Trying to start bike after 3-4 years. Carb blocked?
Discussion
Anyone had any positive experiences cleaning a carb that's been sat full of fuel for years?
I've not started this KTM 625SMC for three or four years. Now I'm trying to, after fitting a new battery and draining-refilling with fresh fuel, but looks like there's no fuel getting through the carb.
I took the carb off and it's all a nasty black colour inside and generally looks filthy. I've removed the jets and made sure they were clear (already seemed OKish, and carefully cleaned up the obvious crap a little. I haven't touched the accelerator pump thing because I had a bad experience the only other time I messed with one of those, donkey's years ago.
I bunged the carb back on and hoped the above would be enough to at least get the engine started - but obviously not.
I've been searching the net but mostly I've found guys talking about products we don't get over here, or using chemicals I've not heard of or know where to get.
Other options...
Cheers
I've not started this KTM 625SMC for three or four years. Now I'm trying to, after fitting a new battery and draining-refilling with fresh fuel, but looks like there's no fuel getting through the carb.
I took the carb off and it's all a nasty black colour inside and generally looks filthy. I've removed the jets and made sure they were clear (already seemed OKish, and carefully cleaned up the obvious crap a little. I haven't touched the accelerator pump thing because I had a bad experience the only other time I messed with one of those, donkey's years ago.
I bunged the carb back on and hoped the above would be enough to at least get the engine started - but obviously not.
I've been searching the net but mostly I've found guys talking about products we don't get over here, or using chemicals I've not heard of or know where to get.
Other options...
- Ultrasonic cleaning; Local bike shop guy said he could send it for ultrasonic cleaning for ~£60 if I take the carb in. No guarantees it'll work, of course.
- Second-hand carb from eBay. Seems quite pricey at ~£270 though.
Cheers
cmaguire said:
Where are you? I presume single carb on that.
There must be someone with an ultrasonic cleaner on here close to you. For free it's a no-brainer.
I'm Ely way, I'd chuck it in mine for free.
I'm way down in Hampshire mate, 10 miles outside Portsmouth. Yeah it's only a simgle carb. There must be someone with an ultrasonic cleaner on here close to you. For free it's a no-brainer.
I'm Ely way, I'd chuck it in mine for free.
OK, £30 for a watch one..
https://www.banggood.com/BK-3550-35W50W-220V-High-...
https://www.banggood.com/0_8L-35W-42kHz-Digital-Ul...
£50 for something a bit bigger
https://www.banggood.com/BK-3550-35W50W-220V-High-...
https://www.banggood.com/0_8L-35W-42kHz-Digital-Ul...
£50 for something a bit bigger
cmaguire said:
As far as ultrasonic cleaners go, it'll need to be at least 2litres to get his carb submerged properly and anything without a heater should go straight in the bin. The solution wants to be hot to clean properly.
I'm just doing research into ultrasonic cleaners now and it it seems you are quite right. podman said:
Defo go down the ultrasonic route first, £60 is £20 more than I paid for a pair of carbs...
Make sure whoever does them, strips them down completely before cleaning as just dunking the whole thing in intact wont give you a good result...
How completely are we talking about though? Just taking the bowl off and jets out is ok. Anything more like splitting the body of the carb looks likely to end in disaster. Make sure whoever does them, strips them down completely before cleaning as just dunking the whole thing in intact wont give you a good result...
4737 Carlin said:
How completely are we talking about though? Just taking the bowl off and jets out is ok. Anything more like splitting the body of the carb looks likely to end in disaster.
That's what I would do. Float bowl off, jets/needles and floats removed. And then put the whole lot in at 50 degrees for 45 mins. Go from there, more time, more heat etc It's only the bowl area that will be the problemI would take the slide out too dependent on what carb it was if fully submerging it. I've done this a few times with carbs, the emulsion tube and pilot are the biggest risk for blockages
Edited by cmaguire on Thursday 18th May 20:33
cmaguire said:
Float bowl off, jets/needles and floats removed. And then put the whole lot in at 50 degrees for 45 mins. Go from there, more time, more heat etc It's only the bowl area that will be the problem
I would take the slide out too dependent on what carb it was if fully submerging it. I've done this a few times with carbs, the emulsion tube and pilot are the biggest risk for blockages
Cheers. I think that's they way I'll proceed. I would take the slide out too dependent on what carb it was if fully submerging it. I've done this a few times with carbs, the emulsion tube and pilot are the biggest risk for blockages
Apologies for stating the obvious but have you tried a new spark plug, or is the current spark plug wet from trying to start it, and I assume you know not to touch the throttle when you turn it over?
Also does the accelerator pump actually work, a couple of twists on the throttle should throw enough fuel into the cylinder to at least get a cough out of it even it it does not catch?
Other things to check;
- Carb boot going into the head, they go hard and crack letting in air
- Auto valve lifter stuck open, this works off the left exhaust valve holding it open when the engine is turned over slowly. Try a few hard prods on the kickstart (make sure the stand is up to give you full travel) and check you actually have some compression. They are actually very easy to start on the kickstart should you ever need to use it.
Another tip, once you do get it running don't leave it ticking over on the side stand because the valve train is just splash fed from the timing chain, it is a crap design and if you run the engine at an angle the cam bearing gets starved of oil along with the valve roller bearings.
Also does the accelerator pump actually work, a couple of twists on the throttle should throw enough fuel into the cylinder to at least get a cough out of it even it it does not catch?
Other things to check;
- Carb boot going into the head, they go hard and crack letting in air
- Auto valve lifter stuck open, this works off the left exhaust valve holding it open when the engine is turned over slowly. Try a few hard prods on the kickstart (make sure the stand is up to give you full travel) and check you actually have some compression. They are actually very easy to start on the kickstart should you ever need to use it.
Another tip, once you do get it running don't leave it ticking over on the side stand because the valve train is just splash fed from the timing chain, it is a crap design and if you run the engine at an angle the cam bearing gets starved of oil along with the valve roller bearings.
Gassing Station | Biker Banter | Top of Page | What's New | My Stuff


