Lowering forks through the triple clamp
Lowering forks through the triple clamp
Author
Discussion

skahigh

Original Poster:

2,023 posts

162 months

Wednesday 21st June 2017
quotequote all
Perhaps this is one for the dumb questions thread...

I've been having a little play with my suspension settings today and reading up to try and understand it all a bit better.

I've just read a suggestion that the forks should be lowered through the triple clamp so that 4mm of fork are showing above.

Having checked my bike, there is a 1mm difference between the forks, one is 4mm and the other is 5mm.

My question is, how obvious would this be?

I've always noticed that if I take my hands off the bars I seem to drift to the left and that left hand bends feel a little easier to turn in to than right hand bends but I put this down to me maybe not sitting straight on the seat or something.

Would this 1mm difference now explain the above?

Fleegle

16,710 posts

207 months

Wednesday 21st June 2017
quotequote all
I must have read that book wrong



50mm if I remember correctly

Jazoli

9,707 posts

281 months

Wednesday 21st June 2017
quotequote all
You drift to the left because of the camber of the road, 1mm will make the tiniest difference that you'd never notice.

skahigh

Original Poster:

2,023 posts

162 months

Wednesday 21st June 2017
quotequote all
laugh

Biker's Nemesis

41,487 posts

239 months

Wednesday 21st June 2017
quotequote all

black-k1

12,813 posts

260 months

Wednesday 21st June 2017
quotequote all
Firstly, there isn't a standard formula that works for all bikes. The amount you lower the front by will depend on many things. On a sports bike it's all to easy to go a little too far and make the bike unstable. Add in 5mm at a time and give the bike a good test, including on bumpy roads.

The forks should be set at the same height but 1mm difference won't make a huge difference.

pitlane

301 posts

212 months

Wednesday 21st June 2017
quotequote all
Are we talking road or circuit use?

Benni

3,726 posts

242 months

Wednesday 21st June 2017
quotequote all
Remember that by putting the forks through the yokes you alter the chassis,

get less trail and a steeper fork angle, is what you want ?

skahigh

Original Poster:

2,023 posts

162 months

Wednesday 21st June 2017
quotequote all
I'm not looking to alter it at the moment, I was wondering if a difference of 1mm between the forks would have any effect, it sounds like the answer is no.

It was probably a silly question to ask but if you don't know, you don't know.

Thanks for the replies.

King Herald

23,501 posts

247 months

Thursday 22nd June 2017
quotequote all
skahigh said:
I'm not looking to alter it at the moment, I was wondering if a difference of 1mm between the forks would have any effect, it sounds like the answer is no.

It was probably a silly question to ask but if you don't know, you don't know.

Thanks for the replies.
Oddly enough, your lowers fork legs are actually able to slid up and down freely on the uppers, so 1mm is not going to make ANY difference to anything, anywhere, ever.

Your lower legs are solidly bolted together by the spindle, the mudguard and/or the form brace, so it is not like your wheel is on a 1mm angle.

Chances are the springs inside are more than 1mm difference in length anyway.

And all the talk about sliding them up 5mm, to change the handling, I bet any rider here £1000 they could not tell the different if I did it to their bike or not. laughlaughlaugh

Maybe a pro rider, maybe on a track, with slicks....maybe....

Biker's Nemesis

41,487 posts

239 months

Thursday 22nd June 2017
quotequote all
I went the opposite way with my track R1, I pushed them through (down) by 10mm.

And yes I could tell the difference.

pitlane

301 posts

212 months

Thursday 22nd June 2017
quotequote all
King Herald said:
And all the talk about sliding them up 5mm, to change the handling, I bet any rider here £1000 they could not tell the different if I did it to their bike or not. laughlaughlaugh

Maybe a pro rider, maybe on a track, with slicks....maybe....
I can assure you a racer on circuit will feel 5mm ride height change to the front! Slicks are not relevant to the debate.

sjtscott

4,215 posts

262 months

Thursday 22nd June 2017
quotequote all
King Herald said:
And all the talk about sliding them up 5mm, to change the handling, I bet any rider here £1000 they could not tell the different if I did it to their bike or not. laughlaughlaugh
Year ago I put a post up asking if people on BB could tell the difference in handling between a full petrol tank or an empty one to how their bike handles.. as I remember most couldn't tell.. this says all I need to know.
I can tell a difference in full to empty tank I'm sure there are some on here who can too but was amazing at those saying they couldn't.

