848 Evo Map for termi slip-ons?
848 Evo Map for termi slip-ons?
Author
Discussion

DuncsGTi

Original Poster:

1,185 posts

210 months

Thursday 13th April 2017
quotequote all
I've been looking at carbon Termi slip-ons for my 2012 848 Evo and I'm hoping the collective knowledge of BB can help me out.

The cans are about £7-800 from various suppliers around the EU.

I assume the bike will then need mapped to take advantage of the increased flow and to ensure the afr stays within tolerances.

Can the standard ECU be flashed with a new map or will I need to buy the Ducati performance one (about £300 on Ebay)?

Is there any alternative to do the same for less money? (power commander??)

I'm not after any more power but I'd like the reassurance that I'm not risking grenading my engine by running it lean.

I'm a complete novice at all this sort of stuff so any guidance would be appreciated thumbup


trickywoo

14,288 posts

261 months

Thursday 13th April 2017
quotequote all
Normally just a can won't need a remap. It might benefit from one but it shouldn't be necesssry from a safety point of view.

If it was me I'd either get a power commander v with self mapping or have a power run on a dyno to see where your afr is and go from there.

DuncsGTi

Original Poster:

1,185 posts

210 months

Thursday 13th April 2017
quotequote all
trickywoo said:
Normally just a can won't need a remap. It might benefit from one but it shouldn't be necesssry from a safety point of view.

If it was me I'd either get a power commander v with self mapping or have a power run on a dyno to see where your afr is and go from there.
I wasn't sure whether it would actually need a map but I figure (perhaps wrongly) that removing the standard cans with cats and fitting free flowing replacements without, will significantly increase gas flow rate and lean up the mixture.

I'll look at the PC V, are there any alternatives out there?





Steve Bass

10,758 posts

264 months

Friday 14th April 2017
quotequote all
DuncsGTi said:
I wasn't sure whether it would actually need a map but I figure (perhaps wrongly) that removing the standard cans with cats and fitting free flowing replacements without, will significantly increase gas flow rate and lean up the mixture.

I'll look at the PC V, are there any alternatives out there?
Ducati performance maps are ropey at best. Get either a PCV or Rapid Bike module and have the bike set up properly. You'll be amazed at the changes







Edited by Steve Bass on Friday 14th April 03:52

rodericb

8,957 posts

157 months

Friday 14th April 2017
quotequote all
You can get the standard ECU flashed with a map to suit. Send off the ECU, gets flashed and sent back to you. You can also get software to do the job yourself, one such like that is Tuneboy. There are some other 'enthusiast' level software apps out there which are cheaper than Tuneboy.

If you do get software to do it yourself you might find a map on the internet, otherwise it'll be dyno time. You might like to have a read of the Sigma Performance guide on fuel injection and have a read of the Nemesis or Microtec manuals. The theory of it is reasonably simple amd it's good to arm yourself with a bit of knowledge so you can make the right decision for yourself.

http://www.sigmaperformance.com/weber.html

Edited by rodericb on Friday 14th April 02:05

3DP

9,991 posts

265 months

Friday 14th April 2017
quotequote all
The cats are in the end cans, so a re-map would be advised as you are de-catting as well as putting on free flowing exhausts. Ducati ECUs are re-flashable (although I've heard some 848 ones are not). A DP ECU would be a minimum (or re-flash to DP map). I would join and ask/search on the Ducatiforum.co.uk for specific advice as there is a very finite pool of people on here with 848/1098/1198. I don't see the point in buying a PC V when the existing ECU can be live tweaked/flashed by Ducati tuners on the dyno.

If you want to save money, you can get slash cut Termis for as little as £650 from Italy on Ebay and you can get use Tuneboy hardware and software to reflash your existing ECU if you computer literate, for about £30. I've just bought slash cuts from sestamarcia-racing-parts and the service was superb.

I bought a second hand DP ECU for my 1098 for £90 off a Ducati forum, so I'll be seeing how that is with the Termis then getting it mapped/flashed by a Ducati specialist if it doesn't feel spot on. The OEM ECU is then preserved.

DuncsGTi

Original Poster:

1,185 posts

210 months

Friday 14th April 2017
quotequote all
Steve Bass said:
DuncsGTi said:
I wasn't sure whether it would actually need a map but I figure (perhaps wrongly) that removing the standard cans with cats and fitting free flowing replacements without, will significantly increase gas flow rate and lean up the mixture.

I'll look at the PC V, are there any alternatives out there?
Ducati performance maps are ropey at best. Get either a PCV or Rapid Bike module and have the bike set up properly. You'll be amazed at the changes
rodericb said:
You can get the standard ECU flashed with a map to suit. Send off the ECU, gets flashed and sent back to you. You can also get software to do the job yourself, one such like that is Tuneboy. There are some other 'enthusiast' level software apps out there which are cheaper than Tuneboy.

If you do get software to do it yourself you might find a map on the internet, otherwise it'll be dyno time. You might like to have a read of the Sigma Performance guide on fuel injection and have a read of the Nemesis or Microtec manuals. The theory of it is reasonably simple amd it's good to arm yourself with a bit of knowledge so you can make the right decision for yourself.

http://www.sigmaperformance.com/weber.html

Edited by rodericb on Friday 14th April 02:05
3DP said:
The cats are in the end cans, so a re-map would be advised as you are de-catting as well as putting on free flowing exhausts. Ducati ECUs are re-flashable (although I've heard some 848 ones are not). A DP ECU would be a minimum (or re-flash to DP map). I would join and ask/search on the Ducatiforum.co.uk for specific advice as there is a very finite pool of people on here with 848/1098/1198. I don't see the point in buying a PC V when the existing ECU can be live tweaked/flashed by Ducati tuners on the dyno.

If you want to save money, you can get slash cut Termis for as little as £650 from Italy on Ebay and you can get use Tuneboy hardware and software to reflash your existing ECU if you computer literate, for about £30. I've just bought slash cuts from sestamarcia-racing-parts and the service was superb.

I bought a second hand DP ECU for my 1098 for £90 off a Ducati forum, so I'll be seeing how that is with the Termis then getting it mapped/flashed by a Ducati specialist if it doesn't feel spot on. The OEM ECU is then preserved.
All great info, thanks thumbup

I was originally happy with the sound from the standard cans until my mate started his 916 with Termis cloud9