X5 rear bumper removal
Discussion
I have a slight dent in the rear bumper of my 3.0 Sport X5 which I'm sure I could fix if I could get the bumper off. I've had a look and undone the 2 Torx screws near the exhausts and the screws in the wheel arch but can't seem to budge it. I can see a couple of clips but not sure if/how these are unclipped
Wondering if anyone can help me by explaining the process to get it off
Thanks
Wondering if anyone can help me by explaining the process to get it off
Thanks
According to a post on x-outpost:
You need to remove (2) T55 Torx
head sockets you'll see located just above exhaust tips.
Then remove (2 ea.) 8mm screws in well behind each rear wheel.
With a person on each side, the bumper slides right off.
Install in reverse. You'll see a bracket on each side, just be sure to line up
the slots.
Regards, Gary
You need to remove (2) T55 Torx
head sockets you'll see located just above exhaust tips.
Then remove (2 ea.) 8mm screws in well behind each rear wheel.
With a person on each side, the bumper slides right off.
Install in reverse. You'll see a bracket on each side, just be sure to line up
the slots.
Regards, Gary
Did you pop out the rear section underneath that connects to the undertray?
if you have parking sensors its best to disconnect them from the inside first and thread the loom out when you remove the bumper. To access this, remove the right hand side storage panel and feel straight down for the grommet of the sensor loom. Follow this wore up to the control unit where the loom plugs in. The plug is a cam-over style plug so using a small flat bladed screwdriver, lift the "saddle" of the plug retainer and move it 90 degrees, the plug will disengage it self as this happens.
I find when removing X5 bumpers to remove the exhaust bezel trim and drop the exhausts from their mounts, this allows a decent amount of room to access the T55's which are a pain to get to.
if you have parking sensors its best to disconnect them from the inside first and thread the loom out when you remove the bumper. To access this, remove the right hand side storage panel and feel straight down for the grommet of the sensor loom. Follow this wore up to the control unit where the loom plugs in. The plug is a cam-over style plug so using a small flat bladed screwdriver, lift the "saddle" of the plug retainer and move it 90 degrees, the plug will disengage it self as this happens.
I find when removing X5 bumpers to remove the exhaust bezel trim and drop the exhausts from their mounts, this allows a decent amount of room to access the T55's which are a pain to get to.
Bumping this old topic as I have a 2008 E70 sport that at some point has suffered a low speed rear impact (no obvious damage) and I have just been informed that the reason the rear bumper is poorly fitting is because the previous owner (or somebody working for them) has made such a horlicks of trying to get the 4 plastic clips back in pace after they had obviously popped out that they have snapped off one and damaged 2 more. You apparently have to remove the whole bumper to do it right at a cost of £200ish so not uncommon for owners to try to ram them back in the wrong way!
Now I'm not too chuffed at this and ultimately staring at a new rear bumper with working clips. This looks and feels like a £1,000+ hit as suspect BMW will want at least £500 for the shoddy bumper (google and see how many E70 drivers have a problem with the rear bumper popping out with the flimsy clips) and then the same again to have it spray painted off car and then switched over.
I could save a bit if I bought a salvage bumper and got it painetd or more still if I hit the jackpot and found a salvage in Carbon Black in A1 nick but any advice on the best way to get this sorted in these austerity times as bet others have had the same issue
Now I'm not too chuffed at this and ultimately staring at a new rear bumper with working clips. This looks and feels like a £1,000+ hit as suspect BMW will want at least £500 for the shoddy bumper (google and see how many E70 drivers have a problem with the rear bumper popping out with the flimsy clips) and then the same again to have it spray painted off car and then switched over.
I could save a bit if I bought a salvage bumper and got it painetd or more still if I hit the jackpot and found a salvage in Carbon Black in A1 nick but any advice on the best way to get this sorted in these austerity times as bet others have had the same issue
If you live in London I can recommend a body shop in NW London that are reasonably priced and know their way around BMW's (they do a lot of work for main dealers). He has to do some work to my X5's rear bumper when SWMBO reversed into a black cab...........and yes we do have PDC and a reversing camera.
Cheib said:
If you live in London I can recommend a body shop in NW London that are reasonably priced and know their way around BMW's (they do a lot of work for main dealers). He has to do some work to my X5's rear bumper when SWMBO reversed into a black cab...........and yes we do have PDC and a reversing camera.
Thanks CheibI am not too far from London (west far better for me than east as work in Reading) and ultimtaley looking for a cost effective solution. I park on a street at a station every other day and can easily envisage me getting this fixed and coming back one day to find someone has nudged me when parking and popped the dreaded clips out which needs the bumper to be removed to resolve. Maybe I am being overly simplistic, but I'm thinking that I just need the cheapest way to find a way of getting a replacement bumper sourced and ready in Carbon Black and then it should take no more than 2 hours at a facility to get the current bumper taken off and new one installed. That way must surely also be pretty easy for a bodyshop as zero masking, etc and they can take the new bumper into a controlled environment for spraying without 2 tonnes of other car and paint coming too!
thegreatdogwood said:
Cheib said:
If you live in London I can recommend a body shop in NW London that are reasonably priced and know their way around BMW's (they do a lot of work for main dealers). He has to do some work to my X5's rear bumper when SWMBO reversed into a black cab...........and yes we do have PDC and a reversing camera.
Thanks CheibI am not too far from London (west far better for me than east as work in Reading) and ultimtaley looking for a cost effective solution. I park on a street at a station every other day and can easily envisage me getting this fixed and coming back one day to find someone has nudged me when parking and popped the dreaded clips out which needs the bumper to be removed to resolve. Maybe I am being overly simplistic, but I'm thinking that I just need the cheapest way to find a way of getting a replacement bumper sourced and ready in Carbon Black and then it should take no more than 2 hours at a facility to get the current bumper taken off and new one installed. That way must surely also be pretty easy for a bodyshop as zero masking, etc and they can take the new bumper into a controlled environment for spraying without 2 tonnes of other car and paint coming too!
t you. Denis O said:
Thanks but I couldn't see any mention of the E70 X5??Denis O said:
Sorry about that. With 2 of the buggers I tend to think e53 all the time.
Perhaps there are similarities.
No worries DenisPerhaps there are similarities.
What I really need to know is whether a 2011 model rear sport bumper is the same as a 2008 model as I have seen one but don't know if they changed this part when the car was facelifted in 2010
Gassing Station | BMW General | Top of Page | What's New | My Stuff



