Best brake fluid
Discussion
Hello from a long time lurker, I have a question about brake fluid; in particular what is the opinion out there on the best brake fluid for bikes?
I use ATE TYP200 in my cars as it has the good combination of a decent dry boiling point, a pretty decent wet boiling point and a sensible life for road vehicles - i.e. you don't have to flush it through every six weeks. What about bikes though?
Bit of background - I've got an old Thundercat - it's done bugger all mileage prior to me buying it, mostly been stored, so I'm working on re-commissioning it: new hoses, seals, pads and fluid as I don't much fancy what's been in there for potentially twenty years!
I use ATE TYP200 in my cars as it has the good combination of a decent dry boiling point, a pretty decent wet boiling point and a sensible life for road vehicles - i.e. you don't have to flush it through every six weeks. What about bikes though?
Bit of background - I've got an old Thundercat - it's done bugger all mileage prior to me buying it, mostly been stored, so I'm working on re-commissioning it: new hoses, seals, pads and fluid as I don't much fancy what's been in there for potentially twenty years!
bgunn said:
Biker 1 said:
Isn't DOT4 the same recipe whatever brand it is?
Yes, but there are differences in viscosity, boiling points etc etc. Just interested to see if there's a trend with bikes that differs, really, given the general difference between a car and a bike braking system(s).I think it's worth stating that I'm well aware that I'm unlikely to achieve the required braking efforts to get even close to boiling points of even standard DOT 4 specification fluids. I'm not suggesting I'm a better driver or rider than anyone, as I detect an overtone of "why do you think you need that?".
BUT.
I think the point is being missed here though. If the fluid is out, you put the best compromise you can back in - i.e. high dry and wet boiling points, least hygroscopic fluids possible, and most incompressible possible (within a set of compromises of course, it's no good if you have to change the fluid every week to keep those specs). To use the same analogy - none of us *need* 300hp cars, but we drive them because they feel good. Likewise with the component parts of my vehicles - you fit the best you can that suit the purpose.
My car gets the best (within the boundaries of performance road usage) because it's a primary safety system, so I just wanted to achieve the same with my bike.
I'll probably be putting the Motul RBF 600 fluid in, thanks for the tip Mr OCD - it's usefully improved in specs over ATE TYP200 (which transformed the pedal and feel of any car I've filled with it), so that's a nice thing to have.
BUT.
I think the point is being missed here though. If the fluid is out, you put the best compromise you can back in - i.e. high dry and wet boiling points, least hygroscopic fluids possible, and most incompressible possible (within a set of compromises of course, it's no good if you have to change the fluid every week to keep those specs). To use the same analogy - none of us *need* 300hp cars, but we drive them because they feel good. Likewise with the component parts of my vehicles - you fit the best you can that suit the purpose.
My car gets the best (within the boundaries of performance road usage) because it's a primary safety system, so I just wanted to achieve the same with my bike.
I'll probably be putting the Motul RBF 600 fluid in, thanks for the tip Mr OCD - it's usefully improved in specs over ATE TYP200 (which transformed the pedal and feel of any car I've filled with it), so that's a nice thing to have.
Edited by anonymous-user on Thursday 28th September 23:21
Part of the compromise with the higher dry boiling point fluids is that they usually have a lower wet boiling point and absorb water more readily so need changed more often.
So whilst we don't need 300bhp, but we want it, it would be better to have a 250bhp car that didn't need an engine rebuild as opposed to a 300bhp one that did
So whilst we don't need 300bhp, but we want it, it would be better to have a 250bhp car that didn't need an engine rebuild as opposed to a 300bhp one that did
mckeann said:
Part of the compromise with the higher dry boiling point fluids is that they usually have a lower wet boiling point and absorb water more readily so need changed more often.
So whilst we don't need 300bhp, but we want it, it would be better to have a 250bhp car that didn't need an engine rebuild as opposed to a 300bhp one that did
I didn't see such a compromise comparing what is considered a very good fluid (the ATE) to Motul though? Just a bigger safety margin.So whilst we don't need 300bhp, but we want it, it would be better to have a 250bhp car that didn't need an engine rebuild as opposed to a 300bhp one that did
A branded DOT4 is what is recommended and all you need.
Although there is probably nowt wrong with Comma DOT4 or Halfords 10W40 for your engine, saving a few quid on something you change at most once a year is daft.
Although not nearly as daft as the idiots that cheapskate on tyres, saving themselves £1 a week to run Cheng s
ts instead of Michelins.
Although there is probably nowt wrong with Comma DOT4 or Halfords 10W40 for your engine, saving a few quid on something you change at most once a year is daft.
Although not nearly as daft as the idiots that cheapskate on tyres, saving themselves £1 a week to run Cheng s
ts instead of Michelins.mckeann said:
Part of the compromise with the higher dry boiling point fluids is that they usually have a lower wet boiling point and absorb water more readily so need changed more often.
Yes, they do need changing more often. I do mine once year ... but no they do not have a lower wet boiling point when compared to a standard DOT 4.You do get a better lever / pedal with decent Super DOT 4 fluid that is noticeable ...
We aren't talking massive differences in cost here ... a few pounds at most between standard DOT 4 and Super DOT 4 ... so why not ...
... this is like an oil argument

cmaguire said:
A branded DOT4 is what is recommended and all you need.
Although there is probably nowt wrong with Comma DOT4 or Halfords 10W40 for your engine, saving a few quid on something you change at most once a year is daft.
Although not nearly as daft as the idiots that cheapskate on tyres, saving themselves £1 a week to run Cheng s
ts instead of Michelins.
I use the cheapest sAlthough there is probably nowt wrong with Comma DOT4 or Halfords 10W40 for your engine, saving a few quid on something you change at most once a year is daft.
Although not nearly as daft as the idiots that cheapskate on tyres, saving themselves £1 a week to run Cheng s
ts instead of Michelins.
t I can get, but draw the line at bike tyres, as I like the feel of decent rubber
My commuting car has a mixture of weird Chinese & I think Slovenian (?) tyres - seems to get me to work OK, although the highest speed I get to is 40.... Anyway, what's the price difference between Halfords DOT4 & the 'decent' stuff?
Biker 1 said:
I use the cheapest s
t I can get, but draw the line at bike tyres, as I like the feel of decent rubber
My commuting car has a mixture of weird Chinese & I think Slovenian (?) tyres - seems to get me to work OK, although the highest speed I get to is 40....
Anyway, what's the price difference between Halfords DOT4 & the 'decent' stuff?
Comma Dot 4 is £8 against Mobil at £9, both 500mL at Halfords
t I can get, but draw the line at bike tyres, as I like the feel of decent rubber
My commuting car has a mixture of weird Chinese & I think Slovenian (?) tyres - seems to get me to work OK, although the highest speed I get to is 40.... Anyway, what's the price difference between Halfords DOT4 & the 'decent' stuff?
Just why would you?
Gassing Station | Biker Banter | Top of Page | What's New | My Stuff




