Bleeding brakes
Author
Discussion

A500leroy

Original Poster:

8,623 posts

149 months

Thursday 16th March 2017
quotequote all
Something I should tackle myself and learn how to do or pay someone?
Easy task?

obscene

5,180 posts

216 months

Thursday 16th March 2017
quotequote all
Do it yourself, it's an easy job.

TooMany2cvs

29,008 posts

157 months

Thursday 16th March 2017
quotequote all
Why do they need bleeding...?

Because you've replaced something in the hydraulics? Because you're changing the fluid? Or...?

What car? Some ABS systems can be a bit technical.

A500leroy

Original Poster:

8,623 posts

149 months

Thursday 16th March 2017
quotequote all
Can see an air bubble through the front master cylinder window

TooMany2cvs

29,008 posts

157 months

Thursday 16th March 2017
quotequote all
A500leroy said:
Can see an air bubble through the front master cylinder window
Bleeding it is the last thing you want to do, then. The reservoir isn't part of the sealed hydraulic system - air bubbles there are irrelevant. If you draw that "bubble" in, then you'll be introducing air into the circuit, not eliminating it.

moanthebairns

19,183 posts

229 months

Friday 17th March 2017
quotequote all
http://www.ebay.co.uk/itm/like/322412808318?lpid=1...

buy this and marvel at how fking easy it is.

or

get a jam jar, tubing and a sty ball bearing working as a non-return valve, spend hours trying to fill six pot calipers with fluid, up and down, close open, pump....pump aw for fksake.....

shunter V8

788 posts

196 months

Friday 17th March 2017
quotequote all
As above buy one of these magic tools and never get stressed about bleeding brakes and clutches again,one word of advice keep the master cylinder topped up and check it constantly as it empties very quickly and you don't want air in the system or you will have to start from scratch,I did it first time I used it but after that never had a problem a cracking tool.

cbmotorsport

3,065 posts

149 months

Friday 17th March 2017
quotequote all
TooMany2cvs said:
Why do they need bleeding...?

Because you've replaced something in the hydraulics? Because you're changing the fluid? Or...?

What car? Some ABS systems can be a bit technical.
It's on a bike I would suggest.

Prof Prolapse

16,163 posts

221 months

Friday 17th March 2017
quotequote all
moanthebairns said:
http://www.ebay.co.uk/itm/like/322412808318?lpid=1...

buy this and marvel at how fking easy it is.

or

get a jam jar, tubing and a sty ball bearing working as a non-return valve, spend hours trying to fill six pot calipers with fluid, up and down, close open, pump....pump aw for fksake.....
Lol, not having a pop at your mechanical prowess MTB, but most of us use the "stty return valve" and can change all of our brake fluid, in about 20 minutes (unless you have a mental Honda ABS system).

That said I bought an "Eazi-bleed" system for about 20 quid that works well, uses the pressure from a spare tyre, and has a filled reservoir, so you just literally set the pressure and turn the caliper valve.

I did however buy it for the car. I still use the 1 way valve for the bike as I can't be bothered with the clean up.







moanthebairns

19,183 posts

229 months

Friday 17th March 2017
quotequote all
Prof Prolapse said:
moanthebairns said:
http://www.ebay.co.uk/itm/like/322412808318?lpid=1...

buy this and marvel at how fking easy it is.

or

get a jam jar, tubing and a sty ball bearing working as a non-return valve, spend hours trying to fill six pot calipers with fluid, up and down, close open, pump....pump aw for fksake.....
Lol, not having a pop at your mechanical prowess MTB, but most of us use the "stty return valve" and can change all of our brake fluid, in about 20 minutes (unless you have a mental Honda ABS system).

That said I bought an "Eazi-bleed" system for about 20 quid that works well, uses the pressure from a spare tyre, and has a filled reservoir, so you just literally set the pressure and turn the caliper valve.

I did however buy it for the car. I still use the 1 way valve for the bike as I can't be bothered with the clean up.
You have clearly never rebuilt 6 pot stty Tokico brakes. TBF, they the ball valve works well for just a flush. Useless for empty lines.

Dr Doofenshmirtz

16,952 posts

231 months

Friday 17th March 2017
quotequote all
Prof Prolapse said:
moanthebairns said:
http://www.ebay.co.uk/itm/like/322412808318?lpid=1...

buy this and marvel at how fking easy it is.

or

get a jam jar, tubing and a sty ball bearing working as a non-return valve, spend hours trying to fill six pot calipers with fluid, up and down, close open, pump....pump aw for fksake.....
Lol, not having a pop at your mechanical prowess MTB, but most of us use the "stty return valve" and can change all of our brake fluid, in about 20 minutes (unless you have a mental Honda ABS system).

That said I bought an "Eazi-bleed" system for about 20 quid that works well, uses the pressure from a spare tyre, and has a filled reservoir, so you just literally set the pressure and turn the caliper valve.

