ZX9 B Engine help - Will on fire on 1,4
Discussion
Fitted a ZX9 B engine to my Westfield and now have an issue.
It will FIRE on cylinders 1-4
Won't fire on 2-3
We have fitted the 100 ohm resistor for the ignition
When removed the engine will NOT turn over.
When fitted we get the above result - 1,4 fire but 2,3 don't.
Tried another ECU, Crank sensor
Re wired 2,3 coils but no joy
Swapped the coils over from 1,4 to 2,3 and 2,3 WILL FIRE and 1,4 don't.
Going to recheck the earths and change the resistor - It was an ebay resistor so if its incorrect ohms i assume it won't fire all 4.
Cylinders 2,3 are controlled by the ecu.
Any help or input would be hugely appreciated.
TheHighlander said:
Fitted a ZX9 B engine to my Westfield and now have an issue.
It will FIRE on cylinders 1-4
Won't fire on 2-3
We have fitted the 100 ohm resistor for the ignition
When removed the engine will NOT turn over.
When fitted we get the above result - 1,4 fire but 2,3 don't.
Tried another ECU, Crank sensor
Re wired 2,3 coils but no joy
Swapped the coils over from 1,4 to 2,3 and 2,3 WILL FIRE and 1,4 don't.
Going to recheck the earths and change the resistor - It was an ebay resistor so if its incorrect ohms i assume it won't fire all 4.
Cylinders 2,3 are controlled by the ecu.
Any help or input would be hugely appreciated.
When you say ecu do you mean cdi?It will FIRE on cylinders 1-4
Won't fire on 2-3
We have fitted the 100 ohm resistor for the ignition
When removed the engine will NOT turn over.
When fitted we get the above result - 1,4 fire but 2,3 don't.
Tried another ECU, Crank sensor
Re wired 2,3 coils but no joy
Swapped the coils over from 1,4 to 2,3 and 2,3 WILL FIRE and 1,4 don't.
Going to recheck the earths and change the resistor - It was an ebay resistor so if its incorrect ohms i assume it won't fire all 4.
Cylinders 2,3 are controlled by the ecu.
Any help or input would be hugely appreciated.
Unless I'm reading it wrong it sounds like you have a dodgy coil.
Edited by Jazoli on Tuesday 28th February 21:24
The problem moved when we changed the wiring for the coils.
Both sets of coils are working fine.
The ecu should fire 2,3 but it's not.
I've swapped out the CDI and it's the same issue.
We can get 2,3 to fire when we use the wiring off 1,4 so it's NOT cool pack related as we have also tried other coils.
Hoping it's a loom issue. It's something stupid anyway.
It's a custom made loom so hoping it's an earth issue somewhere
Both sets of coils are working fine.
The ecu should fire 2,3 but it's not.
I've swapped out the CDI and it's the same issue.
We can get 2,3 to fire when we use the wiring off 1,4 so it's NOT cool pack related as we have also tried other coils.
Hoping it's a loom issue. It's something stupid anyway.
It's a custom made loom so hoping it's an earth issue somewhere
TheHighlander said:
It's a custom made loom so hoping it's an earth issue somewhere
There's your answer.... 99% it's a wasted spark system with only 2 coil driver outputs.
So one output will drive the coils on cylinders 1&4 whereas the other drives coils 2&3
If you've moved coils and changed the ecu & cdi there's a good chance that the drivers side of the ecu isn't connected to the coil or cdi.
If you know the pinout of the ecu run a temp wire from the ecu connection to the cdi.
TheHighlander said:
The problem moved when we changed the wiring for the coils.
Both sets of coils are working fine.
The ecu should fire 2,3 but it's not.
I've swapped out the CDI and it's the same issue.
We can get 2,3 to fire when we use the wiring off 1,4 so it's NOT cool pack related as we have also tried other coils.
Hoping it's a loom issue. It's something stupid anyway.
It's a custom made loom so hoping it's an earth issue somewhere
Right, so I wasn't being a little slow, we only had half the information!Both sets of coils are working fine.
The ecu should fire 2,3 but it's not.
I've swapped out the CDI and it's the same issue.
We can get 2,3 to fire when we use the wiring off 1,4 so it's NOT cool pack related as we have also tried other coils.
Hoping it's a loom issue. It's something stupid anyway.
It's a custom made loom so hoping it's an earth issue somewhere
As Steve says, it's most likely to be the wiring but it could also be the ECU. I assume what you have done is simply swapped the LT leads from each coil and looked to see which cylinders spark. For me, the next move is the temp wire approach suggested by Steve but I would do two wires so I can swap the feeds from one coil to the other. That would either totally prove it's the wiring (correct connection - all 4 work) or prove it's the ECU, or further up-stream (correct or swapped connection, 2 fail but move with the swapped lead.)
I have 2 CDI units and the issue is on both.
The B only has 2 coils as such which control the 4 cylinders 1,4 and the other is 2,3.
We are so close, it winds over and splutters but with no spark to 2,3 it won't start.
We will go over all the earths and try the above also.
I will let you know how we get on.
Thanks again for your help.
The B only has 2 coils as such which control the 4 cylinders 1,4 and the other is 2,3.
We are so close, it winds over and splutters but with no spark to 2,3 it won't start.
We will go over all the earths and try the above also.
I will let you know how we get on.
Thanks again for your help.
Edited by TheHighlander on Wednesday 1st March 09:30
TheHighlander said:
I have 2 CDI units and the issue is on both.
The B only has 2 coils as such which control the 4 cylinders 1,4 and the other is 2,3.
We are so close, it winds over and splutters but with no spark to 2,3 it won't start.
We will go over all the earths and try the above also.
I will let you know how we get on.
Thanks again for your help.
Then it's most likely the trigger from the ECU to the cdi for cylinders 2& 3 or the wires to the coils from the CDi.The B only has 2 coils as such which control the 4 cylinders 1,4 and the other is 2,3.
We are so close, it winds over and splutters but with no spark to 2,3 it won't start.
We will go over all the earths and try the above also.
I will let you know how we get on.
Thanks again for your help.
Edited by TheHighlander on Wednesday 1st March 09:30
Easy to test the wires, you just need to know the ecu pinouts.
And regarding earhts, most systems use a switched negative drive. So there's a permanent positive from the ecu and the negative is switched in the ecu.
One other thing....
make sure the trigger for the ecu is a single sensor, not two @ 180 degrees on the crank. if there are 2, you'll need to check the sensor & wiring
Edited by Steve Bass on Wednesday 1st March 14:38
Gassing Station | Biker Banter | Top of Page | What's New | My Stuff


