98 Fireblade Threaded Engine Mount Hole
98 Fireblade Threaded Engine Mount Hole
Author
Discussion

Sea Demon

Original Poster:

1,170 posts

244 months

Thursday 30th March 2017
quotequote all
Engine mount hole where the crash bung would fit has threaded on my 98 Fireblade, would getting this sorted involve removing the engine? A previous owner must have done the bung up way too tight.

The hole will need to have a time-sert or helicoil fitted but the hole in the frame is lined up next to the hole that needs sorting - how much am I looking at to get this fixed?

MotorsportTom

3,343 posts

192 months

Thursday 30th March 2017
quotequote all
Struggling to picture it from your description, can you post a pick up?

If you are handy you can probably get at it from the back but it will be a PITA getting it square I expect.

If you took it as is to a garage/engineering firm I expect they won't want to do it so might be a "this is the price for not wanting to do it" type deal.

I could be wrong it might be easier than I'm thinking but if it does need to come from behind then tank, airbox, seat etc all need to be off to give you half a chance.

If you have the tools you could do it in a couple of hours and the only cost would be helicoils/helicoil kit (providing you have a drill)

gareth_r

6,793 posts

268 months

Thursday 30th March 2017
quotequote all
If you try to repair it "through" the frame you might end up with two problems.

I assume that the top engine mount is stripped? Is it possible to remove the top mounts (and whatever else needs to be taken off), loosen the rear mounts, then drop the engine enough to expose the stripped thread?

Then the only problem is keeping the re-drilled hole straight and the correct size for the thread insert. smile

Edited by gareth_r on Thursday 30th March 13:53

trickywoo

14,288 posts

261 months

Thursday 30th March 2017
quotequote all
Performance Bikes Magazine had this exact problem albeit with a later model 'blade and it was engine out.

I suspect unfortunately to do it right it will indeed be engine out.

podman

9,087 posts

271 months

Thursday 30th March 2017
quotequote all
I have known people to try eazi outs and drilling them out but if they snap, it makes life much more difficult..

Sea Demon

Original Poster:

1,170 posts

244 months

Thursday 30th March 2017
quotequote all
Cheers - I'll post a pic up later but there's nothing in the hole, just the frame in the way which I'm guessing will be a problem but at least its fixable, just a pain in the backside when its my only bike and I need it for work every day.

MotorsportTom

3,343 posts

192 months

Thursday 30th March 2017
quotequote all
Sea Demon said:
Cheers - I'll post a pic up later but there's nothing in the hole, just the frame in the way which I'm guessing will be a problem but at least its fixable, just a pain in the backside when its my only bike and I need it for work every day.
Depending on mileage I'd consider riding it.

If it were 100 miles a day I might not, but realisitcally there are 5 parts holding the engine. 1 being omitted isn't gonna change much.

Mr2Mike

20,143 posts

286 months

Thursday 30th March 2017
quotequote all
Sea Demon said:
Engine mount hole where the crash bung would fit has threaded on my 98 Fireblade,
Do you mean it's cross threaded or that the thread has stripped? "Threaded" is how it's supposed to be.

Sea Demon

Original Poster:

1,170 posts

244 months

Friday 31st March 2017
quotequote all
MotorsportTom said:
Depending on mileage I'd consider riding it.

If it were 100 miles a day I might not, but realisitcally there are 5 parts holding the engine. 1 being omitted isn't gonna change much.
I've done 2000 miles on it without it already, 100 mile round trip for the commute laugh - taking it fairly easy and not going over 8-90mph as it vibrates a fair bit.

Took it to Motorliner in Maidstone this morning, there sorting it for me. Gave me 2 options of either dropping the engine to do it or slightly enlarge the hole in the frame to it so I've gone for that option, I'm not going to sell the bike its my commuter hack and track bike - it'll be written off before its sold biggrin

Sea Demon

Original Poster:

1,170 posts

244 months

Friday 31st March 2017
quotequote all
Mr2Mike said:
Do you mean it's cross threaded or that the thread has stripped? "Threaded" is how it's supposed to be.
Sorry, thread is stripped - nothing left.

Sea Demon

Original Poster:

1,170 posts

244 months

Friday 31st March 2017
quotequote all
It rides fine really, not thrashing it or red lining it but is Ok.


Mr2Mike

20,143 posts

286 months

Saturday 1st April 2017
quotequote all
Sea Demon said:
Sorry, thread is stripped - nothing left.
Ok, that's certainly more of a problem. It's possible to install helicoils in situ by drilling out the part being clamped to the OD of the helicoil tap and then machining a top-hat sleeve to reduce it back to the original diameter. However I would personally go to fairly long lengths to avoid drilling a frame, and unless you have a lathe this isn't likely to be cost effective.

I presume the problem is the mounting at the front that goes through the 'triangle' welded onto the frame and attaches to the engine block just below the cylinder head? If so it may just be possible to remove the front mounting bolts and one of the rear mounting bolts and the exhaust mounting bolts and swing the engine down about an inch on a jack, which would be sufficient to drill, tap and helicoil the engine block. Be careful of radiator clearance etc.

Edited by Mr2Mike on Saturday 1st April 10:07

Gunk

3,302 posts

190 months

Saturday 1st April 2017
quotequote all
on my 1994 Blade the top stud was snapped so I had to drill it out. As I could get access behind the engine mounting for a nut and washer, Instead of tapping the hole I just used a longer nut and bolt with a spacer, after 12 months it's fine, I used threadlock and marked the nut with torque paint so I can keep an eye on it.