I did however buy it for the car. I still use the 1 way valve for the bike as I can't be bothered with the clean up.
I used to use the one way valve method until I bought one of these vacuum pumps linked above. The vacuum pumps are A LOT easier, quicker and less messy. For the sake of £15 don't even think about it...just get one cos they're better.
That said, on motorcycles sometimes you have to prime the system by using a syringe and pump fluid INTO the calliper and up to the reservoir to get the fluid flowing properly.

moanthebairns

19,183 posts

229 months

Friday 17th March 2017
quotequote all
Dr Doofenshmirtz said:
Prof Prolapse said:
moanthebairns said:
http://www.ebay.co.uk/itm/like/322412808318?lpid=1...

buy this and marvel at how fking easy it is.

or

get a jam jar, tubing and a sty ball bearing working as a non-return valve, spend hours trying to fill six pot calipers with fluid, up and down, close open, pump....pump aw for fksake.....
Lol, not having a pop at your mechanical prowess MTB, but most of us use the "stty return valve" and can change all of our brake fluid, in about 20 minutes (unless you have a mental Honda ABS system).

That said I bought an "Eazi-bleed" system for about 20 quid that works well, uses the pressure from a spare tyre, and has a filled reservoir, so you just literally set the pressure and turn the caliper valve.

I did however buy it for the car. I still use the 1 way valve for the bike as I can't be bothered with the clean up.
I used to use the one way valve method until I bought one of these vacuum pumps linked above. The vacuum pumps are A LOT easier, quicker and less messy. For the sake of £15 don't even think about it...just get one cos they're better.
That said, on motorcycles sometimes you have to prime the system by using a syringe and pump fluid INTO the calliper and up to the reservoir to get the fluid flowing properly.
I've seen guys with jam jars racing to get it done before their next session, stressing, coming back in with it still felling spongy.

You give them a loan of the gun, jesus, fk me thats good, i'm getting on of those.

Prof Prolapse

16,163 posts

221 months

Friday 17th March 2017
quotequote all
moanthebairns said:
You have clearly never rebuilt 6 pot stty Tokico brakes. TBF, they the ball valve works well for just a flush. Useless for empty lines.
No I've not, and I can see where you're coming from in that instance, but the OP said for changing his fluids, not for rebuilding calipers or for any particularly difficult set up.

moanthebairns

19,183 posts

229 months

Friday 17th March 2017
quotequote all
Prof Prolapse said:
moanthebairns said:
You have clearly never rebuilt 6 pot stty Tokico brakes. TBF, they the ball valve works well for just a flush. Useless for empty lines.
No I've not, and I can see where you're coming from in that instance, but the OP said for changing his fluids, not for rebuilding calipers or for any particularly difficult set up.
why spend £6 on something that is meh, when you can have the dugs baws for £15

Prof Prolapse

16,163 posts

221 months

Friday 17th March 2017
quotequote all
I guess my response is, if you're sure it's all you need why spend another tenner?

I would use the one way valve before a "fancy" set up on the CBR (I've not done the GSXR yet) because by the time I've set up the Eazi-bleed system I'd have finished changing the fluid on the old Honda.

You still have flush and clean every damned part after using it as well or it all goes cloudy, so again the stty wee valve saves time.

But yes, I agree, if you plan to rebuild calipers in the future, have a tricky system, or want to use it on a car I'd recommend spending a bit.



Dr Doofenshmirtz

16,952 posts

231 months

Friday 17th March 2017
quotequote all
You're a tough man to convince Prof biggrin

graeme4130

3,956 posts

212 months

Friday 17th March 2017
quotequote all
moanthebairns said:
Dr Doofenshmirtz said:
Prof Prolapse said:
moanthebairns said:
http://www.ebay.co.uk/itm/like/322412808318?lpid=1...

buy this and marvel at how fking easy it is.

or

get a jam jar, tubing and a sty ball bearing working as a non-return valve, spend hours trying to fill six pot calipers with fluid, up and down, close open, pump....pump aw for fksake.....
Lol, not having a pop at your mechanical prowess MTB, but most of us use the "stty return valve" and can change all of our brake fluid, in about 20 minutes (unless you have a mental Honda ABS system).

That said I bought an "Eazi-bleed" system for about 20 quid that works well, uses the pressure from a spare tyre, and has a filled reservoir, so you just literally set the pressure and turn the caliper valve.

I did however buy it for the car. I still use the 1 way valve for the bike as I can't be bothered with the clean up.
I used to use the one way valve method until I bought one of these vacuum pumps linked above. The vacuum pumps are A LOT easier, quicker and less messy. For the sake of £15 don't even think about it...just get one cos they're better.
That said, on motorcycles sometimes you have to prime the system by using a syringe and pump fluid INTO the calliper and up to the reservoir to get the fluid flowing properly.
I've seen guys with jam jars racing to get it done before their next session, stressing, coming back in with it still felling spongy.

You give them a loan of the gun, jesus, fk me thats good, i'm getting on of those.
I've got on of those vacuum pumps, and it makes a potentially messy and awkward job really easy and quick
Best £20 I've spent on tools

Prof Prolapse

16,163 posts

221 months

Friday 17th March 2017
quotequote all
Dr Doofenshmirtz said:
You're a tough man to convince Prof biggrin
Don't get me wrong it's a great tool, some jobs seem impossible without one, but I think it's horses for courses, and not everyone wants old filing cabinets filled with "used once" tools like I have!





MarkRSi

5,782 posts

249 months

Friday 17th March 2017
quotequote all
Same, will need to replace the brake fluid on my Street Triple.

moanthebairns

19,183 posts

229 months

Friday 17th March 2017
quotequote all




or prolapse method