10p resistor fixed my Blackbird
Discussion
I've had my Blackbird for over 5 years, and I've always just accepted that the thing didn't like going slow. For instance, filtering meant using first or second and just revving it's nuts off in order to make smooth progression.
Symptoms were: At anything below ~3k rpm the bike felt lumpy and sluggish. Kind of like something was holding it back.
I was almost at the point of getting rid of it because I do a lot of commuting now, and filtering or getting stuck in slow traffic was a tiresome experience. I Googled the problem and lo and behold, I was not alone - in fact, a lot of VFR owners were complaining of the same problems.
It turns out an 'O2 eliminator' is the answer (in fact, just a 10p 330Ω linking the signal wires or a £10 plug in eliminator from eBay)
What a difference - the bike now has more low down power, revs are smooth all the way from idle. It feels like a different bike entirely.
I guess ultimately my O2 sensor was shot, but Google seems to suggest it's not really needed. Apparently the ECU uses the O2 sensor to optimise emissions below 3k rpm but is a little too aggressive which is why this common problem happens.
I wish I'd looked into it sooner!
Symptoms were: At anything below ~3k rpm the bike felt lumpy and sluggish. Kind of like something was holding it back.
I was almost at the point of getting rid of it because I do a lot of commuting now, and filtering or getting stuck in slow traffic was a tiresome experience. I Googled the problem and lo and behold, I was not alone - in fact, a lot of VFR owners were complaining of the same problems.
It turns out an 'O2 eliminator' is the answer (in fact, just a 10p 330Ω linking the signal wires or a £10 plug in eliminator from eBay)
What a difference - the bike now has more low down power, revs are smooth all the way from idle. It feels like a different bike entirely.
I guess ultimately my O2 sensor was shot, but Google seems to suggest it's not really needed. Apparently the ECU uses the O2 sensor to optimise emissions below 3k rpm but is a little too aggressive which is why this common problem happens.
I wish I'd looked into it sooner!
I sold my 2006 Blackbird in early 2016, I had the O2 Eliminator fitted to fix the low down lean surge caused by the emissions crap Honda had to put into the ECU. You got completely inconsistent throttle at low commuting/filtering revs/speed. Fooling the ECU into thinking it doesn't need to go into this mode is the fix here.
Whilst a resistor of the correct rating does fix it, I paid for the sealed plug and play Dynojet one which does the same job for of course more money.
Whilst a resistor of the correct rating does fix it, I paid for the sealed plug and play Dynojet one which does the same job for of course more money.
2wheelsjimmy said:
Mine must have this, as no such issues.
Is yours a 2003 or later Fi model? if not then you are correct you won't have this issue. If it is then you're not riding it in the conditions where you'll notice this issue or it has already been fixed - that has also been the case of others thinking they arn't affected.Its only the final model variant of injected blackbirds which have this. The early carbed or non cat Fi models don't have this ECU mode/issue
Edited by sjtscott on Wednesday 4th October 15:38
sjtscott said:
Is yours a 2003 or later Fi model? if not then you are correct you won't have this issue. If it is then you're not riding it in the conditions where you'll notice this issue or it has already been fixed - that has also been the case of others thinking they arn't affected.
Its only the final model variant of injected blackbirds which have this. The early carbed or non cat Fi models don't have this ECU mode/issue
Ah 2000 fi model, so that's why then.Its only the final model variant of injected blackbirds which have this. The early carbed or non cat Fi models don't have this ECU mode/issue
Edited by sjtscott on Wednesday 4th October 15:38
Gassing Station | Biker Banter | Top of Page | What's New | My Stuff



