Remapping options... Dynojet?
Remapping options... Dynojet?
Author
Discussion

Prof Prolapse

Original Poster:

16,163 posts

221 months

Wednesday 21st June 2017
quotequote all
Well my GSXR has developed a flat spot since I was forced to pull the cables out of the stty fking exhaust valve at an unknown location somewhere in the Highlands.

But I don't know how anybody could possibly live with the resultant fuelling. It became rideable, but third gear is horrendous from 5000-7000rpm, and there's additional flat spots including one at 140mph in fourth which nearly resulted in a change of undercrackers. If you're flat out (but not too fast) it's probably tolerable, but I'm a little baffled how anyone just disconnects the valve and lives with it. I'm currently making sure everything is running OK and I've not accidentally masked a real problem.

So presumably I need to have it remapped, but what are my options?

Dynojet PCV seems to be the most common choice, they also fit it locally, and it allows the fitment of a budget quickshifter which may be fun I guess. But is there anything else I should be considering?

Bike is 2013 (too fking new to have this problem frankly), standard exhaust beyond the SET removal, and only currently used on the road but this may change in the future, no desire to modify anything.

Cheers,
PP





Jazoli

9,707 posts

281 months

Wednesday 21st June 2017
quotequote all
I think you can have have the ecu 'flashed' on your bike, which as you probably know means writing a new map direct to the ECU rather than using a piggyback ecu like a PCV, which means all you pay for is dyno time.

A local guy to me uses the Woolich stuff with great results

https://en-gb.facebook.com/Junction-33-Dyno-Centre...

The you can just buy a Healtech QS and plug and play, Dynojet QS's are pants.

rat840771

2,028 posts

196 months

Wednesday 21st June 2017
quotequote all
I second Woolich, but it must be in the hands of someone who's knows what they are doing.

BSD are very good, but at £400 its not cheap, they removed all of the cables for exhaust valve.

They can even program the QS kill times for each gear through the ECU.


trickywoo

14,283 posts

261 months

Wednesday 21st June 2017
quotequote all
Jazoli said:
The you can just buy a Healtech QS and plug and play, Dynojet QS's are pants.
Second that. I've got the Healtech QS on a K4 750 and its been great.

Mr OCD

6,388 posts

242 months

Wednesday 21st June 2017
quotequote all
Woolich ECU flash is the way to go these days...

For fine tuning you can either:

- have the base map (woolich) fine tuned via custom tuning on the dyno

OR

- have the base map (woolich) and use a Dynojet power commander to do the fine tuning (plus can run two maps) (this is usually the cheaper option)

I'd only go the dynojet route if already have the power commander.

Prof Prolapse

Original Poster:

16,163 posts

221 months

Wednesday 21st June 2017
quotequote all
Thanks all. I'll have a look at just getting it flashed once I've made sure it's running spot on.

Jazoli said:
A local guy to me uses the Woolich stuff with great results

https://en-gb.facebook.com/Junction-33-Dyno-Centre...
Jazoli, have you used this chap before? It's a bit of a trek, but a good recommendation goes a long way... Cheers.

Also I think i'll leave the QS for now (skint and kids birthday next week), but the brand you say is the one I'd go for.


Edited by Prof Prolapse on Wednesday 21st June 12:00

podman

9,086 posts

271 months

Wednesday 21st June 2017
quotequote all
maybe nearer or not but my friend had his 2008 GSXR750 sorted after removing the SET valve by Dave Wood Racing, in Aylesbury, I bought my GSXR1000 from him , he knows his stuff.

https://www.davewoodracing.com/ecu-tuning/

I have also had work done by BSDs and rate him highly as well but it seems you could take your pick from any of the suggestions made.

robinh73

1,350 posts

231 months

Wednesday 21st June 2017
quotequote all
I have got the full Woolwich package on my GSXR600 race bike. It is a great bit of kit and includes launch control and pit lane speed limiter. I run the Woolwich quickshifter also, which works well. The only downside with Woolwich is the support. The kit works well, but the support is a bit lacking. If you want to run a quickshifter, I would strongly recommend an HM. I have had a huge amount of work done on my bike my MSG Racing in Aylesbury. They specialise in Suzukis and have removed part of the Woolwich fuel side of things in favour of Bazzaz. It seems to work well so far and has got great figures on the dyno.

