Wrong chain fitted?
Author
Discussion

Codswallop

Original Poster:

5,260 posts

225 months

Friday 19th May 2017
quotequote all
Had a replacement chain and sprockets fitted to my bike the other day by a dealer. On the ride home, there was a lot of chain noise and a bit of bounce as though the chain was too tight.

Got home, and there was about 25mm play (recommended 35mm). Trouble is, the adjuster looks like this:





As you can see, the rear nut is hanging off and I can't slacken the chain any further. Is this acceptable? Do I need to go back and get them to fit a longer chain?

DuraAce

4,272 posts

191 months

Friday 19th May 2017
quotequote all
Have they fitted the correct size sprockets?

I'd be counting the number of teeth (front and rear sprockets) and then the number of links in the chain and compare that against the standard spec for your bike.

You'd be better off fixing it yourself as it doesn't look like they've done much of a job for you!

Jazoli

9,707 posts

281 months

Friday 19th May 2017
quotequote all
That is piss poor to be honest, that locknut on the adjuster is a pisstake, its pretty obvious the chain is too short if the sprocket sizes are correct, I'd be back to them and get them to sort it out.

CoolHands

23,722 posts

226 months

Friday 19th May 2017
quotequote all
Hahaha thank god I never pay anyone to work on my vehicles.

Gunk

3,302 posts

190 months

Friday 19th May 2017
quotequote all
CoolHands said:
Hahaha thank god I never pay anyone to work on my vehicles.
Same here, I do all my own maintenance, it's not hard to do a better job than most of the doughnuts out there.

pozi

1,725 posts

218 months

Friday 19th May 2017
quotequote all
That is a piss poor effort by the dealer, it is a shame PH has the no name and shame rule because that is a dealer to avoid.

Biker's Nemesis

41,487 posts

239 months

Friday 19th May 2017
quotequote all
If they have fitted aftermarket sprockets the front one will not have a rubber damper fitted which causes more noise than a standard fitment one.

Cheap chain and sprockets never ever work out.

I'd take it back also, it's not a hard job tofurkey chain and sprockets correctly.

Rubin215

4,201 posts

187 months

Friday 19th May 2017
quotequote all
Did they supply the chain and sprockets or did you buy them off t'internet and pay the dealer to fit them?

If they supplied then I would be going back...

Gavia

7,627 posts

122 months

Saturday 20th May 2017
quotequote all
Wheelie machine. Nail it everywhere and the front will be lifting for fun.

Jazoli

9,707 posts

281 months

Saturday 20th May 2017
quotequote all
Gavia said:
Wheelie machine. Nail it everywhere and the front will be lifting for fun.
Someone has been on the shandy......

EagleMoto4-2

669 posts

135 months

Saturday 20th May 2017
quotequote all
Check the number stamped on the front and rear sprockets and make sure they have correct number of teeth. They may have just fitted a chain with not enough links.
New chains do make a noise though. Recently fitted a new DID X-ring chain with some JT sprockets to one of my bikes, and there is a whine between 40-70mph, correct slack and lubed too.

mak

1,445 posts

257 months

Saturday 20th May 2017
quotequote all
They have cut the chain to short, the new chain would have been to long, I dread to think how they actually managed to get the joining link in place with it that tight redface . Bodging s.

Biker 1

8,615 posts

150 months

Sunday 21st May 2017
quotequote all
Looks like a total bodge. Surely even the most junior technician would have spotted that one??
OP: didn't you give the work even a cursory inspection before riding off? I'm no mechanic, but its pretty obvious that the chain adjusters are miles out.

Gunk

3,302 posts

190 months

Sunday 21st May 2017
quotequote all
EagleMoto4-2 said:
Check the number stamped on the front and rear sprockets and make sure they have correct number of teeth. They may have just fitted a chain with not enough links.
New chains do make a noise though. Recently fitted a new DID X-ring chain with some JT sprockets to one of my bikes, and there is a whine between 40-70mph, correct slack and lubed too.
On a 600 Hornet front should be 15T rear 45T