I can feel a difference in rear suspension response on my bike removing 4psi from the tyre over recommended for example too. It rides much much better.

So you'll have some people you'll be paying that money too but the vast majority you'll be keeping it.

skahigh

Original Poster:

2,023 posts

162 months

Thursday 22nd June 2017
quotequote all
Argh, poorly title thread was poorly titled.

Can we just accept that I'm a fkwit (for the THIRD time) and move on?

Jazoli

9,707 posts

281 months

Thursday 22nd June 2017
quotequote all
King Herald said:
And all the talk about sliding them up 5mm, to change the handling, I bet any rider here £1000 they could not tell the different if I did it to their bike or not. laughlaughlaugh
I'll take that bet, as will a few others on here smile

As long as the bike in question isn't one of these

biggrin

Edited by Jazoli on Thursday 22 June 11:59

Prof Prolapse

16,163 posts

221 months

Thursday 22nd June 2017
quotequote all
Jazoli said:
I'll take that bet, as will a few others on here smile
Can I try it myself first and then come back?


moanthebairns

19,183 posts

229 months

Thursday 22nd June 2017
quotequote all
triumph recommend 4 mm off top, which is what I have.

would increasing this equate to a faster turn in?

Jazoli

9,707 posts

281 months

Thursday 22nd June 2017
quotequote all
moanthebairns said:
triumph recommend 4 mm off top, which is what I have.

would increasing this equate to a faster turn in?
Yes, but it can also make the bike quite unstable if you go too far as you are altering the geometry significantly and you could run into clearance issues twixt mudguard and radiator, and exhaust and road!

Steve Bass

10,756 posts

264 months

Thursday 22nd June 2017
quotequote all
King Herald said:
skahigh said:
I'm not looking to alter it at the moment, I was wondering if a difference of 1mm between the forks would have any effect, it sounds like the answer is no.

It was probably a silly question to ask but if you don't know, you don't know.

Thanks for the replies.
Oddly enough, your lowers fork legs are actually able to slid up and down freely on the uppers, so 1mm is not going to make ANY difference to anything, anywhere, ever.

Your lower legs are solidly bolted together by the spindle, the mudguard and/or the form brace, so it is not like your wheel is on a 1mm angle.

Chances are the springs inside are more than 1mm difference in length anyway.

And all the talk about sliding them up 5mm, to change the handling, I bet any rider here £1000 they could not tell the different if I did it to their bike or not. laughlaughlaugh

Maybe a pro rider, maybe on a track, with slicks....maybe....
Wow.. When you're wrong you really give it your all.
Thank God chassis designers and Suspension Companies don't follow your thinking.


MotorsportTom

3,343 posts

192 months

Thursday 22nd June 2017
quotequote all
Steve Bass said:
King Herald said:
skahigh said:
I'm not looking to alter it at the moment, I was wondering if a difference of 1mm between the forks would have any effect, it sounds like the answer is no.

It was probably a silly question to ask but if you don't know, you don't know.

Thanks for the replies.
Oddly enough, your lowers fork legs are actually able to slid up and down freely on the uppers, so 1mm is not going to make ANY difference to anything, anywhere, ever.

Your lower legs are solidly bolted together by the spindle, the mudguard and/or the form brace, so it is not like your wheel is on a 1mm angle.

Chances are the springs inside are more than 1mm difference in length anyway.

And all the talk about sliding them up 5mm, to change the handling, I bet any rider here £1000 they could not tell the different if I did it to their bike or not. laughlaughlaugh

Maybe a pro rider, maybe on a track, with slicks....maybe....
Wow.. When you're wrong you really give it your all.
Thank God chassis designers and Suspension Companies don't follow your thinking.
I'd be pretty confident they don't engineer springs to be +/- 1mm tolerance.

I'm a st rider and I'd take the bet of moving it 5mm