Check your bellypan bolts!
Discussion
I recently had the misfortune of visiting a certain middlesex dyno / bike / scooter place with the 748SP and it came back with a great hole in the bellypan. Fortunately a chinese fairing not the beautiful pristine original that's tucked up safe.
It looked like a dzus was caught when rolling it backwards. Anyway they did the right thing and fixed it up for me after I made a small fuss, but I noticed they'd elected to only put one dzus in there. I confess I didn't do the right thing and remove / refit to check it was all ok.
Fast forward to yesterday's first trackday of the year -- end of straight flat out and a massive flash of yellow as both fairing lowers including bellypan ripped right off in the wind leaving the four upper frame fixings dzused intact with bits of fairing left. Basically it's written off the fairing including headlight part where it's ripped the holes out.
So moral of story (apart from being particular about where you take your bike) is watch out for that bellypan -- 150mph wind will get inside!
Thankfully nobody hurt/damaged.
It looked like a dzus was caught when rolling it backwards. Anyway they did the right thing and fixed it up for me after I made a small fuss, but I noticed they'd elected to only put one dzus in there. I confess I didn't do the right thing and remove / refit to check it was all ok.
Fast forward to yesterday's first trackday of the year -- end of straight flat out and a massive flash of yellow as both fairing lowers including bellypan ripped right off in the wind leaving the four upper frame fixings dzused intact with bits of fairing left. Basically it's written off the fairing including headlight part where it's ripped the holes out.
So moral of story (apart from being particular about where you take your bike) is watch out for that bellypan -- 150mph wind will get inside!
Thankfully nobody hurt/damaged.
It's a shame but you really should give your bike the once over after someone else works on it.
My worse one was the mechanic not mounting the rear calliper properly after refitting the rear wheel.
Caliper spun and locked the rear wheel when the hose was trapped between the spindle and swing arm.
My worse one was the mechanic not mounting the rear calliper properly after refitting the rear wheel.
Caliper spun and locked the rear wheel when the hose was trapped between the spindle and swing arm.
Having seen this happen on the road many years ago with a friend riding his 888, which ended up with him riding over his own lower fairing and nearly having him off, I check these periodically, the recently Firestorm shook 3 bolts out in a couple of hundred miles so both that and the LC have nylocks securing the bolts as well.
Unfortunately, as you have found, professionals do get it wrong too frequently, ignore reputations to a point & trust no one until proven is a good starting point.
Unfortunately, as you have found, professionals do get it wrong too frequently, ignore reputations to a point & trust no one until proven is a good starting point.
When I lived in Norfolk, CJ Ball at Hales/Norwich were the place -- specifically a bloke called Coddy we raced together and he was hyper meticulous. Although I still use them from the new bike even though it's a 150 mile ride each way I chanced this local place for the simple dyno run.
When you find a good mechanic you can trust they're really worth holding on to.
When you find a good mechanic you can trust they're really worth holding on to.
I hadn't much experience of this until I got my newer bike. I did most of my stuff myself until then.
Asked for heated grips to be fitted, and the sales bloke said he'd have the detailer tidy the downpipes. They did a great job of both, apart from when the bar end fell off and nearly hit a mate behind me. After this I noticed a few more fairing fixtures were missing.
I returned it to them (quite fairly, they wanted to check themselves), and they allegedly checked it over. Then a crash bung fell off somewhere in the borders. Which again they reimbursed after a grumpy email from me. I declined letting them touch it again.
I have since changed garage, but now paranoia means I spent ten minutes last week checking someone elses work after paying someone to service it. The new garage is so far so good however.
Just one of those things I guess. I think a small amount of mechanical gumption and personal responsibility is still a prerequisite of running a motorcycle. So no hard feelings.
Asked for heated grips to be fitted, and the sales bloke said he'd have the detailer tidy the downpipes. They did a great job of both, apart from when the bar end fell off and nearly hit a mate behind me. After this I noticed a few more fairing fixtures were missing.
I returned it to them (quite fairly, they wanted to check themselves), and they allegedly checked it over. Then a crash bung fell off somewhere in the borders. Which again they reimbursed after a grumpy email from me. I declined letting them touch it again.
I have since changed garage, but now paranoia means I spent ten minutes last week checking someone elses work after paying someone to service it. The new garage is so far so good however.
Just one of those things I guess. I think a small amount of mechanical gumption and personal responsibility is still a prerequisite of running a motorcycle. So no hard feelings.
I got a garage to fit goodbridge braided hoses to my bike when it was in for a service. I was going to order them but he said its fine ill get them. Having never touched a bike I flung it in, paid a high fee, then out on a run 50 miles from home noticed I had little to nil brake fluid. It had pished all over my calipers and pads at the banjo.
I took it back, and it took a week to fix, amongst other things. It still wasn't done right. I physically went down and saw the mechanic struggle with the lines, bleeding them into an irn bru bottle and he asked why I never bought goodridge or hel instead of these Chinese brands. The b
d owner had charged me goodridge prices and bought cheap s
t.
He f
ked a set of pads with the fluid, telling me he's cleaned and treated them, they don't need replacing. I picked up the bike in the wet and flew right out at the first T-juction due to not being able to stop. He argued and spat the dummy that this was now costing him a set of pads, he replaced my ebcs with gold s
t.
It took about 3 weeks for the proper lines to get fitted and I have damage to the fork leg from the brake fluid... That told me to try to never use a mechanic again. Sadly sometimes I still do. But you always end up checking it as best as you can.
I took it back, and it took a week to fix, amongst other things. It still wasn't done right. I physically went down and saw the mechanic struggle with the lines, bleeding them into an irn bru bottle and he asked why I never bought goodridge or hel instead of these Chinese brands. The b
d owner had charged me goodridge prices and bought cheap s
t.He f
ked a set of pads with the fluid, telling me he's cleaned and treated them, they don't need replacing. I picked up the bike in the wet and flew right out at the first T-juction due to not being able to stop. He argued and spat the dummy that this was now costing him a set of pads, he replaced my ebcs with gold s
t. It took about 3 weeks for the proper lines to get fitted and I have damage to the fork leg from the brake fluid... That told me to try to never use a mechanic again. Sadly sometimes I still do. But you always end up checking it as best as you can.
catso said:
Prof Prolapse said:
Answer me this MTB, did you use a main dealer?
Or did you use the cheapest bloke you could find?
Irn Bru bottle indeed, what next a deep fried Mars bar?... Or did you use the cheapest bloke you could find?

He promised he had a workshop next door and full time mechanic, wasnt till i saw it, some fat b
d with a halfords socket set and a stand. Regarding the dzus -- yes tape a good idea but they are adjustable and can be made good and tight.
The bike without the "repair" spent a day around Spa last year and according to the previous owner, many a trackday throughout its life and there was never a problem.
I'm quite clear it was the dealer that hadn't done it right, but what you say about tape is something I'll definitely do in future thanks.
The bike without the "repair" spent a day around Spa last year and according to the previous owner, many a trackday throughout its life and there was never a problem.
I'm quite clear it was the dealer that hadn't done it right, but what you say about tape is something I'll definitely do in future thanks.
dzus or any type of fastener you can add an extra plastic washer to the bolt or you can cut an old inner tube into 10mm squares, fold them and cut a tiny bit out of the folded bit so that when you open it up you have a small hole in the middle, that does stop them vibrating loose as does the tape over the top.
Also make sure you have the right length and type of bolts for the fasteners.
Also make sure you have the right length and type of bolts for the fasteners.
Gassing Station | Biker Banter | Top of Page | What's New | My Stuff