Jazoli

9,707 posts

281 months

Wednesday 21st June 2017
quotequote all
Prof Prolapse said:
Jazoli, have you used this chap before? It's a bit of a trek, but a good recommendation goes a long way... Cheers.

Also I think i'll leave the QS for now (skint and kids birthday next week), but the brand you say is the one I'd go for.
He sorted out my Exup many years ago when it was all jets and needles, I can't comment on his mapping skills but he has a very good reputation locally and has been in business a long time. smile

Prof Prolapse

Original Poster:

16,163 posts

221 months

Wednesday 21st June 2017
quotequote all
Cheer mate

podman

9,086 posts

271 months

Wednesday 21st June 2017
quotequote all
Just spotted your up in Scotland...Must be someone (a lot) nearer who can do this for you.

cmaguire

3,589 posts

140 months

Wednesday 21st June 2017
quotequote all
You cant just disconnect the cables. The spring on it is set to keep it open by default but what you describe sounds like the pressure of the exhaust gas may be trying to close it dependent on revs/gear/throttle/backpressure etc.
If they are disabled on a mapped bike like mine then the cables are still connected to ensure it can't move, the servo motor is just switched off in the ecu.

I just picked up a new GSXR1000 and I'd forgotten how absolutely bks all these fuel injected newer bikes run as standard. Surging on a constant throttle, that stupid exhaust valve opening and shutting altering the engine braking and the acceleration. Until you get over 5000rpm on it rides crap.
No doubt I'll be begrudgingly voiding my warranty with a remap to get it running right once all the emissions/noise crap is removed

cmaguire

3,589 posts

140 months

Wednesday 21st June 2017
quotequote all
And a remap (done by someone that actually knows what they are doing) is way better than any fuelling module because with them you still have all the emissions and noise crap.

Prof Prolapse

Original Poster:

16,163 posts

221 months

Monday 3rd July 2017
quotequote all
Right just to close this off as few had shown interest and anyone who has similar issue probably would benefit from knowing what happened. Before I concluded it was the SET valve and remap I obviously had a good look over the bike to conclude it was the issue. It wasn't, it was the throttle position sensor alignment. If you've had these fail before it's something you'll go to first, but to the uninitiated it's very quirky. I would argue it's clearly an outdated and st design but I'm not an engineer.... Anyway;

(1) When the SET valve fails it will issue a fault code. Not code = no fault.

(2) Whilst the "FI lamp" should be lit to indicate an issue you can bring in the bike into "dealer mode" with a paperclip so you can see the error codes. The connector is covered in a white sleeve and found next to the battery, cross the white w/ thin red, with white w/thin black.

(3) C00, indicates there are no error codes. There is however, a small line which indicates the throttle position sensor alignment to the immediate left of the code, i.e. _C00,-C00, or ^-C00 (should be superscript hyphen but I don't know how to do it).

(4) If the line is anywhere but -C00 (with the engine off, and the throttle not touched) it needs adjusted. This is done loosening a fking regarded T25 security hex, positioned by Satan himself (on the L1 onwards model), and slowly rotating the lower sensor (the secondary sensor is above it), waiting a moment, and then seeing if the little line moves. Once aligned you can then tighten the bolt. I would recommend replacing the bolt with an Allen bolt, so that you can get a better angle on the bolt should it need to be adjusted again.

The A/F mapping is obviously dependent on knowing where the throttle is, and if the wk little sensor goes out of alignment it will run like st, but thanks a fking awful design, will not produce an error code despite there being a way of telling from the dealer mode.

Whether or not the fact it happened when the SET valve is activated is coincidental in my case I don't know. But if like me your bike suddenly is borderline unrideable, and if you're stuck by the side of the road in a remote location, it might be worth disconnecting the SET to see if you can get home. Alternatively stick a Torx-25 security bit and paperclip in your toolkit. It may be worth replacing the bolt with an Allen type pro-actively, as access to remove a Torx-25 security bolt is restricted by the frame in later models, not easy by a roadside.

After adjustment, including replacing out of spec plugs, and rancid air filter, bike now runs sweet as. Very happy.