Question for MT10/New R1 Owners
Discussion
Nothing exciting but have any owners of the above fitted different indicators to their bike?
I've just bought a set of 2nd hand MT10, genuine standard LED indicators to fit my FZ1, expecting to use resistors on each/each pair.
They have arrived and have extra bits on the wiring, all factory by Yamaha. A little peeling back of the tape and reveals what I think are resistors built in line (or rather not in-line but in long bits of plastic tube & insulation going off at random angles).
Any MT10 owners who changed, did you have to use new resistors? From what I see, I'm hoping I won't have to now.
I've just bought a set of 2nd hand MT10, genuine standard LED indicators to fit my FZ1, expecting to use resistors on each/each pair.
They have arrived and have extra bits on the wiring, all factory by Yamaha. A little peeling back of the tape and reveals what I think are resistors built in line (or rather not in-line but in long bits of plastic tube & insulation going off at random angles).
Any MT10 owners who changed, did you have to use new resistors? From what I see, I'm hoping I won't have to now.
Dog Star said:
My new R1 has those, and they are resistors. However I couldn't tell you whether or not they'll have the right impedance to make them flash correctly; I can only suggest trying them first by just plugging them in.
Thanks Dogstar. You're right, not the correct impedance, tried last night & they flash too fast.
Resistors it will have to be, was hoping to keep it all Yamaha parts as been let down with aftermarket indicator stuff before.
Any advice on good or bad resistors? Has anyone experience (and what size/spec) in getting resistors from somewhere like Maplins? - only reason I ask is I'm passing Maplins later, won't be able to get to any local bike shops for a couple of weeks now.
graham22 said:
Thanks Dogstar.
You're right, not the correct impedance, tried last night & they flash too fast.
Resistors it will have to be, was hoping to keep it all Yamaha parts as been let down with aftermarket indicator stuff before.
Any advice on good or bad resistors? Has anyone experience (and what size/spec) in getting resistors from somewhere like Maplins? - only reason I ask is I'm passing Maplins later, won't be able to get to any local bike shops for a couple of weeks now.
Did you try both new indicators wired in on the same side when you tested the flashing rate??If only 1 you might not have the correct resistance for your relay.You're right, not the correct impedance, tried last night & they flash too fast.
Resistors it will have to be, was hoping to keep it all Yamaha parts as been let down with aftermarket indicator stuff before.
Any advice on good or bad resistors? Has anyone experience (and what size/spec) in getting resistors from somewhere like Maplins? - only reason I ask is I'm passing Maplins later, won't be able to get to any local bike shops for a couple of weeks now.
If both were wired in, get the R1/MT10 relay as it'll be set up to the right flash rate with those indicators. No need to mess about adding or removing resistors
Steve Bass said:
Did you try both new indicators wired in on the same side when you tested the flashing rate??If only 1 you might not have the correct resistance for your relay.
If both were wired in, get the R1/MT10 relay as it'll be set up to the right flash rate with those indicators. No need to mess about adding or removing resistors
Did try front & back too. I did think about at MT10 relay but it was mentioned that with the canbus system on the MT10, the relay may be used for other functions too. If both were wired in, get the R1/MT10 relay as it'll be set up to the right flash rate with those indicators. No need to mess about adding or removing resistors
There are aftermarket relays available for LED indicators, will try one over the weekend - will help keep things tidier under the seat.
Gassing Station | Biker Banter | Top of Page | What's New | My Stuff


