Pinlock visors
Discussion
had a new visor and pinlock on my caberg helmet a few months ago, and its been fine up till now.
i dont know if pinlocks shrink, but all of a sudden i have a large gap at the bottom of the pinlock causing the visor to mist up.
Does anyone have any tips on adjusting the pinlock to fit better.
when i have tried adjusting it before with a pair of pliers to try and rotate the pin, i end up chewing the pin up, and the pinlock not fitting well on one side.
i'm not sure whats best to use to adjust the pin, or if its just better to take it into the shop i bought it from and let them adjust it.
thanks
i dont know if pinlocks shrink, but all of a sudden i have a large gap at the bottom of the pinlock causing the visor to mist up.
Does anyone have any tips on adjusting the pinlock to fit better.
when i have tried adjusting it before with a pair of pliers to try and rotate the pin, i end up chewing the pin up, and the pinlock not fitting well on one side.
i'm not sure whats best to use to adjust the pin, or if its just better to take it into the shop i bought it from and let them adjust it.
thanks
Google is your friend.. have a look for the pinlock website where they have instructions for doing this adjustment correctly.
Basically the indicator on the pins needs to be turned towards each other i.e. facing into the visor to tighten the seal, they say the pinlock insert has to come off to do this. I found I had a small perfectly fitting odd sized socket to help me turn enough with my fingers in situe - I wouldn't use pilers.
> < = tightest position
Basically the indicator on the pins needs to be turned towards each other i.e. facing into the visor to tighten the seal, they say the pinlock insert has to come off to do this. I found I had a small perfectly fitting odd sized socket to help me turn enough with my fingers in situe - I wouldn't use pilers.
> < = tightest position
Yes, read all of the above carefully and you may find that after you spend 15 minutes lovingly washing everything, putting the pinlock in place and carefully adjusting the pins you'll discover that the inside of the visor (i.e. the pinlock) now scrapes the rubber seal at the top of the lid just enough to push the pinlock out of place each time you lift the visor, rendering the whole
ing excercise pointless and you're looking at the gap between the bottom of the pinlock and the visor.
Why the f
king f
k the
s charging several hundred for a helmet with a good £50 for a visor haven't come up with a f
king permanent solution which does not require twisting two f
king clits with tweezers with bated breath is anyone's guess.
ing excercise pointless and you're looking at the gap between the bottom of the pinlock and the visor.Why the f
king f
k the
s charging several hundred for a helmet with a good £50 for a visor haven't come up with a f
king permanent solution which does not require twisting two f
king clits with tweezers with bated breath is anyone's guess.Every one of the Shark helmets I've had has been equipped with a visor that has an anti-mist coating....and it works. However, their latest ones do have visors that are 'Pinlock ready'......as well as the anti-fog treatment!.......because customers 'expect' Pinlock. Presumably some folk actually look forward to all the faffing about!
Pete
Pete
pessimal said:
had a new visor and pinlock on my caberg helmet a few months ago, and its been fine up till now.
i dont know if pinlocks shrink, but all of a sudden i have a large gap at the bottom of the pinlock causing the visor to mist up.
Does anyone have any tips on adjusting the pinlock to fit better.
Having had several pinlocks, IMHO they last 6 months, then they are fi dont know if pinlocks shrink, but all of a sudden i have a large gap at the bottom of the pinlock causing the visor to mist up.
Does anyone have any tips on adjusting the pinlock to fit better.
ked, then you have to buy a new one. sjtscott said:
Google is your friend.. have a look for the pinlock website where they have instructions for doing this adjustment correctly.
Basically the indicator on the pins needs to be turned towards each other i.e. facing into the visor to tighten the seal, they say the pinlock insert has to come off to do this. I found I had a small perfectly fitting odd sized socket to help me turn enough with my fingers in situe - I wouldn't use pilers.
> < = tightest position
you managed to find a small socket to put over the pinlock pin to turn it?Basically the indicator on the pins needs to be turned towards each other i.e. facing into the visor to tighten the seal, they say the pinlock insert has to come off to do this. I found I had a small perfectly fitting odd sized socket to help me turn enough with my fingers in situe - I wouldn't use pilers.
> < = tightest position
what sort of size was it?
cheers
Same here, my Schuberth's old enough that I'm thinking I really need to replace it pretty soon and I'm still on the original pinlock. I did get a bit of trouble with it steaming up at the bottom between the layers a couple of years ago but I took it out, gave everything a clean, ensured it was seated properly when I put it back in, and have had no more trouble.
pessimal said:
getting more tempted just to stick some duct tape around the outside of it and have done!
tried to get one of the pinlock pins out last night and was unable to, i need to find something to rotate them in place.
How do you mean out? Mine have a little hex adjuster on the inside, gentle work with pliers or a if you have atiny socket should do it. You shouldn't have to take them out at all.tried to get one of the pinlock pins out last night and was unable to, i need to find something to rotate them in place.
Take the visor out, remove the pinlock ( you need to flatten the visor), wash it all down and let it dry, set the pins to neutral (using the little arrows) and reinstall. Then adjust the pins and gibe it a wiggle until it is seated correctly.
anonymous said:
[redacted]
Catcrap works fairly well (no not out of a feline, have a search on e-bay), but I found changing to a helmet with better ventilation made the biggest different, it has to be seriously cold out for my glasses to team up in my Schuberth C3, where as it was a pain in the arse in my Shoei Raid.got it sorted.
all this talk of hex and crossheads had me confused.
i have this type of pinlock pin
rather than 
in the end i had to use brute force to pop the pin out (causing a tiny crack in the visor in the process) rotate it, and them pop in back in with even more force!
think i might buy some of the pinlock pins with the screw or hex in them to make this a little less frustrating next time
all this talk of hex and crossheads had me confused.
i have this type of pinlock pin

in the end i had to use brute force to pop the pin out (causing a tiny crack in the visor in the process) rotate it, and them pop in back in with even more force!
think i might buy some of the pinlock pins with the screw or hex in them to make this a little less frustrating next time
My recent glasses (vari-focal) have an 'anti-glare' coating - works well to prevent glare but it also stops any anti-mist coating from working
. When out on the bike (or skiing) I have to go back to my old bi-focals which take the anti mist fine....
Alternatively - remove glasses and work on 'zen navigation' much more fun
. When out on the bike (or skiing) I have to go back to my old bi-focals which take the anti mist fine....Alternatively - remove glasses and work on 'zen navigation' much more fun
Gassing Station | Biker Banter | Top of Page | What's New | My Stuff




