DIY Newbie - How to fit ground anchor securely
Discussion
Just bought a Mammoth Concrete-In Ground Anchor, hoping to fit it this weekend but not sure how I'm going to do it. Been reading internet forums and everyone has different opinions.
The way I intend to do it is, by removing some paving bricks, digging a hole about a cubic foot, then fill the hole with postcrete and then sink the ground anchor into it.
My only worry is, given the surrounding of the anchor is soil, is there any possibility the b
ds can pull out the anchor?
Also, people are suggesting reinforcing the concrete with metal rods to make it more secure, WTF does this mean??
After years of saving and living like a tight s
te I can finally look forward to this
:

The way I intend to do it is, by removing some paving bricks, digging a hole about a cubic foot, then fill the hole with postcrete and then sink the ground anchor into it.
My only worry is, given the surrounding of the anchor is soil, is there any possibility the b
ds can pull out the anchor? Also, people are suggesting reinforcing the concrete with metal rods to make it more secure, WTF does this mean??
After years of saving and living like a tight s
te I can finally look forward to this
: Edited by harry020 on Wednesday 5th April 08:11
Edited by harry020 on Wednesday 5th April 08:12
AS you said about digging hole is correct. Adding metal if you have any rebar like this
http://www.diy.com/departments/ffa-concept-steel-r...
see if you can put it through an gaps in the ground anchor so if someone wanted to lift the ground anchor it will not just pop up but have the rebar in the concrete and surrounding area. thus making it harder to remove the GA
http://www.diy.com/departments/ffa-concept-steel-r...
see if you can put it through an gaps in the ground anchor so if someone wanted to lift the ground anchor it will not just pop up but have the rebar in the concrete and surrounding area. thus making it harder to remove the GA
harry020 said:
given the surrounding of the anchor is soil, is there any possibility the b
ds can pull out the anchor?
Also, people are suggesting reinforcing the concrete with metal rods to make it more secure, WTF does this mean??
I think your approach sounds OK - yes, if the anchor is pulled hard enough it will give eventually, or attacked with a breaker or something like that, but it should significantly slow them down. Forum people are talking about putting something like this https://www.travisperkins.co.uk/Product/Building-M... in with the concrete. Without knowing what kind of area you live in this might be overkill or it might not. It also depends what kind of chain/padlock you intend to secure the bike to the anchor with - that might be the point of least resistance. Would recommend an alarm if there isn't one, maybe with something that pages your mobile - reduces the amount of time that they would have to work on it if it's in your garden near your bedroom or whatever. Most scrotes won't want to hang around if they can hear shouts/dogs and see lights coming on etc. Some will, in which case you will have to decide how heroic you are feeling. If you really do live in Junkyville or Bumtown perhaps consider a second anchor and chain, then it becomes a huge investment of effort and time to get the bike free with an alarm screaming and BiB hopefully on the way by then.
ds can pull out the anchor? Also, people are suggesting reinforcing the concrete with metal rods to make it more secure, WTF does this mean??
Nice looking bike by the way, 600/750/1000?
remove a few bricks then use one of these to make a hole , you can get to near 3 foot deep in no time , few bits of metal bar going sideways wouldnt hurt
http://www.ebay.co.uk/itm/Neilsen-post-hole-auger-...
http://www.ebay.co.uk/itm/Neilsen-post-hole-auger-...
Metal rods (rebar) is a good idea; once you have dug your hole, hammer them in to the ground at angles outwards from the hole leaving about 6" still into the centre where your anchor will be. Just be carefeul you don't hit drains, water pipes, gas mains etc...
Years ago I helped a mate remove his ground anchor from a monoblocked drive so he could get the drive resurfaced.
We put a scaffold pole through the ring of the anchor and used a trolley jack under one end thinking it would either crack the concrete block or snap the anchor; instead, it simply lifted the whole block of concrete out of the ground in one go.
Fair enough, if the bike had still been chained to it it would have been a lot harder to access (and bloody unwieldy to move!), but we were both surprised how easily it was done.
Years ago I helped a mate remove his ground anchor from a monoblocked drive so he could get the drive resurfaced.
We put a scaffold pole through the ring of the anchor and used a trolley jack under one end thinking it would either crack the concrete block or snap the anchor; instead, it simply lifted the whole block of concrete out of the ground in one go.
Fair enough, if the bike had still been chained to it it would have been a lot harder to access (and bloody unwieldy to move!), but we were both surprised how easily it was done.
I'm not an expert, and without wishing to be overly critical, it's difficult to see the advantages of setting this type of anchor in concrete over something much simpler like those which use resin anchoring bolts. Your anchor is chunky but still exposed and therefore an easy target for an angle grinder. Setting in concrete makes a lot more sense for hollow "Y-shaped" anchors. They don't leave anything exposed, can be secured more easily with reinforcements over the "Y" shape, and also can be ridden over to save space when not in use.
I don't think 1sqft is enough, you could just get a crowbar in there, pop it out and carry it, I did a square metre for my Y-shaped anchor, but do a compromise based on some basic maths to make sure you have enough aggregate etc. 1m^2 is a fair amount of materials, and mixing, by hand.
If you're digging into existing concrete surface, it's worth trying to make the cavity narrower at the top (think a vase shape) to make it more difficult to pull out
if you don't reinforce, it can be shattered much more easily with a hammer. Reinforcing is simple however, you just cut up some rebar (or even scrap metal), and bend it into a frame, then pour your mixture over it. Also try wedging some bars over the anchor into the surroundings to make it more difficult to pull out.
You have to take care not to use too much water in the concrete mixture as well, otherwise it is easier to break up with a hammer.
It's actually much easier than I make it sound.
I don't think 1sqft is enough, you could just get a crowbar in there, pop it out and carry it, I did a square metre for my Y-shaped anchor, but do a compromise based on some basic maths to make sure you have enough aggregate etc. 1m^2 is a fair amount of materials, and mixing, by hand.
If you're digging into existing concrete surface, it's worth trying to make the cavity narrower at the top (think a vase shape) to make it more difficult to pull out
if you don't reinforce, it can be shattered much more easily with a hammer. Reinforcing is simple however, you just cut up some rebar (or even scrap metal), and bend it into a frame, then pour your mixture over it. Also try wedging some bars over the anchor into the surroundings to make it more difficult to pull out.
You have to take care not to use too much water in the concrete mixture as well, otherwise it is easier to break up with a hammer.
It's actually much easier than I make it sound.
As has been said, don't worry too much. The anchor is a deterrent only. The chain/padlock will always be the weakest point, and they'll angle grind that off without touching the anchor. They don't even care about noise anymore. Sad but true.
Security is a multi layered thing. Use a number of devices to make your bike less easy to steal than the one down the road.
Security is a multi layered thing. Use a number of devices to make your bike less easy to steal than the one down the road.
harry020 said:
Thanks for the answer RemaL. For a hole the size of a cubic foot how many rebar bars would you suggest?
i've not had to do this myself but anything to make it harder to pull. but like others said once done it's the chain and lock that's the wewak point so don't scrimp on them Gassing Station | Biker Banter | Top of Page | What's New | My Stuff


