Front wheel alignment
Front wheel alignment
Author
Discussion

2wheelsjimmy

Original Poster:

624 posts

128 months

Wednesday 15th February 2017
quotequote all
So I think my front wheel is out of alignment with the handlebars by a tiny amount. So small I could now be imagining it.
I took the forks out again at the weekend and reinstalled everything as per the manual.
Torque retaining axle bolt, pump up and down on front forks, tighten axle pinch bolts. But I still think it's out a tiny bit.

Before I take it to a mechanic (to be told it's fine), is there a way to accurately find out if it's out of alignment?

I thought about lining handlebars straight and then using string line to rear wheel, but that brings rear wheel alignment into equation.


TooLateForAName

4,935 posts

215 months

Wednesday 15th February 2017
quotequote all
Out of alignment with the yokes or the bars? Any possibility of the bars being slightly bent?

HustleRussell

26,715 posts

191 months

Wednesday 15th February 2017
quotequote all
I've had this before and reached the conclusion that I'm just as likely to have one arm longer than the other.

2wheelsjimmy

Original Poster:

624 posts

128 months

Wednesday 15th February 2017
quotequote all
The yokes and then bars. I ride an smt 990 so the bars bolt onto the yokes.
I don't think it's arm length, as the left side handlebar appears to be a few more further forward than the right, when the front wheel is forward.
I've tried to use the handbook method to set everything up a few times now, but end up at the same situation, just feeling the handlers are slightly turned with left side further forward than right when wheel is steaight. Or if handlebars are straight and top triple clamp straight then front wheel points slight left.
We're not taking big amounts, millimetres. Some people might not even notice, I think I'm just sensitive to such things.

I don't think the bars are bent, I did drop the bike off the side stand when backing it into garage into right handlebar, so it's possible this has been bent back towards me. But I didn't notice and issue, the issue only came about after I had the suspension out to service it.
If the handlebar was bent the top triple clamp would be inline with front wheel, but visually these appear a few mm out too.
I did libe the handlebars and clamp straight and measure from them to a fixed point on the centre rear of the bike and those measurements were the same, so I concluded the handlebars are fine and it's the wheel/triple clamp miss alignment.


Edited by 2wheelsjimmy on Wednesday 15th February 12:43

Brummmie

5,284 posts

252 months

Wednesday 15th February 2017
quotequote all
Straight edge (or string line) from back wheel to front, see where the steering wheel ends up!

Mike600F

1,049 posts

187 months

Wednesday 15th February 2017
quotequote all
How new are your tyres? Majorly squared off tyres might affect the wheel alignment when you pump the forks as the tyre tends to wear more on the right thanks to the camber of the road.

2wheelsjimmy

Original Poster:

624 posts

128 months

Wednesday 15th February 2017
quotequote all
Tyres only have 500miles on them, if that.

I was looking for a method more accurate than the string one, as it relies on rear wheel alignment. I'm sure my rear wheel is aligned straight, but I'd rather test the front wheel alignment independent if I can.

I've got the MOT next week, so maybe I'll just wait and see if they pick anything up. And if not ask them so just ride it and see what they think.

The issue is, we're talking less than millimetres, a small amount to discern.

Brummmie

5,284 posts

252 months

Wednesday 15th February 2017
quotequote all
Nothing wrong with string line, your frame and swingarm can be pointing in different directions due to manufacturing tolerances, 1st thing to do on a new race bike was to do this, and mark on the swingarm where actual dead ahead is relative to the front wheel.
But you can actually get an alloy straight edge that clamps on.

Edited by Brummmie on Wednesday 15th February 13:57

2wheelsjimmy

Original Poster:

624 posts

128 months

Wednesday 15th February 2017
quotequote all
Brummmie said:
But you can actually get an alloy straight edge that clamps on.

Edited by Brummmie on Wednesday 15th February 13:57
What's your technique?

Clamp on flat edge onto end of swing arm? (with rear wheel removed) Then loop string around front wheel, possibly looped around another straight edge resting up against front wheel, with string under tension?

I've seen different methods, sure they've all merit.

Brummmie

5,284 posts

252 months

Wednesday 15th February 2017
quotequote all
No clamp to the rear tyre, then you want to get the front wheel parallel to the straight edge, you can then actually look at the swinging arm marks and see what straight ahead is. You want both wheels pointing in the same direction, even if they end up slightly off set.

Biker's Nemesis

41,489 posts

239 months

Wednesday 15th February 2017
quotequote all
I've used the string method since the early 1980's

2wheelsjimmy

Original Poster:

624 posts

128 months

Wednesday 15th February 2017
quotequote all
Right okay thanks. Will give that a crack and see what becomes.

Wedg1e

27,048 posts

296 months

Thursday 16th February 2017
quotequote all
Biker's Nemesis said:
I've used the string method since the early 1980's
I used the Asda bag and laggy band method in the early 1980's whistle


Biker's Nemesis

41,489 posts

239 months

Thursday 16th February 2017
quotequote all
Wedg1e said:
I used the Asda bag and laggy band method in the early 1980's whistle
ASDA in the early 1980s? You're doc brown back from the future ain't ya.

mgv8

1,657 posts

302 months

Thursday 16th February 2017
quotequote all
I was given the method of, loosen the front yoke and bound the front up and down. If everything is as it should be will lines itself back up. This did work for me but at your own risk.

Biker's Nemesis

41,489 posts

239 months

Thursday 16th February 2017
quotequote all
mgv8 said:
I was given the method of, loosen the front yoke and bound the front up and down. If everything is as it should be will lines itself back up. This did work for me but at your own risk.
I do that after a crash to get things in line

2wheelsjimmy

Original Poster:

624 posts

128 months

Thursday 16th February 2017
quotequote all
Yeah seen that, if you just loosen the pinch bolts off a bit it's not going to fall down. Just don't undo them.

Rubin215

4,202 posts

187 months

Thursday 16th February 2017
quotequote all
If you're going to do it properly, you need to drop the front wheel out, loosen the top nut on the steering stem and loosen the clamp bolts on your yokes.

Torque the bottom yoke first, top yoke second then the stem nut.
Loosen the top yoke again and then torque it again, loosen the stem nut again and then torque it again. Now check the height of the forks in the yoke; either level with or x mm above; you would be surprised how many bikes have the forks at different heights, even from brand new!

Now put the front wheel back in again torqueing the axle and any clamp bolts properly.

The alignment of the top and bottom yokes is your starting point; you can't do this with the pinch bolts or stem nut tight.

Loosening and retightening is often missed out too, but means that the top yoke is fully hard down against the nut locking the head bearing tension.

shielsy

826 posts

160 months

Thursday 16th February 2017
quotequote all
I've also had success on both KTM and Hayabusa using the bouncy-bouncy method. It went something like this:

- Loosen everything below top yoke. This includes the bottom yoke, axle and the front arch/mudguard
- Straighten it up by eye
- Bouncy
- Bouncy
- Torque everything back up
- Drink beer

Tip: don't use the front brake while doing bouncy-bouncy

Edited by shielsy on Thursday 16th February 19:52