
My F30 X-Drive has 15k on it now and it's still on it's original Pirelli run flats which I intend to change soon due to wear.
Fronts 2.5mm
Backs 3.5mm
Problem is the outside blocks on my fronts have virtually gone completely and I can't imagine this is right while the backs have even wear right across.
is this the way X-Drives wear their tyres?
is it the design of the run flat tyre at fault?
or is the camber on the front out a little as the drivers side is worse than the passenger, normally the reverse is true due to clockwise round abouts?
The car is still under warranty so I will be asking BMW
Fronts 2.5mm
Backs 3.5mm
Problem is the outside blocks on my fronts have virtually gone completely and I can't imagine this is right while the backs have even wear right across.
is this the way X-Drives wear their tyres?
is it the design of the run flat tyre at fault?
or is the camber on the front out a little as the drivers side is worse than the passenger, normally the reverse is true due to clockwise round abouts?
The car is still under warranty so I will be asking BMW
Your wear rate seems pretty high to me. My original Bridgestone Potenza RFTs lasted 20-22k rear and would have been around 35k on the fronts, had I not ditched them for a full set of MPSS non-runflats.
My front wear was pretty even, but the rears had both worn the inside edge. The dealer felt this was due to hard cornering or low tyre pressures. I think it was probably a combination of the two as I tended to run the Potenzas below recommended pressure to make the ride a little more tolerable.
This is a 335d F30 which had standard springs for the first half of the life of these tyres, and ACS springs for the remainder. I drive relatively quickly.
My front wear was pretty even, but the rears had both worn the inside edge. The dealer felt this was due to hard cornering or low tyre pressures. I think it was probably a combination of the two as I tended to run the Potenzas below recommended pressure to make the ride a little more tolerable.
This is a 335d F30 which had standard springs for the first half of the life of these tyres, and ACS springs for the remainder. I drive relatively quickly.
Edited by 335d on Thursday 22 December 00:07
Chewed outside shoulders at the front happen easily on modern BMWs. They don't run quite enough camber to prevent the sidewall from flexing too much under high lateral load. Sometimes running slightly higher pressure than recommended can help as well as choosing a higher load tyre and/or a tyre with inherently stiffer sidewalls, ie not Michelin. If you plan to drop the RFTs, the Yokohama 105s fits the bill if they do the size required.
Edited by nickfrog on Thursday 22 December 16:13
I want to change to Eagle F1's but I don't want to put 4 new tyres on and find they wear the same way on the front.
I am no running 2.8bar all round in an effort to get them to last another couple of thousand miles.
I would like a little more camber on the front if this fixes the uneven wear, this would also help the little bit of understand the car has which is now very apparent due to the cold greasy roads and the worn tyres.
I am no running 2.8bar all round in an effort to get them to last another couple of thousand miles.
I would like a little more camber on the front if this fixes the uneven wear, this would also help the little bit of understand the car has which is now very apparent due to the cold greasy roads and the worn tyres.
On closer inspection the front tyres are just wearing more on the outside than the inside, the outside has next to nothing left, the middle has 2.5mm and the inside has 3.5mm. Very odd to have the tyres wear like that, slightly faster wear on the inside is the best for grip from the tyres. The answer to the problem would be another 0.5deg of camber but as it can't be done easily I'll probably just have to live with it though will be mentioning it to my BMW dealer.
Gassing Station | BMW General | Top of Page | What's New | My Stuff



