Anyone tried to repair cracks in carbon fiber?
Anyone tried to repair cracks in carbon fiber?
Author
Discussion

robbocop33

Original Poster:

1,207 posts

138 months

Wednesday 31st May 2017
quotequote all
Zxr750 i just bought has a real carbon fibre front mudguard and hugger. The front mudguard has a couple of cracks in it at the leading edge, looks cack!
At these cracks the resin finish is cracked and flaking off, none of the carbon tweel underneath is missing.
Is it just a case of sanding the damaged parts and then the whole thing and covering in new resin? Thanks.

jackh707

2,132 posts

187 months

Wednesday 31st May 2017
quotequote all
pictures would help.

YOU can't repair cracks in the actual carbon, if its just the epoxy finish you could epoxy over the top and sand down however i reckon you'll struggle to get the desired finish.

You can "patch repair' carbon fibre but i don't think that would help you either and its probably not applicable.

also its twill biggrin

robbocop33

Original Poster:

1,207 posts

138 months

Wednesday 31st May 2017
quotequote all
Here's some pics. Tried to upload three pics, not showing? Click on pic you'll see the rest.



Edited by robbocop33 on Wednesday 31st May 20:46

Gavia

7,627 posts

122 months

Wednesday 31st May 2017
quotequote all
robbocop33 said:
Here's some pics. Tried to upload three pics, not showing? Click on pic you'll see the rest.



Edited by robbocop33 on Wednesday 31st May 20:46
Technically speaking. That's fked.

Mr OCD

6,388 posts

242 months

Wednesday 31st May 2017
quotequote all
Gavia said:
Technically speaking. That's fked.
Speaking technically? You?

Funny biggrin

robbocop33

Original Poster:

1,207 posts

138 months

Wednesday 31st May 2017
quotequote all
Gavia said:
Technically speaking. That's fked.
Kind of thought that. Seen carbon repair kits all over ebay so just wondered if it was possible.

Biker's Nemesis

41,487 posts

239 months

Gary C

15,376 posts

210 months

Wednesday 31st May 2017
quotequote all
Done quite a few repairs of carbon Kevlar weave and it's really difficult to restore any sort of structural integrity as you can't really get the new expoy to be absorbed by the weave. If it's not structural, then a bit of gel coat can be slapped on and polished, but I've never had much luck with that (but on a competition canoe you don't really try)

robbocop33

Original Poster:

1,207 posts

138 months

Thursday 1st June 2017
quotequote all
If it was structural i wouldn't even have posted here. I'm going to have a go anyway just as an experiment and i'll post the hilarious results! ;-)

jackh707

2,132 posts

187 months

Thursday 1st June 2017
quotequote all
Yeah have a go at repairing that.

Sand it down Wack a small patch over, epoxy, let it cure.
Sand it down again, then epoxy finish.

It's still perfectly functional as fender/guard.

hman

7,497 posts

225 months

Thursday 1st June 2017
quotequote all
I'd be tempeted to repair it then if it looks gash - paint it, it will still be carbon fibre so lightweight and strong..

upsidedownmark

2,120 posts

166 months

Thursday 1st June 2017
quotequote all
Carbon in that is purely for show.. you're looking at a cosmetic repair.

I'd sand back the top layer, fill the cracks with epoxy - put some tape on the back and fill it a coat at a time - would help if you could thicken with something like colloidal silica..
Then gloss coat / laquer the top - could paint on raw epoxy, but probably difficult to get a good finish, rattle can of laquer / clearcoat might be a better option.

Gary C

15,376 posts

210 months

Thursday 1st June 2017
quotequote all
robbocop33 said:
If it was structural i wouldn't even have posted here. I'm going to have a go anyway just as an experiment and i'll post the hilarious results! ;-)
Doh, didnt mean structural as in chassis, but if it carries any sort of load, be it even just wind pressure. I

f you just butter it up with gel coat it might hold together, but unlike a piece of trim, if it has any sort of reasonable pressure then it may just crack again.

But, you might as well try smile

VonSenger

2,465 posts

220 months

Friday 2nd June 2017
quotequote all
Bin it, then look out on ebay for another one. Not sure how much your time is worth to you, but Id not bother as life is to short to piss around with hours of sanding etc.

Cadaver

32 posts

114 months

Friday 2nd June 2017
quotequote all
do a fibreglass patch on the back side, only a layer or two and then epoxy resin on the front side. Flat it back and get the whole part re lacquered. won't be perfect, but would be an improvement.

Treehead3000

97 posts

144 months

Wednesday 7th June 2017
quotequote all
Give this a whirl if you haven't already repaired it.

https://www.youtube.com/watch?v=A6G_L6FGnsQ

Good Luck!

Composite Guru

2,527 posts

234 months

Wednesday 7th June 2017
quotequote all
Cadaver said:
do a fibreglass patch on the back side, only a layer or two and then epoxy resin on the front side. Flat it back and get the whole part re lacquered. won't be perfect, but would be an improvement.
Exactly what I would do. If you do it from the underside you wont see it. Might be worth getting something to pigment the epoxy too so it doesn't turn white when it cures.