Removing news pads from monobloc calipers
Discussion
Had to do a couple of jobs on the bike last weekend... Nothing major; front pads, fluid and front wheel alignment.
Did the business and threw it back together. As is often the case the alignment wasn't perfect on the first attempt so tried again. I was getting a small amount of rubbing on one caliper so opted to push the pistons all the way back and let it re-seat with my now-aligned front wheel.
Now with the Brembo M4 there is ample room to remove worn pads, but not new ones unless you push one of the pads back. See here:

Due to the fact I needed to get the job done I ended up prying them with a flat object. This ends up f
king the pads though which I'd rather avoid the next time I'm presented with this problem.
So how do you do it?
Did the business and threw it back together. As is often the case the alignment wasn't perfect on the first attempt so tried again. I was getting a small amount of rubbing on one caliper so opted to push the pistons all the way back and let it re-seat with my now-aligned front wheel.
Now with the Brembo M4 there is ample room to remove worn pads, but not new ones unless you push one of the pads back. See here:

Due to the fact I needed to get the job done I ended up prying them with a flat object. This ends up f
king the pads though which I'd rather avoid the next time I'm presented with this problem.So how do you do it?
Take worn pads out which will leave the pistons exposed, clean the pistons with a tooth brush using brake cleaner then a bit of WD40 wiping off any excess.
Re fit the old pads and lever back the pistons with anything you like.
Take the old pads out again which will leave plenty of room too fit the new pads
Re fit the old pads and lever back the pistons with anything you like.
Take the old pads out again which will leave plenty of room too fit the new pads
Push the pistons back in with your thumbs before you put the pads in, or use one of these, or the old pads as BN has already said.

https://www.amazon.co.uk/OTC-OTC4743-Motorcycle-Ca...

https://www.amazon.co.uk/OTC-OTC4743-Motorcycle-Ca...
Edited by Jazoli on Tuesday 5th September 13:13
To be clear, new pads need to be pushed back in order to remove them and therefore access the pistons.
Order of events
Old pads removed, pistons cleaned and pushed back
New pads fitted
Pads pushed up against the disc
Now I need to remove the new pads
For what it's worth, I've finished the job and everything is fine. I just want to know how to do it without f
king the pads the next time I need to remove them.
Order of events
Old pads removed, pistons cleaned and pushed back
New pads fitted
Pads pushed up against the disc
Now I need to remove the new pads
For what it's worth, I've finished the job and everything is fine. I just want to know how to do it without f
king the pads the next time I need to remove them.shielsy said:
Now with the Brembo M4 there is ample room to remove worn pads, but not new ones unless you push one of the pads back. See here:

Due to the fact I needed to get the job done I ended up prying them with a flat object. This ends up f
king the pads though which I'd rather avoid the next time I'm presented with this problem.
So how do you do it?
It's due to the pin-less design which frankly I found a total pain the arse. Even seating the pads can be fiddly.
Due to the fact I needed to get the job done I ended up prying them with a flat object. This ends up f
king the pads though which I'd rather avoid the next time I'm presented with this problem.So how do you do it?
For the new pad issue. i.e. removal I just use a piece of wood between the pads and twist it gently to seat the pistons on one side so the pads can be removed. The annoying thing is if the pads are nearly new but the pistons are covered in s
t from the road you can't take the pads out to clean the pistons without pushing the pistons back slightly and hence all the crap into the seals... CarsOrBikes said:
, if worried about that dirt being drawn into calipers, remove old pads, clean up, refit old, spread as intended, continue with renewal. What's not to like?
Again, you can't do that with Brembo M4's without pushing the pistons back to remove the pads... i.e. the pads won't come out due to the pinless design.There's loads of specific tools that will be kinder to the pads, but I tend to just use a 1" wide tyre lever and be very gentle with it with new pads.
To remove the pistons, you do need a removal tool though, and even then it's still a ball ache.
The more often you do it, the easier they are to remove as they're obviously cleaner, and you can just about do it by hand at times. The other method to make piston removal easier is the leave them in some very hot water for a few mins to put some heat in the seals and soften them up
To remove the pistons, you do need a removal tool though, and even then it's still a ball ache.
The more often you do it, the easier they are to remove as they're obviously cleaner, and you can just about do it by hand at times. The other method to make piston removal easier is the leave them in some very hot water for a few mins to put some heat in the seals and soften them up
Gassing Station | Biker Banter | Top of Page | What's New | My Stuff






